Quick Start Guide
40" LED FHD TV
LT-40E710
Thank you
for purchasing your new JVC TV.
Your new TV incorporates the latest technology to enhance your viewing
experience. We would suggest that you allow about 20 mins for initial
setup.
Please follow this guide for a successful rst time installation.
1
Unpacking
Remove all packaging from the unit. Retain the packaging.
If you dispose of it please do so according to any local regulations.
TV
Screw A x 2
TV Stand Support
Screw B x 2
TV Base
Screw C x 4
Instruction Manual
Remote Control /
AAA Batteries x 2
Quick Start Guide
3
Installing the Base Stand
1. Lay the TV down on a at surface with the back side facing up, and ideally at the edge of a table so that the base of the TV slightly overhangs on it. Please
make sure a soft cushioned material (such as a pillow or thick piece of foam) is placed beneath the screen.
2. To install the TV stand, rst attach the stand support to the TV by using 2 screw A and 2 screw B. Align with the screw hole then use screws to x the stand
support to the TV.
3. To install the base stand, align the screw holes, then secure with a screw driver (not included) using the 4 screw C provided.
Screw
A
B B
2
Operating Your Remote Control
1. Press and lift the back
cover to open the battery
compartment of the
remote control.
2. Insert two AAA size
batteries. Close the
battery compartment
cover.
Install the batteries correctly by following the polarity (+ and -) indications
in the battery compartment.
screw in
TV Front
Base Stand
Front
screw in
Screw C x 4
A
4
Operating Your Remote Control
1. Connect one end of the RF coaxial cable to the aerial socket on the
wall and the other end of the cable to the RF (75 ) socket at the
rear right side of your TV.
GB
2. Connect the mains cable to the mains socket after you have
completed all the connections.
3. Switch on the POWER ON/OFF switch which is located at the front
right side under the frame. At this stage, the TV switches to standby
mode. The red LED indicator will illuminate on the front panel of
the TV.
4. In standby mode, press the
button on the right side panel of the
TV or on the remote control to turn the TV on. The red LED indicator
will turn blue.
Do not connect the TV to the mains supply until you have completed all the connections.
5
Turning the TV On for the First Time
First Time Installation
Please ensure aerial is plugged in!
Then press OK button.
1. The rst time you turn the TV on, it will go
straight into First Time Installation menu.
Press the OK button to start First Time
Installation menu.
Please select an OSD Language
English
esky
Suomi
Svenska
Slovak
Dansk
Norsk
OK
2. Press the
buttons to select your
desired language to be displayed on the
menu. The default on-screen menu language
is set as English. Press the OK button to
con rm.
Mode Select
Home Mode
Shop Mode
OK
3. Press the
buttons to select your desired
mode and then press the OK button. Press
the
button to select Yes to con rm or the
button to select No to cancel and return to
the Mode Select menu.
Well done,
your new TV is now ready to use. You will nd that there are many exciting features available. To get to know all these features, please
take some time to read the instruction manual provided with your TV.
If after reading the instruction manual you have additional questions related to the use of your TV please click on the link for Support Centre:
Norway: www.elkjop.no/service
Denmark: www.elgiganten.dk/service
To mains
2
socket
3
COMMON INTERFACE (CI)
USB
HDMI2
HDMI1(ARC)
HEADPHONE
DVB Select type
DVB-T
DVB-C
4. Press the
buttons to select DVB-T /
5. Channel tuning will commence. This operation
DVB-C and then press the OK button to
may take up to 6 minutes. The display will
con rm.
show the progress of the tuning and the
number of channels found.
Target Region Setting
Tune Type
DTV
During tuning your TV may have received signals
Germany
Italy
Netherlands
from more than one transmitter. If this has
Greece
Ireland
Norway
occurred the Target Region Setting screen will be
displayed. This will enable you to select the
Hungary
Luxembourg
Poland
correct regional transmission for the local news
MENU
service that you require.
4a. If you select DVB-T, press the
buttons
Press the
to select DTV / ATV / ATV + DTV. Press the
setting and then press the OK button to con rm.
button and then press the
buttons to select the desired country and.
Press the OK button to start tuning.
1
Country Code
2
Primary Region
DVB-C Scan Menu
3
Secondary Region
Scan type
Full
4
Tertiary Region
Frequency
610000
Auto
Network ID
Symbol(ks/s)
Auto
This will be shown as GBR for the UK.
1
OK
MENU
This will show the regional country (e.g. England,
2
4b. If you select DVB-C, the next step is to
Wales, Scotland, NI).
con gure the DVB-C system (Scan type /
3
This will allow you to set the region for your local
Frequency / Network ID / Symbol(ks/s)).
news service on BBC and ITV (e.g. London, Beds and
Press the OK button to go to the tune type
Cambs etc).
and add country select menu. This step is
4
You may receive signals from more than one
the same as the DVB-T's select the tune type
transmitter within the Secondary Region, (e.g Beds
(DTV / ATV) process. Press the
and Cambs may have Luton or Sandy Heath).
buttons to select the desired country and
then press the OK button to start tuning.
Sweden: www.elgiganten.se/service
Finland: www.gigantti. /huolto
RF Coxial Cable
(not included)
1
PC IN
RF
PC AUDIO
Channel Tuning
DTV
: 3 Channel(s)
Radio : 0 Channel(s)
Data
: 0 Channel(s)
36%
UHF CH
(DTV)
Press [MENU] to skip.
buttons to adjust each option's
Target Region Setting
GBR
England
London
(QSG-LT-40E710-130909V1-1)