Page 1
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E RMT-708 AEP Model SERVICE MANUAL East European Model North European Model Ver 1.1 2000. 11 Russian Model CCD-TR417E/TR427E/TR617E/TR717E/ TR918E/TRV37E/TRV48E/TRV57E/ TRV67E/TRV87E UK Model CCD-TR417E/TR427E/TR717E/ TR918E/TRV37E/TRV48E/ TRV57E/TRV67E/TRV87E E Model Hong Kong Model Australian Model Chinese Model CCD-TR317E/TRV47E/TRV57E/ Photo : CCD-TRV87E...
Page 2
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
TABLE OF CONTENTS SERVICE NOTE 2-2. FRONT PANEL ASSEMBLY, MA-374/375 BOARD ···· 2-3 2-3. CABINET (R) BLOCK ASSEMBLY ····························· 2-4 POWER SUPPLY DURING REPAIRS ····························· 7 2-4. MECHANISM DECK-1 ················································· 2-5 TO TAKE OUT A CASSETTE WHEN NOT EJECT 2-5. EVF BLOCK ASSEMBLY ············································· 2-6 (FORCE EJECT) ································································...
SERVICE NOTE POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied (8.4V) to the battery terminal using the service power cord (J-6082-223-A), the power is shut off so that the unit cannot operate. This following two methods are available to prevent this. Take note of which to use during repairs.
SELF-DIAGNOSIS FUNCTION Self-diagnosis Function Self-diagnosis Display When problems occur while the unit is operating, the counter of the When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder or Display viewfinder or Display window shows a 4-digit display consisting window what to do.
Self-diagnosis Code Table Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Non-standard battery is used. Use the InfoLITHIUM battery. Condensation. Remove the cassette, and insert it again after one hour. Video head is dirty. Clean with the optional cleaning cassette. LOAD direction.
Page 10
Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Inspect the lens block focus reset sensor (Pin qs of CN551 of VC- 234 board) when focusing is performed when the control dial is Difficult to adjust focus rotated in the focus manual mode and the focus motor drive circuit (Cannot initialize focus.) (IC551 of VC-234 board) when the focusing is not performed.
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E SECTION 1 This section is extracted from instruction manual. (3-868-324-11) GENERAL...
NOTE: Follow the disassembly procedure in the numerical order given. 2-1. PD-117 BOARD, BACK LIGHT, LIQUID CRYSTAL DISPLAY PANEL (TRV MODEL) REMOVING THE BACK LIGHT (TRV87E MODEL) 4 P cabinet (C)(98) 7 Two tapping screws (B2 × 7) 3 Two claws 1 Two screws (M2 ×...
[MECHANISM DECK SERVICE POSITION-1] Note: Use the parts only which can be removed easily from outside of the mechanism deck. CPC-7 jig • How to move up the cassette (J-6082-382-A) Adjustment remote compartment manually commander (RM-95) Control switch block Press the cassette compartment (SS-9700) in the direction of the arrow C to move it up in the direction of...
2-6. VF-129 BOARD 4 Finder (S) assembly 3 Rotate it in the direction of the arrow B and remove it in the direction of the arrow C . 8 FFC-289 flexible flat cable 1 F lock Tilt lock (93) screw (T) 2 Slide the button in the direction of the arrow A .
2-7. LENS DEVICE, CD-239/240 BOARD [ VIDEO LIGHT MODEL ] 1 Screw (M2 × 3) 2 VL-28 board (TR video light model) VL-29 board (TRV video light model) 5 Two screws (M2 × 3) REMOVING THE LENS DEVICE, CD-239/240 BOARD 7 Flexible board 7 Shield rubber (FM) 3 FP-147...
Page 44
2-9. VC-234, EJ-29/30 BOARDS, MECHANISM DECK-2 PRECAUTION DURING INSTALLATION 4 Control switch block (FK-8500) (10P) Control switch block 1 Claw (FK-8500) 3 Peel off the area shown by shading. 6 Control switch block 2 Slide it in the direction (SS-9700) of the arrow A and Adhering 5 EJ-29 board...
[CONNECTION DIAGRAM FOR SERVICE POSITION (Mainly for voltage measurement and check)] MA-374/375, CF-66/67, CD-239/240, VL-28/29, PJ-99/100, SE-100/101, EJ-29/30, DD-134, VC-234 BOARDS, MECHANISM DECK-2 AC IN AC POWER Battery panel ADAPTOR CPC-7 jig block assembly (J-6082-382-A) Control switch block DC IN (SS-9700) Adjustment remote DD-134 board...
Page 48
2-13.HARNESS PROCESSING OF THE HINGE ASSEMBLY (TRV MODEL) [ASSEMBLING THE HARNESS CLAMP] Attach the harness clamp to the DP-78 harness. (8P) Harness clamp (12P) (6P) Himeron • Place a longer harness to the left side. DP-78 harness Place the shortest harness (8P) in the right side to the bottom. •...
2-15.FLEXIBLE BOARDS LOCATION CONTROL SWITCH BLOCK (FK-8500) FP-249 FP-46 (Video light model) FP-150 FP-248 FP-221 From S/T REEL SENSOR From CAPSTAN MOTOR FP-355 FP-44 From DRUM FP-356 TR steady shot model MOTOR and TRV model From VIDEO FP-220 HEAD From LOADING MOTOR, MODE SWITCH CONTROL SWITCH BLOCK (SS-9700)
CF-67 BOARD(1/2) (TRV MODEL) PANEL TIMING H OUT GENERATOR (TRV MODEL) DV1,DV2 IC5502 (4-75) V901 ND901 TR MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E DC/DC TRV MODEL : CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E BACK STEREO MODEL : CCD-TR918E/TRV87E CONVERTER BL REG LIGHT MONAURAL MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TRV37E/TRV47E/TRV48E/TRV57E/TRV67E BACK LIGHT...
