Page 1
XES-Z50 3 7 63 1515 0 SERVICE MANUAL E Model Ver 1.1 2001.09 • This set consists of the following units. Model Name Using Similar Mechanism CHANGER UNIT CD Mechanism Type MG-110ES-132 CONTROL UNIT Optical Pick-up Name KSS-400A WIRELESS REMOTE COMMANDER (RM-X67)
Page 2
LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS u163 AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY. – 2 –...
http://www.xiaoyu163.com 3 7 63 1515 0 TABLE OF CONTENTS SERVICING NOTES DIAGRAMS 1-1. Connection at Repair ............ 7-1. IC Pin Function Description ......... 1-2. Front Panel Setting ............7-2. IC201 (BA6247FP-Y) Motor Driver IC Operation ..76 1-3. Removal of Front Panel at Power Off ......7-3.
http://www.xiaoyu163.com SECTION 1 SERVICING NOTES 3 7 63 1515 0 1-1. CONNECTION AT REPAIR 1-2. FRONT PANEL SETTING In repairing this set, connect as follows. In repairing the front panel, make a setting through the procedure give below. Notes: regulated dc CN501 power supply 1.
http://www.xiaoyu163.com SECTION 2 This section is extracted from instruction manual. GENERAL 3 7 63 1515 0 L 13942296513 u163 – 5 – http://www.xiaoyu163.com...
http://www.xiaoyu163.com SECTION 4 3 7 63 1515 0 MECHANICAL ADJUSTMENT 2. Fit the rack assembly putting it in the arrow A direction. At 4-1. ELEVATOR HEIGHT ADJUSTMENT this time insert a spacer (approx. 1 mm thickness) or fit the rack assembly while pushing the EV chassis assembly in the This adjustment should be done when replacing the rack assem- arrow B direction.
http://www.xiaoyu163.com SECTION 5 TEST MODE 3 7 63 1515 0 This set have the test mode function. In the test mode, FM Auto FM AUTO SCAN/STOP LEVEL ADJUSTMENT Scan/Stop Level and AM Auto Scan/Stop Level adjustments can Setting: be performed easier than it in ordinary procedure. TUN/AUX button: FM FM RF signal Setting the Test Mode...
Page 47
http://www.xiaoyu163.com 3 7 63 1515 0 AM AUTO SCAN/STOP LEVEL ADJUSTMENT FM STEREO SEPARATION ADJUSTMENT Setting: Note: Make this adjustment after “FM AUTO SCAN/STOP TUN/AUX button : FM LEVEL ADJUSTMENT”. Setting: FM RF signal level meter TUN/AUX button: AM antenna (MAIN) terminal generator 0.01 µ...
http://www.xiaoyu163.com 3 7 63 1515 0 TRACKING OFFSET ADJUSTMENT CD SECTION Condition: This adjustment is performed with the set place hori- zontally. Notes: Connection: 1. Perform adjustments in the order given. 2. Use YEDS-18 disc (Part No.: 3-702-101-01) unless otherwise oscilloscope indicated.
http://www.xiaoyu163.com 3 7 63 1515 0 CONNECTION AND ADJUSTMENT LOCATION • TUNER Section – Control Unit (FM/AM Tuner Unit) – AM AUTO SCAN/STOP LEVEL Adjustment RV201 FM STEREO SEPARATION Adjustment RV204 FM AUTO SCAN/STOP LEVEL Adjustment RV203 front side FM NOISE FOCUS Adjustment RV205 L 13942296513 •...
BUS ON SONY bus), and FM character multiple broadcast display controller (IC802) ÒLÓ: bus on Reset signal output to the tuner controller (IC502), bus interface (IC503) (for SONY bus), and SYS RST FM character multiple broadcast display controller (IC802) ÒLÓ: reset...
Page 53
SIRCS Sircs signal input from the remote control receiver in display unit BU IN Backup power supply detect signal input from the bus interface (IC503) (for SONY bus) ACC IN Accessory power supply detect signal input terminal “L”: accessory on...
Page 54
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Function Input of acknowledge signal for key input Input of acknowledge signal to accept FUNCTION KEY ACK and EJECT keys when the power is in off status ON at “L” input Input of auxiliary input (AUX IN) on/off detection Input terminal to turn on the set AUX ON simultaneously when an external unit connected to the AUX IN terminal is turned on, if the...
Page 55
PLL chip enable signal output to the FM/AM tuner unit u163 Communication request signal output to the bus interface (IC503) (for SONY bus) UNIREQ “H”: communication request LINK OFF Bus on/off control signal output of the bus interface (for SONY bus) Not used (open) – 55 – http://www.xiaoyu163.com...
Page 56
Function UNICKI Serial data transfer clock signal input from the system controller (IC501) UNISI Serial data input from the bus interface (IC503) (for SONY bus) UNISO Serial data output to the bus interface (IC503) (for SONY bus) — Power supply terminal (+5V) AVDD —...
