GE JSP26 Installation Instructions Manual
30" electric slide-in range
Hide thumbs
Also See for JSP26:
- Owner's manual (36 pages) ,
- Use and care manual (36 pages) ,
- Use & care manual (36 pages)
Table of Contents
Advertisement
Quick Links
Installation
Instructions
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
IMPORTANT
•
instructions for local inspector's use.
IMPORTANT
•
governing codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these
instructions for future reference.
• Skill level – Installation of this appliance
requires basic mechanical skills.
• Completion time – 1 to 3 hours
• Proper installation is the responsibility of
the installer.
• Product failure due to improper installation
is not covered under the Warranty.
WARNING
be properly grounded.
FOR YOUR SAFETY:
CAUTION:
remove house fuse or open circuit breaker
before beginning installation. Failure to do so
could result in serious injury or even death.
4053P557-2
229C
31-10567-2
05-04 JR
— Save these
— Observe all
— This appliance must
— For Personal Safety
30" Electric
Slide-In Range
ANTI-TIP DEVICE
WARNING
of tipping, the appliance must be secured by
properly installed Anti-Tip bracket packed
with this appliance.
If the Anti-Tip device supplied with the range
does not fit this application, use the universal
Anti-Tip device WB2X7909.
If you pull the range out and away from the
wall for any reason, make sure the Anti-Tip
bracket is engaged when the range is pushed
back against the wall.
1 1
— To reduce the risk
WARNING
• All ranges can tip
• Injury to persons could result
• Install Anti-Tip bracket packed
with range
• See Installation Instructions
—
Advertisement
Table of Contents
Related Manuals for GE JSP26
Summary of Contents for GE JSP26
-
Page 1: Installation Instructions
Installation 30” Electric Instructions Slide-In Range Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com BEFORE YOU BEGIN ANTI-TIP DEVICE Read these instructions completely WARNING — To reduce the risk and carefully. of tipping, the appliance must be secured by... -
Page 2: Prepare To Install The Range
Installation Instructions PREPARE TO INSTALL THE RANGE FOR YOUR SAFETY: ANTI-TIP DEVICE INSTALLATION All rough-in and spacing dimensions must be Before placing range in the counter, check the met for safe use of your range. Electricity to factory location of the stability device on the back of the range. -
Page 3: Minimum Clearances
Handle (door closed). The location of the electrical outlet may *28″ FOR MODELS – JSP26, JSS26, JSC26, be changed as needed, but electricity to JSS16, RS734, RS504 the range can be disconnected at the outlet without moving the range if the outlet is **28-1/2″... -
Page 4: Prepare The Counter
JXS63WW (white), JXS64AA (almond), or 30” JXS65CC (bisque). These kits are available through your GE dealer, if the existing cutout If you have a countertop deeper than 25″ is in a counter that has a backsplash (post- and you wish to set the range further back... -
Page 5: Side Trim Extension Kit
If there is a small gap between the sides of the range and the cabinets (up to 1/4″ each Fig. 10 side), you can order a side trim extension kit, Pub, #3-A040, through the GE service center. 25” 30” NOTE: If the distance from the back wall to the front of the counter backsplash (Dimension A in Fig. -
Page 6: Electrical Connections
Installation Instructions ELECTRICAL CONNECTIONS ELECTRICAL REQUIREMENTS TO MAKE ELECTRICAL CONNECTION CAUTION: For personal safety, • Remove the junction block access cover do not use an extension cord with this (on range back). See Fig. 12A or 12B. appliance. Remove house fuse or open SOME MODELS will have a one-piece wire circuit breaker before beginning installation. -
Page 7: Power Cord And Strain Relief Installation
Installation Instructions POWER CORD AND STRAIN CONDUIT AND SQUEEZE RELIEF INSTALLATION CONNECTOR INSTALLATION • For power cord installations only (see the • For conduit installations only, purchase a next step if using conduit), assemble the squeeze connector matching the diameter strain relief in the hole. - Page 8 Installation Instructions ELECTRICAL CONNECTIONS (CONT.) 3-WIRE POWER CORD 4-WIRE POWER CORD INSTALLATION INSTALLATION WARNING: WARNING: The neutral or The neutral wire of ground wire of the power cord must be the supply circuit must be connected to connected to the neutral terminal located the neutral terminal located in the lower in the center of the terminal block.
-
Page 9: 3-Wire Conduit Installation
Installation Instructions 3-WIRE CONDUIT INSTALLATION 4-WIRE CONDUIT INSTALLATION Loosen the 3 lower terminal screws from Loosen the three lower terminal screws the terminal block. Insert the center bare from the terminal block. Remove the wire (white/neutral) tip through the bottom ground screw and ground plate and retain center terminal block opening. -
Page 10: Install The Range
Installation Instructions INSTALL THE RANGE REMOVE OVEN DOOR LEVEL THE RANGE Before installing the range, you may remove For proper cooking and baking the range the oven door to lessen the weight of the must be leveled. Do not place range in cutout unit. - Page 11 Installation Instructions Fig. 23 IMPORTANT INSTALLATION INSTRUCTIONS FOR RANGES USED WITH COUNTERTOP HEIGHTS UP TO 38″ The height of the range must be adjusted to 1” Min. Height the countertop height. For countertop heights greater than 37″, additional measurements may need to be taken as detailed below. Build the filler as shown in Fig.
- Page 12 Notes Printed in the United States...