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E 3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram. TR MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E TRV MODEL : CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E VIDEO LIGHT MODEL : CCD-TR617E/TR717E/TR918E/TRV57E/TRV67E/TRV87E SUPER NIGHT SHOT MODEL : CCD-TR918E/TRV87E...
(IC902 VC SO (IC902 A 4.75V A 4.75V A 4.75V D 2.8V 0.56Vp-p VC SI (IC902 TR MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E TRV MODEL : CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E V ON Hi8 MODEL : CCD-TR717E/TR918E/TRV67E/TRV87E V JACK IN (IC803 1/6 CCD MODEL : CCD-TR317E/TR417E/TR427E/TRV37E/TRV47E/TRV48E MODE...
CAMERA REC/PB JOG VD (IC902 LCD HOLD (IC902 0.5Vp-p Abbreviation TR MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E : Hong Kong MODEL TRV MODEL : CCD-TRV37E/TRV47E/TRV57E/TRV67E/TRV87E AUS : Australian MODEL VTR REC MODEL : CCD-TRV87E : E,HK,AUS,CN,JE model : Chinese MODEL PHOTO MODE MODEL : CCD-TR918E/TRV87E...
(EJ-29/30) FC XB (SEE PAGE 3-14) OUT 2B DIR0A (IC201 150 ) VM23 EVF DD ON POWER D 2.8V MT 4.75V TR MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E TRV MODEL : CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E STEADY SHOT MODEL : CCD-TR617E/TR717E/TR918E/TRV57E/TRV67E/TRV87E VIDEO LIGHT MODEL : CCD-TR617E/TR717E/TR918E/TRV57E/TRV67E/TRV87E 3-10...
PHOTO LASER LINK PHOTO START (2ND CLICK) (LASER LINK MODEL) Q933,934 LED 5V TR MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E D 2.8V TRV MODEL : CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E SUPER NIGHT SHOT MODEL : CCD-TR918E/TRV87E CN253 LCD INDICATOR BACK LIGHT MODEL : CCD-TR918E/TRV87E CONTROL SWITCH BLOCK...
XLANC ON SHOE ON XS/S SW Q806 VTR DD ON IC802 XEJECT SW (4-29) XLANC JACK IN TR MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E LANC I/O LANC DC TRV MODEL : CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E EVER 3.0V LASER LINK MODEL : CCD-TR918E/TRV87E LANC SIG 3-15 3-16...
IR ON (IC803 (SEE PAGE 3-9) VC SCK (IC902 SIRCS PWM (IC803 59 ) AU XIN/OUT (IC902 TR MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E TRV MODEL : CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E STEREO MODEL : CCD-TR918E/TRV87E MONAURAL MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TRV37E/TRV47E/TRV48E/TRV57E/TRV67E LASER LINK MODEL : CCD-TR918E/TRV87E 3-17 3-18...
XCAM MODE SW CAMERA AUTO S302 POWER PLAYER (VIDEO LIGHT MODEL) XVTR MODE SW CN303 TR MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E TRV MODEL : CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E STEREO MODEL : CCD-TR918E/TRV87E MONAURAL MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TRV37E/TRV47E/TRV48E/TRV57E/TRV67E LASER LINK MODEL : CCD-TR918E/TRV87E REMOTE COMMANDER MODEL : CCD-TR427E/TR617E/TR717E/TR918E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E...
(LCD INDICATOR BACKLIGHT MODEL) POWER(2) BL REG (CF-67) (SEE PAGE 3-28) CN933 TR MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E TRV MODEL : CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E LCD TYPE S MODEL : Refer to "LCD TYPE CHECK". LCD TYPE C MODEL : Refer to "LCD TYPE CHECK".
CAP_VS DRUM_VS REVERS) ACV_GND CAP_VS DRUM_VS BATT/XEXT BATT_UNREG BATT_GND J901 DD-134 BOARD TR MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E BATTERY ACV_UNREG TERMINAL TRV MODEL : CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E BATT_SIG SUPER NIGHT SHOT MODEL : CCD-TR918E/TRV87E BL MODEL : CCD-TR918E/TRV87E DIGITAL EFFECT MODEL : CCD-TR918E/TRV87E FRAME SCHEMATIC DIAGRAM (2/2)
Page 67
• Chip parts. used.) * Transistor Diode 1. Connection Pattern box • Model TR model:CCD-TR317E/TR417E/TR427E/TR617E/TR717E/ TR918E TRV model: CCD-TRV37E/TRV47E/TRV48E/TRV57E/ TRV67E/TRV87E 1.5 m (For schematic diagrams) • All capacitors are in mF unless otherwise noted. pF : m mF. 50V or less are not indicated except for electrolytics and tantalums.
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E For Schematic Diagram • Refer to page 4-35 for printed wiring board. VC-234 BOARD(3/13) EXCEPT PHOTO MODE MODEL PHOTO MODE MODEL FB201 MEMORY(CL-2 BLOCK) D203 EVER_3.0V 1SS357-FPH3 -REF.NO.:1000 SERIES- FB204 XX MARK:NO MOUNT D_1.5V R270 FB202 NO MARK:REC/PB MODE R :REC MODE D_2.8V...