Page 57
Ground terminal LCD-TX Transmit data output to the display controller (IC901) UNISO Serial data output to the bus interface (IC503) (for SONY bus) LCD-RX Receive data input from the display controller (IC901) UNISI Serial data input from the bus interface (IC503) (for SONY bus)
Page 58
“L”: reset For several hundreds msec. after the power supply rises, “L” is input, then it L 13942296513 changes to “H” BU-IN Backup power supply detection signal input from the bus interface (IC503) (for SONY bus) — Ground terminal EXTAL System clock input terminal (14.745 MHz)
Page 59
Output of power on/off control signal for the back light in display unit “H”: power on LINK-OFF Bus on/off control signal output to the bus interface (IC503) (for SONY bus) “L”: bus on Output of power on/off control signal for the external device DEC-ON “H”: power on Not used (open)
Page 60
http://www.xiaoyu163.com 3 7 63 1515 0 DISPLAY BOARD IC901 HD6473048-DISP01 (DISPLAY CONTROLLER) Pin No. Pin Name Function — Power supply terminal (+5V) LED drive signal output for the TIR indicator “H”: LED on Not used Not used (open) Output of command transmission start control signal to the LCD controller for liquid crystal module The OR signal with the busy signal from LCD controller for liquid crystal module is input to the LCD-BUSY (pin 9) LCD-START...
Page 61
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Function Address signal output to the flash memory (IC931) and S-RAM (IC932) — Ground terminal Address signal output to the flash memory (IC931) and S-RAM (IC932) — Ground terminal Not used (fixed at “H”) Not used (open) Not used (open) L 13942296513...
Page 62
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Function Not used (fixed at “L”) CONTR Contrast alignment signal output to the liquid crystal module (D/A output) DIMER Back light brightness control signal output to the liquid crystal module (D/A output) AVSS —...
Page 63
Not used (open) System reset signal input from the reset signal generator (IC903) and bus interface (IC951) (for RESET SONY bus) “L”: reset For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H” XTLI...
Page 64
Serial data output to the CD text decoder (IC303) Serial data input from the CD text decoder (IC303) Serial data transfer clock signal input from the bus interface (IC951) (for SONY bus) Serial data input from the bus interface (IC951) (for SONY bus)
Page 65
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Function Guard frame sync signal input from the digital signal processor (IC501) “L”: NG, “H”: OK SENS Count sense signal input from the digital signal processor (IC501) — — Not used (open) —...
Page 66
DATA7 System reset signal input from the system controller (IC301), reset signal generator (IC903), and bus interface (IC951) (for SONY bus) “L”: reset For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”...
Page 67
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Function — Power supply terminal (+5V) Not used (open) Not used (fixed at “L”) Not used (fixed at “H”) ADD14 Address signal output to the S-RAM (IC304) ADD15 Address signal output to the S-RAM (IC304) SCOR Subcode sync (S0+S1) detection signal input from the digital signal processor (IC501) WFCK...
Page 68
http://www.xiaoyu163.com 3 7 63 1515 0 DSP BOARD IC101 CXD2711Q (DIGITAL SIGNAL PROCESSOR FOR FRONT/REAR SPEAKER) IC201 CXD2711Q (DIGITAL SIGNAL PROCESSOR FOR SUB-WOOFER SPEAKER) Pin No. Pin Name Function — Ground terminal Output of ready signal at serial data transfer to the master controller (IC301) CRDY The start cause interruption occurs by a falling edge CCNT...
Page 69
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Function Serial audio data output terminal IC101: Serial data (for front speaker) output terminal IC201: Serial data (for sub-woofer speaker) output terminal Serial audio data output terminal IC101: Serial data (for rear speaker) output terminal IC201: Not used (open) —...
Page 70
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Function MA13 MA14 Address signal output terminal Not used (open) MA15 — Ground terminal MA00 IC101: Address signal output to the D-RAM (IC102) IC201: Address signal output to the D-RAM (IC202) MA01 —...
Page 71
Serial data input from the bus interface (IC306) (for SONY bus) L 13942296513 Not used (fixed at “L”) UNICKI Serial data transfer clock signal input from the bus interface (IC306) (for SONY bus) Two-way data bus with the flash memory (IC401) — Ground terminal...
Page 72
Standby signal input terminal Fixed at “H” in this set System reset signal input from the reset signal generator (IC303) and bus interface (IC306) (for SYSRES SONY bus) “L”: reset For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H” BU-IN Backup power supply detect signal input terminal (used also to reset standby) —...
Page 73
Serial data input from the digital signal processor (IC601 CXD2710R) AVSS — Ground terminal (for A/D conversion) Bus on/off control signal input from the bus interface (IC306) (for SONY bus) “L”: bus on BUS-ON With the bus in off status, standby is cancelled by bus on falling edge 2711-CE...
Page 74
http://www.xiaoyu163.com 3 7 63 1515 0 DSP BOARD IC601 CXD2710R (DIGITAL SIGNAL PROCESSOR) Pin No. Pin Name Function AMPIN Loop filter amplifier input for the PLL Not used (fixed at “L”) AMPOUT Loop filter amplifier output for the PLL Not used (open) —...
