hit counter script
Download
Share
Print this page
Watlow Series 96 Calibration Manual
  1. Manuals
  2. Brands
  3. Watlow Manuals
  4. Temperature Controller
  5. Series 96
  6. Calibration manual

Watlow Series 96 Calibration Manual

1/16 din temperature controller with custom toolbar
Hide thumbs Also See for Series 96:

Advertisement

Quick Links

Calibration Manual
1/16 DIN Temperature Controller
January 1999
(1627)
Series 96
with Custom Toolbar
Watlow Controls
1241 Bundy Blvd., P.O. Box 5580, Winona, Minnesota USA 55987-5580
Phone: (507) 454-5300, Fax: (507) 452-4507 http://www.watlow.com
(patent pending)
97
TOTAL
CUST T O O M M ER
CUS
ER
S S A A TISF
TISFA A CTI
CTIO O N N
3 Y ear Warranty
ISO 9001
Registered Company
Winona, Minnesota USA
Made in the U.S.A.

Advertisement

loading

Related Manuals for Watlow Series 96

Summary of Contents for Watlow Series 96

  • Page 1 CTIO O N N 3 Y ear Warranty ISO 9001 Registered Company Winona, Minnesota USA Watlow Controls 1241 Bundy Blvd., P.O. Box 5580, Winona, Minnesota USA 55987-5580 Phone: (507) 454-5300, Fax: (507) 452-4507 http://www.watlow.com January 1999 Made in the U.S.A. (1627)

  • Page 2: Table Of Contents

    Technical Assistance If you encounter a problem with your Watlow controller, see the Trouble- shooting Table in the Appendix of the Series 96 User’s Manual and review all of your configuration information to verify that your selections are consistent with your application: inputs; outputs; alarms; limits; etc. If the problem persists after checking the above, you can get technical assistance from your local Watlow representative, or by dialing (507) 454-5300, ext.

  • Page 3: Calibrating The Series 96

    Calibrating the Series 96 Warm up the unit (20 minutes). To enter a calibration menu, enter the Factory Page by holding down the ˆ and ‰ keys for six seconds. Once in the Factory Page [Fcty] use the Up-arrow ¿ or Down-arrow ¯...

  • Page 4: Thermocouple Input Procedure

    Precision millivolt source, 0 to 50mV minimum range, 0.002mV resolution. Input 1 Setup and Calibration 1. Connect the correct power supply to terminals 8 and 9 (see Series 96 User’s Manual). 2. Connect the millivolt source to terminals 6 (-) and 7 (+) with copper wire.

  • Page 5: Voltage Process Input Procedure

    Precision voltage source, 0 to 10V minimum range, with 0.001V resolution. Input 1 and 2 Setup and Calibration 1. Connect the correct power supply to terminals 8 and 9 (see Series 96 User’s Manual). Input 1 2. Connect the voltage source to terminals 4 (+) and 6 (-) of the controller.

  • Page 6: Process Output Procedures

    Precision volt/ammeter with 3.5-digit resolution. Output 1 Setup and Calibration 1. Connect the correct power supply to terminals 8 and 9 (see Series 96 User’s Manual). Milliamperes 2. Connect the volt/ammeter (set to milliamperes) to terminals 13 (+) and 14 (-).
  • Page 7 Output 4 Setup and Calibration 1. Connect the correct power supply to terminals 8 and 9 (see Series 96 User’s Manual). Milliamperes 2. Connect the volt/ammeter (set to milliamperes) to terminals 20 (-) and 21 (+). 3. At Output Calibration 4, 4mA [4``4] (Process Output Calibration Menu) enter the reading from the ammeter.

  • Page 8: Calibration Parameters

    Series 96 Factory Page Calibration Parameters The resting-state display shows one of the following sets of data, depending on controller setup. The first prompt appears in the top display, the second in the bottom. To enter the calibration mode, first enter the diagnostics mode; send value 1789 to register 1512.
  • Page 9 [hide]. bration for input 2 process. **These parameters are not available if the ramping software option has been ordered (96 _ _ - _ _ _ _ - AA _ _ ) Watlow Series 96 Calibration...
  • Page 10 Active if output 4 is process (96 _ tion 4, 4mA _- _ _ _ M -_ _ _ _) and Calibra- tion Lock (Lockout Menu) is not Enter the output set to [hide]. value in milliamps as measured. Calibration Watlow Series 96...

  • Page 11: Ordering Information

    = Universal Retransmit, range selectable: 0-20mA, 4-20mA, 0-5VÎ (dc), 1-5VÎ (dc), 0-10VÎ (dc) Software/Preset Parameters = Standard software AA = Ramping Display/Overlay Upper/Lower RR = Red/Red display GR = Green/Red display RG = Red/Green display GG = Green/Green display Watlow Series 96 Calibration...

  • Page 12: How To Reach Us

    Mission Warranty Statement: The Watlow Series 96 is warranted to be free of defects in material and workmanship for 36 months after delivery to the first purchaser for use, Watlow Controls will be providing that the units have not been misapplied. Since Watlow has no the world’s best...