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E For Schematic Diagram • Refer to page 4-35 for printed wiring board. • Refer to page 4-89 for waveforms. VC-234 BOARD(6/13) VTR REC MODEL : CCD-TRV87E:E,HK,AUS,CN,JE Hi8 MODEL : CCD-TR717E/TR918E/TRV67E/TRV87E LINE IN/OUT AMP(IO BLOCK) NO MARK:REC/PB MODE (ABBREVIATION) -REF.NO.:1000 SERIES-...
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E For Schematic Diagram • Refer to page 4-35 for printed wiring board. • Refer to page 4-89 for waveforms. VC-234 BOARD(7/13) NO MARK:REC/PB MODE (LASER LINK MODEL) R :REC MODE IR TRANSMITTER (IR BLOCK) LASER LINK MODEL : CCD-TR918E/TRV87E P :PB MODE -REF.NO.:1000 SERIES-...
• Refer to page 4-35 for printed wiring board. • Refer to page 4-89 for waveforms. R805 TR MODEL 3300 VC-234 BOARD(11/13) TR MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E TRV MODEL : CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E Q801 VIDEO LIGHT MODEL : CCD-TR617E/TR717E/TR918E/TRV57E/TRV67E/TRV87E HI CONTROL(HI BLOCK) 2SC4738F...
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E VC-234 (CAMERA, Y/C PROCESSOR, FOCUS/ZOOM MOTOR DRIVE, REC/PB AMP, LINE IN/OUT, MODE CONTROL, SERVO, HI CONTROL, AUDIO) PRINTED WIRING BOARD — Ref. No. VC-234 Board; 1,000 Series — For printed wiring board • Refer to page 4-91, 92 for location.
Page 83
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E CAMERA, Y/C PROCESSOR, FOCUS/ZOOM MOTOR DRIVE, REC/PB AMP, LINE IN/OUT, MODE CONTROL, SERVO, HI CONTROL, AUDIO 4-37 VC-234...
Page 84
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E CF-66 (USER CONTROL) PRINTED WIRING BOARD — Ref. No. CF-66 Board; 3,000 Series — For printed wiring board CF-66 (TR model) • Refer to page 4-92 for location. (USER CONTROL) • Chip parts Transistor Diode There are few cases that the part printed on this diagram isn’t mounted in this model.
Page 85
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E USER CONTROL 4-41 4-42 CF-66...
Page 86
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E CF-67 (USER CONTROL) PRINTED WIRING BOARD — Ref. No. CF-67 Board; 4,000 Series — For printed wiring board • Refer to page 4-93 for location. • Chip parts Transistor Diode There are few cases that the part printed on this diagram isn’t mounted in this model.
Page 87
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E USER CONTROL 4-45 4-46 CF-67...
Page 88
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E For Schematic Diagram • Refer to page 4-39 for printed wiring board. CF-66 BOARD TR MODEL : CCD-TR317E/TR417E/TR427E/ (TR MODEL) TR617E/TR717E/TR918E USER CONTROL BL MODEL : CCD-TR918E DIGITAL EFFECT MODEL : CCD-TR918E -REF.NO.:3000 SERIES- XX MARK:NO MOUNT R001...
Page 89
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E For Schematic Diagram • Refer to page 4-43 for printed wiring board. CF-67 BOARD (TRV MODEL) CN004 USER CONTROL XVC_SCK XVC_SCK XCS_LCD_DA -REF.NO.:4000 SERIES- XCS_LCD_DA VC_SO XX MARK:NO MOUNT VC_SO R043 REG_GND R001 EVF_XVD PANEL_XVD PD-117 BOARD C-SYNC...
FB253 MA111-TX D256 D002 D004 D006 R005 R011 TR MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E (ABBREVIATION) TRV MODEL : CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E AUS : Australian MODEL VTR REC MODEL : CCD-TRV87E:E,HK,AUS,CN,JE HK : Hong Kong MODEL LASER LINK MODEL : CCD-TR918E/TRV87E CN : Chinese MODEL...
Page 92
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E PJ-99/100 (AV IN/OUT) PRINTED WIRING BOARD — Ref. No. PJ-99/100 Board; 4,000 Series — For printed wiring board • Refer to page 4-93 for location. • Chip parts Transistor Diode There are few cases that the part printed on this diagram isn’t mounted in this model.
Page 93
TR918E/TRV37E/TRV48E/TRV57E: :NO FILTER MODEL location where L001,L002,L003,L004 AEP,EE,NE,RU,UK/TRV67E:AEP, are printed. EE,NE,RU,UK/TRV87E:AEP,EE,NE, RU,UK (ABBREVIATION) NO FILTER MODEL : CCD-TR317E/TRV47E/ AUS : Australian MODEL TRV67E:E,HK,AUS,CN,JE/ HK : Hong Kong MODEL TRV67E:E,HK,AUS,CN,JE/ CN : Chinese MODEL TRV87E:E,HK,AUS,CN,JE : Tourist MODEL : East European MODEL...
Page 94
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E SE-100/101 (STEADY SHOT) PRINTED WIRING BOARD — Ref. No. SE-100/101 Board; 6,000 Series — For printed wiring board • Refer to page 4-93 for location. There are few cases that the part printed on this diagram isn’t mounted in this model.