Page 75
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Function 58 to 64 TEST Not used (open) — Ground terminal 66 to 74 TEST Not used (open) EBDIR Not used (fixed at “L”) UBDIR Not used (fixed at “L”) D.SEL1 Input terminal for data output setting serial out or parallel out (fixed at “L”) —...
http://www.xiaoyu163.com 3 7 63 1515 0 7-2. IC201 (BA6247FP-Y) MOTOR DRIVER IC OPERATION (DRIVER BOARD) The elevator up/down motor connected between pin @™ and pin !• of IC201 is as M501, and the disc load/save motor connected between pin 1 and pin !• of IC201 is as M502. When the IC port logic is pin @™...
XES-Z50 3 7 6 3 1 5 1 5 0 7-7. BLOCK DIAGRAM – CHANGER UNIT (CD Section (2/2)) – • Signal path. D-RAM CONTROLLER : CD PLAY IC401 DIGITAL D OUT DATA, DATA, BCLK DATA DATAI (Page 84)
Page 106
http://www.xiaoyu163.com 3 7 63 1515 0 • IC Block Diagram – MAIN Board – IC503 MM1175XF-T1 BUS ON RESET RESET RESET SWITCH BUS ON BATT BATT SWITCH BATT VREF CHECK DATA DATA IN IN/OUT DATA OUT IC516 AT24C08N-10SI-SL383B IC515 NM24C04EM8-FL63 START CYCLE H.V.
Page 113
http://www.xiaoyu163.com 3 7 63 1515 0 IC502 SN74HC74ANS IC951 MM1284XFFE 13 12 11 BUS ON OUT BUS ON INPUT BUS ON LINK OFF BUS CLK CLK OUT VREF BUS DATA DATA OUT DATA IN 1 2 3 4 5 6 RESET BUS RESET RESET...
Page 114
http://www.xiaoyu163.com 3 7 63 1515 0 – DSP Board – IC102, 202 HM51W4260CLTT-7 IC302 AT24C32N-10SI-TR START/ STOP LOGIC H.V. ADDRESS BUS I/O BUS SERIAL PUMP/ LOAD DEVICE CONTROL TIMING COMP 256K MEMORY ADDRESS LOGIC ARRAY MAT DECODER COMPARATOR I/O BUFFER I/O BUS AND DATA SELECTOR...
http://www.xiaoyu163.com SECTION 8 3 7 63 1515 0 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark ! or dotted line with mark ! are are seldom required for routine service.
Page 119
http://www.xiaoyu163.com 3 7 63 1515 0 (2) CD CHANGER MAIN SECTION-2 JK3011, 3021, 3031 JK3012, 3022, 3032 supplied with JK3011, 3021, 3031 supplied with JK3021, 3022, 3032 L 13942296513 supplied with JK2012 supplied with JK2011 JK2012 JK2011 Ref. No. Part No. Description Remark Ref.
Page 120
http://www.xiaoyu163.com 3 7 63 1515 0 (3) CD CHANGER MAIN SECTION-3 L 13942296513 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-923-342-01 SPRING (FL2), TENSION * 114 3-015-118-01 SHEET (CD INNER CHASSIS. REAR S) 3-375-501-01 DAMPER (CNG) * 115 3-015-116-01 SHEET (CD INNER CHASSIS.
Page 121
http://www.xiaoyu163.com 3 7 63 1515 0 (4) CD CHANGER MAIN SECTION-4 MG-110ES-132 KSM-400AAM not supplied L 13942296513 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 151 A-3309-668-A DRIVER BOARD, COMPLETE * 160 3-008-217-01 BRACKET (FPC) * 152 1-664-111-11 SW BOARD 1-664-155-11 RF FLEXIBLE BOARD...
Page 122
http://www.xiaoyu163.com 3 7 63 1515 0 (5) MECHANISM DECK SECTION-1 (MG-110ES-132) L 13942296513 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark u163 3-911-104-01 WASHER * 207 X-3372-963-1 COVER (MDEK) ASSY 3-013-099-01 SPRING (EJES) 3-931-995-01 SPRING (EV), TENTION X-3371-264-1 LEVER (NET) ASSY 3-931-453-01 RACK (110) 3-927-978-01 SPRING, TENSION...
Page 126
http://www.xiaoyu163.com 3 7 63 1515 0 (9) OPTICAL PICK-UP SECTION (KSM-400AAM) L 13942296513 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref.
Page 127
http://www.xiaoyu163.com 3 7 63 1515 0 (10) MASTER CONTROL UNIT not supplied not supplied F501 front panel desorption machinery 477 483 L 13942296513 tuner control section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3372-942-1 PANEL (ORNAMENT) ASSY, FRONT * 469 3-014-042-01 SHEET (RELAY PCB), INSULATING 3-008-496-01 GUIDE (BUTTON RELEASE)
http://www.xiaoyu163.com SECTION 9 CHANGER ELECTRICAL PARTS LIST 3 7 63 1515 0 NOTE: The components identified by mark F: nonflammable • Due to standardization, replacements in the ! or dotted line with mark ! are parts list may be different from the parts speci- •...
Page 152
XES-Z50 3 7 63 1515 0 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page.