Page 95
100uH R459 2520 R456 C465 C461 (HEADPHONE) L453 100uH 2012 2520 VDR452 VDR451 TR MODEL : CCD-TR317E/TR417E/TR427E/TR617E/ C466 STEREO MODEL TR717E/TR918E R461 SIGNAL PATH TRV MODEL : CCD-TRV37E/TRV47E/TRV48E/TRV57E/ LND451 TRV67E/TRV87E SEIDEN STEADY SHOT MODEL : CCD-TR617E/TR717E/TR918E/TRV57E/ TRV67E/TRV87E AUDIO STEREO MODEL...
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E VL-28/29 (VIDEO LIGHT) PRINTED WIRING BOARD — Ref. No. VL-28/29 Board; 7,000 Series — VL-28 BOARD (TR MODEL) (VIDEO LIGHT MODEL) VL-29 BOARD (TRV MODEL) (VIDEO LIGHT MODEL) VIDEO LIGHT -REF.NO.:7000 SERIES- XX MARK:NO MOUNT Q151 R :CAMERA REC...
Page 97
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ Ver 1.1 2000. 11 TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E MA-374/375 (MIC AMP) PRINTED WIRING BOARD — Ref. No. MA-374/375 Board; 3,000 Series — PLAYER/VTR For printed wiring board CD-239 (TR model) VF-129 (B/W EVF) CD-240 (TRV model) • Refer to page 4-94 for location.
Page 98
IC322 C322 2SB1218A C356 C360 0.047u 100p R347 TR MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E R333 R335 MIC AMP 4700 TRV MODEL : CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E IC322 STEREO MODEL : CCD-TR918E/TRV87E NJM2118V-T MONAURAL MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E MONAURAL MODEL MIC AMP 4-67 4-68 MA-374/375 (1/2)
Page 99
L301 is mounted. LASER LINK (CN BLOCK) EXT_MIC_DET TO(1/2) LASER LINK MODEL : CCD-TR918E/TRV87E MIC_R -REF.NO.:3000 SERIES- TR MODEL : CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E MIC_L XX MARK:NO MOUNT TRV MODEL : CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E SHOE_MIC_L EXCEPT LASER LINK MODEL LASER LINK MODEL CN303 REG_GND...
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E For Schematic Diagram • Refer to page 4-71 for printed wiring board. • Refer to page 4-90 for waveforms. PD-117 BOARD(1/2) TRV MODEL : CCD-TRV37E/TRV47E/TRV48E/TRV57E/ FB5503 TRV67E/TRV87E (TRV MODEL) L5504 10uH RGB LCD DRIVER, C5509 C5527 3.3u C5514 TIMING GENERATOR 0.01u B...
Page 103
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E For Schematic Diagram • Refer to page 4-71 for printed wiring board. • Refer to page 4-90 for waveform. FP-52,FP-152,FP-155 FLEXIBLE BOARD are replaced as a block. PD-117 BOARD(2/2) (TRV MODEL) So that those PRINTED WIRING BOARD is omitted.
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E For Schematic Diagram • Refer to page 4-90 for waveforms. VF-129 BOARD T902 B/W EVF -REF.NO.:3000 SERIES- XX MARK:NO MOUNT NO MARK:REC/PB MODE R :REC MODE Q904 2SD1819A-QRS-TX P :PB MODE VIDEO DRIVE -12.3 L902 R918 33uH 4700 ±...
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E SECTION 5 ADJUSTMENTS Before starting adjustment EVR Data Re-writing Procedure When Replacing Board The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.
1-1. Adjusting items when replacing main parts and boards. • Adjusting items when replacing main parts When replacing main parts, adjust the items indicated by in the following table. Replaced parts Block replacement Parts replacement Adjustment Adjustment Section Initialization of D, Initialization of D, E, F, 7 page data E, F, 7 page data Hall adj.
Page 118
• Adjusting items when replacing a board or EEPROM When replacing a board or EEPROM, adjust the items indicated by in the following table. *1: TRV model (CCD-TRV37E/TRV47E/TRV48E/TRV57E/ Replaced parts TRV67E/TRV87E) only. Board *2: STEREO model (CCD-TR918E/TRV87E) only. replacement *3: STEADY SHOT model (CCD-TR617E/TR717E/TR918E/ TRV57E/TRV67E/TRV87E) only.
5-1. CAMERA SECTION ADJUSTMENT 1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope • Regulated power supply • Digital voltmeter Ref. No. Name Parts Code Usage Auto white balance adjustment/check Filter for color temperature correction (C14) J-6080-058-A White balance adjustment/check ND filter 1.0...
Note2: When performing only the adjustments, the lens block and boards Pattern box need not be disassembled. Note3: TR model / TRV model TR model: CCD-TR317E/TR417E/TR427E/TR617E/TR717E/ TR918E TRV model: CCD- TRV37E/TRV47E/TRV48E/TRV57E/ TRV67E/TRV87E Connect the equipment for adjustments according to Fig. 5-1-3, 1.5 m...
Page 121
TRV model (CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E) * 1: Press the battery switch of the battery terminal using adhesive tape, etc. * 2: CCD-TRV87E model only. * 3: CCD-TRV57E/TRV67E/TRV87E model only. Color monitor Vector scope Regulated power supply ( * 1) Terminated at 75 Ω (8.4 ±...
Page 122
TR model (CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E) * 1: Press the battery switch of the battery terminal using adhesive tape, etc. * 2: CCD-TR918E model only. * 3: CCD-TR617E/TR717E/TR918E model only. Color monitor Vector scope Regulated power supply ( * 1) Terminated at 75 Ω...
1-1-3. Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette. POWER switch (MA-374/375 board) ....CAMERA DISPLAY (CF-66/67 board) (Note3) ....... ON NIGHT SHOT switch (Lens block) ......... OFF FOCUS switch (MR-8500 block) ......MANUAL VIDEO LIGHT switch (MA-374/375 board) (Note1) ..
1-2. INITIALIZATION OF D, E, F, 7 PAGE DATA 3. D Page Table Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the D, E, F, 7 Page Data”.) 1. Initializing the D, E, F, 7 Page Data Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F, 7 Page Data”.) Note 1: If “Initializing the D, E, F, 7 Page Data”...
Page 125
D page Address Address Remark Remark Initial value Initial value Fixed data-2 Fixed data-1 (Modified data. Copy the data built in (Initialized data) the same model.) Fixed data-1 Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 Fixed data-2 (Modified data.
Page 126
4. F Page table Address Remark Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the D, E, F, Initial value 7 Page Data”.) Auto white balance adj. Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F, 7 Page Data”.) Fixed data-1 Address...
Page 127
F page Address Address Remark Remark Initial value Initial value Fixed data-1 Fixed data-1 1.5MHz deviation adj. (Initialized data) 1.7MHz deviation adj. BPF f adj. IR video deviation Adj. IR audio deviation Adj. IR video carrier freq. Adj. Fixed data-2 Fixed data-2 Fixed data-1 (Modified data.
Page 128
5. E Page Table Address Remark Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the D, E, F, 7 Initial value Page Data”.) Fixed data-1 Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F, 7 (Initialized data) Page Data”.) Address Remark...
Page 129
E page Address Address Remark Remark Fixed data-1 Fixed data-1 Fixed data-2 (Initialized data) Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 Fixed data-2 Fixed data-2 Fixed data-1 (Modified data.
Page 130
Address Address Remark Remark Fixed data-1 Fixed data-2 (Initialized data) (Modified data. Copy the data built in the same model.) Fixed data-1 Fixed data-2 Fixed data-2 Fixed data-1 Fixed data-1 (Initialized data) (Initialized data) Fixed data-2 Fixed data-2 Fixed data-1 Fixed data-1 (Initialized data) (Initialized data)
6. 7 Page Table Address Remark Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the D, E, F, 7 Initial value Page Data”.) Fixed data-1 Fixed data-2: Modified data. (Refer to “2. Modification of D, E, F, 7 (Initialized data) Page Data”.) Fixed data-2 Address...
Page 132
Address Address Remark Remark Initial value Initial value Fixed data-2 Fixed data-1 (Modified data. Copy the data built in (Initialized data) the same model.) Fixed data-1 (Initialized data) Fixed data-2 Fixed data-1 (Initialized data) Fixed data-2 (Modified data. Copy the data built in the same model.) Fixed data-1 Fixed data-2...
1-3. CAMERA SYSTEM ADJUSTMENTS Before perform the camera system adjustments, Check that the specified value of “28MHz Origin Oscillation Adjustment”, “Y OUT level Adjustment” and “C OUT level Adjustment” of “VIDEO SYSTEM ADJUSTMENT” are satisfied. 1. HALL Adjustment For detecting the position of the lens iris, adjust the hall AMP gain and offset.
2. Flange Back Adjustment (Using Minipattern Box) The inner focus lens flange back adjustment is carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing. Adjusting method: 1) Install the minipattern box so that the distance between it and Subject Siemens star chart with ND filter for the front of the lens of the camcorder is less than 3cm.
3. Flange Back Adjustment 3-2. Flange Back Adjustment (2) (Using Flange Back Adjustment Chart and Subject Perform this adjustment after performing “Flange Back Adjustment More Than 500m Away) (1)”. The inner focus lens flange back adjustment is carried out Subject Subject more than 500m away automatically.
4. Flange Back Check 5. Picture Frame Setting Subject Siemens star Subject Color bar chart (2.0 m from the front of the lens) (Color reproduction adjustment frame) (Luminance : approx. 200 lux) (1.5m from the front of the lens) Measurement Point Check operation on TV monitor Measurement Point Video output terminal...
Burst position 760H TYPE P model: CCD-TR918E 510H 1/4 inch model: CCD-TR617E/TR717E/TRV57E/TRV67E 510H 1/6 inch model: CCD-TR317E/TR417E/TR427E/TRV37E/TRV47E/TRV48E Switch setting: NIGHT SHOT ..............OFF DIGITAL ZOOM (Menu display) ........OFF STEADY SHOT (Menu display) ........OFF VIDEO LIGHT ..............OFF Adjusting method: Select page: 0, address: 01, and set data: 01.
7. Auto White Balance & LV Standard Data Input Subject Clear chart (Color reproduction adjustment frame) Adjustment Page Adjustment Address 3C to 41 Note1: This adjustment should be carried out upon completion of “6. Color Reproduction Adjustment”. Note2: Check that the data of page: 6, address: 02 is “00”. If not, turn off the power and turn on again.
9. White Balance Check 10. Steady Shot Check (CCD-TR617E/TR717E/TR918E/TRV57E/TRV67E/ Subject Clear chart TRV87E) (Color reproduction adjustment frame) Precautions on the Angular Velocity Sensor Replacement Filter Filter C14 for color temperature There are two types of repair parts. correction Type A ENC03JA ND filter 1.0 and 0.4 and 0.1 Type B...
1-4. MONOCHROME ELECTRONIC VIEWFINEDER 1-4-2. Centering Adjustment SYSTEM ADJUSTMENT Mode Playback Signal Alignment tape : 1-4-1. Horizontal Slant Check For checking operation Mode Playback (WR5-5CSP) Monoscope section Signal Alignment tape : For checking operation Specified Value ± 4% (WR5-5CSP) Monoscope section Adjusting method: Use the centering adjustment ring and adjust so that the left, Specified Value...
1-4-4. Aberration Adjustment 1-4-5. Horizontal Amplitude Adjustment (VF-129 board) Mode VTR stop Mode Playback Signal Dot pattern Signal Alignment tape : 2 × a1 For checking operation Specified Value 0.8 × a2 (WR5-5CSP) Monoscope section Adjusting method: Adjusting Element C909 (SOL901) 1) Adjust the aberration adjustment ring so that the tracing of the Specified Value 10 ±...
1-5. LCD SYSTEM ADJUSTMENT 1. LCD Initial Data Input (CCD-TRV37E/TRV47E/TRV48E/TRV57E/ Mode Camera TRV67E/ TRV87E) Subject Arbitrary Adjustment Page Note1: The back light (fluorescent tube) is driven by a high voltage AC Adjustment Address A8 to AB, C4 to D2, E3 to ED, EF to F3 power supply.
2. VCO Adjustment (PD-117 board) 3. RGB AMP Adjustment (PD-117 board) Set the VCO free-run frequency. If deviated, the LCD screen will Set the D range of the RGB decoder used to drive the LCD to the be blurred. specified value. If deviated, the LCD screen will become blackish or saturated (whitish).
4. Contrast Adjustment (PD-117 board) 5. COM AMP Adjustment (PD-117 board) Set the level of the VIDEO signal for driving the LCD to the specified Set the common electrode drive signal level of LCD to the specified value. If deviated, the screen image will be blackish or saturated value.
6. V-COM Adjustment (PD-117 board) 7. White Balance Adjustment (PD-117 board) Set the DC bias of the common electrode drive signal of LCD to the Correct the white balance. specified value. If deviated, the LCD screen color cannot be reproduced. If deviated, the LCD display will move, producing flicker and Mode Camera...
5-2. MECHANISM SECTION ADJUSTMENT Mechanism Section adjustments, checks, and replacement of mechanism parts, refer to the separate volume “8mm Video Mechanism Adjustment Manual B Mechanism ”. 2-1. OPERATING WITHOUT CASSETTE 2-2. TAPE PATH ADJUSTMENT 1) Refer to “Section 2. DISASSEMBLY” and supply the power 1.
5-3. VIDEO SECTION ADJUSTMENTS 3-1. PREPARATIONS BEFORE ADJUSTMENTS Use the following measuring instruments for video section adjustments. 3-1-1. Equipment to Required TV monitor Oscilloscope (dual-phenomenon, band width above 30 MHz with delay mode) (Unless specified otherwise, use a 10 : 1 probe.) Frequency counter Pattern generator with video output terminal...
2. DD-134 board CN933 (8P, 1.0mm)(TRV model only) 4) The video light board (VL-28/29 board) need not be connected. To remove, disconnect the following connector. (Except for CCD-TR317E/TR417E/TR427E/TRV37E/TRV47E/TRV48E) CPC lid (BT) 1. VL-28/29 board CN151 (8P, 0.5mm) The lens block (CD-239/240 board) need not be connected. To Fig.
3-1-4. Connecting the Equipments Connecting the measuring instruments as shown in Fig. 5-3-2 and perform the adjustments. Connecting the TV Monitor and Regulated Power Supply Battery terminal Main Unit TV monitor Regulated power supply 8.4 0.1Vdc VIDEO Connect when using the camera mode or playing back.
3-1-5. Alignment Tape 3-1-6. Input/Output Level and Impedance The following table lists alignment tapes which are available. Video input/output Use the tape specified in the signal column for each adjustment. Phono jack, 1 Vp-p, 75Ω, If the type of tape to be used for checking operations is not specified, unbalanced, sync negative use whichever type.
3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT 1. Initialization of D, E, F, 7 Page Data If the D, E, F, 7 page data is erased due to some reason, perform “1- 2. INITIALIZATION OF D, E, F, 7 PAGE DATA”, of “5-1. CAMERA SECTION ADJUSTMENT”...
3-4. VIDEO SYSTEM ADJUSTMENTS 2. AFC f Adjustment (VC-234 board) Adjust the pull-in range of the A/D converted clock generator during playback. Video system adjustments must be performed in the following order. Mode VTR stop [Adjusting Order] Signal No signal 28MHz origin oscillation adjustment Measurement Point Display data of page: 6, address: 02...
(The data of address: 66 should be “70” to “7F”.) CCD-TR717E/TR918E/TRV67E/TRV87E Press the PAUSE button of the adjustment remote commander. Standard8 model: CCD-TR317E/TR417E/TR427E/TR617E/TRV37E/TRV47E/ Select page: 2, address: 01, set data: 00, and press the PAUSE TRV48E/TRV57E button of the adjustment remote commander.
Insert the plug into the VIDEO terminal. Note2: Hi8 model: CCD-TR717E/TR918E/TRV67E/TRV87E Standard8 model: CCD-TR317E/TR417E/TR427E/TR617E/TRV37E/TRV47E/ TRV48E/TRV57E Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 2, address: 01, set data: 41, and press the PAUSE button of the adjustment remote commander.
Processing after completed adjustment only for for the PLAYER model: Note: PLAYER model: Select page: 0, address: 01, and set data: 01. CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ Only for the PLAYER model, select page: D, address: 14, and TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/ set the data memorized at step 2) of “Preparations only for the TRV87E :AEP, UK, EE, NE, RU PLAYER model”.
TRV87E: AEP, UK, EE, NE, RU Hi8 model: CCD-TR717E/TR918E/TRV67E/TRV87E Standard8 model: CCD-TR317E/TR417E/TR427E/TR617E/TRV37E/TRV47E/ TRV47E/TRV48E/TRV57E 7-1. Preparations only for the PLAYER model 1) Select page: 0, address: 01, and set data: 01. 2) Only for the PLAYER model, select page: D, address: 14, after memorizing the data, set the bit value of bit1 to “1”.
7-3. REC AFM Current Adjustment (VC-234 board) 7-4. Processing after completed adjustment only for Set the recording levels of the REC AFM signal. If the level is too the PLAYER model low, the audio S/N will be deteriorated. If too high, color beets will Select page: 0, address: 01, and set data: 01.
3-5. IR TRANSMITTER ADJUSTMENTS 2. IR Video Deviation Adjustment (VC-234 board) (CCD-TR918E/TRV87E) Mode Camera standby Subject Arbitrary Adjust using a IR receiver jig (J-6082-383-A). Measurement Point VIDEO OUT terminal of IR receiver jig Note : If the distance between the IR receiver jig and the camcorder is (Terminated at 75Ω) below 1m, cover the LASER LINK emitter with a ND filter.
3. IR Audio Deviation Adjustment (VC-234 board) Mode VTR recording Signal Audio signal : 400Hz, –7.5dBs : L or R of AUDIO terminal Video signal : No signal : VIDEO terminal Measurement Point AUDIO L terminal and AUDIO R terminal of IR receiver jig (Terminated at 47kΩ) Measuring Instrument Audio level meter...
3-6. STEREO AUDIO SYSTEM ADJUSTMENT (CCD-TR918E/TRV87E) [Connecting the measuring instruments for the audio] • Perform the adjustment using color bar signal as a video signal Connect the audio system measuring instruments in addition to the input for the VIDEO terminal. video system measuring instruments as shown in Fig.
1. Deviation Adjustment 1-3. 1.5 MHz Deviation Adjustment (VC-234 board) Sets the spectrum of the L-ch ((L+R)/2 signal) level modulated 1-1. Connections during recording. If deviated, the crosstalk signal of the audio signal Connect TP24, TP25 and TP26 of the AFM DEV jig to CN982 will occur and the audio level will drop during both playback and of the VC-234 board.
1-4. 1.7 MHz Deviation Adjustment (VC-234 board) 2. BPF f0 Adjustment (VC-234 board) Sets the spectrum of the R-ch ((L-R)/2 signal) level modulated during Sets the BPF passing frequency so that the AFM signal can separate recording. If deviated, the crosstalk signal of the audio signal will from the playback RF signal properly.
3-7. MONAURAL AUDIO SYSTEM ADJUSTMENT 1. 1.5 MHz Deviation Adjustment (VC-234 board) Adjust to the optimum audio FM signal deviation. (CCD-TR317E/TR417E/TR427E/TR617E/ If the adjustment is not correct, its playback level will differ from TR717E/TRV37E/TRV47E/TRV48E/TRV57E/ that of other units. TRV67E) Mode...
5-4. SERVICE MODE 4-1. ADJUSTMENT REMOTE COMMANDER 2. Precautions Upon Using the Adjustment Remote Commander The adjustment remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The Mishandling of the adjustment remote commander may erase the correct adjustment data at times.
4-2. DATA PROCESS The calculation of the DDS display and the adjustment remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data.
4-3. SERVICE MODE Note: After the completion of the all adjustments, cancel the service mode by either of the following ways. 1) Unplug the main power supply and remove the lithium battery. (In this case, date and time and menu setting have been set by users are canceled.
2. Emergency Memory Address 2-1. EMG code (Emergency code) The codes shown in the following table which correspond to errors that occur are recorded in addresses 10, 14, and 18. Page F Address 10 to 1B Code Type of Emergency Address Contents No error...
2-2. MSW codes • The lower parts of the data of addresses 12, 16 and 1A represent the MSW codes (mode switch, mechanism position) when errors occurs. • The upper parts of the data of addresses 12, 16 and 1A represent, when the mechanism position is to be moved, the MSW codes at the start of movement (when moving the loading motor).
3. Bit Value Discrimination Bit values must be discriminated using the display data of the Display on the Bit values adjustment remote commander for the following items. Us the table adjustment bit3 bit2 bit1 bit0 below to discriminate if the bit value is “1” or “0”. remote commander bit7...
6. Record of Use check Page 2 Address A2 to AA Function Remarks Drum rotation Hour (H) 1000th place digit and 100th place digit of counted time (decimal digit) counted time Hour (L) 10th place digit and 1st place digit of counted time (decimal digit) (BCD code) Minute User initial power...
Note1: TR model / TRV model TR model: CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E TRV model: CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E Note2: CCD-TRV918E/TRV87E model only Note3: TRV model only Note4: Except CCD-TR317E/TR417E/TR427E/TR617E/TR717E model Note5: CCD-TR317E/TR417E/TR427E/TR617E/TR717E model only Note6: CCD-TRV87E: E, HK, AUS, CN, JE model only 9. Headphone jack check (TRV model only)
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number The components identified by mark 0 or have some differences from the original one.
Page 182
6-1-7. CASSETTE COMPARTMENT ASSEMBLY LS CHASSIS BLOCK ASSEMBLY (See page 6-9) MECHANISM CHASSIS ASSEMBLY (See page 6-10) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-7040-421-A DAMPER ASSY X-3945-399-1 GEAR ASSY, GOOSENECK 7-624-102-04 STOP RING 1.5, TYPE -E 3-947-503-01 SCREW (M1.4X2.5) X-3949-153-2 CASSETTE COMPARTMENT ASSY 3-979-686-01 WASHER, STOPPER...
Page 183
6-1-8. LS CHASSIS BLOCK ASSEMBLY S002 supplied S001 D001 FP-249 (not supplied) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-7040-419-A BASE (S) BLOCK ASSY, GUIDE 3-965-579-01 ROLLER, PINCH PRESS A-7040-418-B BASE (T) BLOCK ASSY, GUIDE 3-965-563-01 GEAR, T SOFT 3-965-559-01 STOPPER (T) 3-965-557-01 STOPPER (T), GB...
Page 184
6-1-9. MECHANISM CHASSIS ASSEMBLY M901 M903 M902 S901 supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-974-320-02 GROUND (IM), SHAFT 3-965-535-01 SPRING (LIMITTER ARM S), COIL 3-965-550-02 SCREW (M1.7X1.6) 3-965-542-01 SHIELD, MOTOR 1-657-785-11 FP-248 FLEXIBLE BOARD 3-965-539-01 GEAR (A) 3-054-404-01 SPACER, CAPSTAN 3-965-538-01 SLEEVE, MOTOR HOLDER...
Page 185
CD-239 CD-240 CF-66 6-2. ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • RESISTORS When indicating parts by reference number, parts list may be different from the parts All resistors are in ohms. please include the board name. specified in the diagrams or the components METAL: metal-film resistor used on the set.
Page 192
Ver 1.1 2000. 11 MA-374 MA-375 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R332 1-216-841-11 METAL CHIP 1/16W < SWITCH > (TR317E/TR417E/TR427E/TR617E/TR717E) R333 1-216-841-11 METAL CHIP 1/16W S301 1-692-605-11 SWITCH, SLIDE (LIGHT ON/AUTO/OFF) (TR317E/TR417E/TR427E/TR617E/TR717E) (TR617E/TR717E/TR918E) R334 1-216-831-11 METAL CHIP 6.8K...
Page 193
D302 8-719-060-65 DIODE LNA4905L01S0 D303 8-719-067-44 DIODE CL-310IRS-X-TU (TRV37E/TRV47E/TRV48E/TRV57E/TRV67E) D304 8-719-061-82 DIODE TLSU1002(TPX1,SONY) Note : Resistor is mounted to the location where L301 is printed. D305 8-719-073-01 DIODE MA111-TX The components identified by mark 0 or dotted Note : line with mark 0 are critical for safety.
Page 194
Ver 1.1 2000. 11 MA-375 PD-117 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R306 1-216-864-11 METAL CHIP 1/16W R347 1-216-838-11 METAL CHIP 1/16W (TRV87E) (TRV37E/TRV47E/TRV48E/TRV57E/TRV67E) R307 1-216-815-11 METAL CHIP 1/16W R348 1-216-837-11 METAL CHIP 1/16W (TRV37E/TRV47E/TRV48E/TRV57E/TRV67E) R349 1-216-837-11 METAL CHIP...
Page 210
〈PARTS REFERENCE SHEET〉 You can find the parts position of location of mount locations applying to VC-234 board of a set. VC-234 CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E/ TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E SIDE A IC201 IC502 IC101 — 276 —...
Page 211
FOR CAMERA COLOR REPRODUCTION ADJUSTMENT For 510H model and 760H TYPE S model Take a copy of CAMERA COLOR CCD-TR617E/TR717E/TR918E/ REPRODUCTION FRAME and TRV57E/TRV67E/TRV87E Parts referencesheets with a clear sheet for use. For 760H TYPE P model CCD-TR317E/TR417E/TR427E/ TRV37E/TRV47E/TRV48E — 277 —...
Page 213
CCD-TR317E/TR417E/TR427E/TR617E/TR717E/TR918E CCD-TRV37E/TRV47E/TRV48E/TRV57E/TRV67E/TRV87E RMT-708 AEP Model East European Model North European Model Russian Model SERVICE MANUAL CCD-TR417E/TR427E/TR617E/TR717E/ TR918E/TRV37E/TRV48E/TRV57E/ TRV67E/TRV87E UK Model 2000. 11 CCD-TR417E/TR427E/TR717E/ TR918E/TRV37E/TRV48E/ TRV57E/TRV67E/TRV87E E Model Hong Kong Model Australian Model Chinese Model CCD-TR317E/TRV47E/TRV57E/ TRV67E/TRV87E Tourist Model CCD-TRV47E/TRV57E/TRV67E/TRV87E CORRECTION-1 Correct your service manual as shown below.