KLV-17HR2 AEP Model SERVICE MANUAL SPECIFICATIONS Display Unit: Panel System: LCD (Liquid Crystal Display) Panel Power Requirement: 100–240 V AC; 50/60 Hz TV System: Screen Size: 17 inches Depending on your country/region selection: Approx. 43.4 cm measured B/G/H, D/K, L, I...
Page 2
Terminals: Accessories Supplied: 1 (SMARTLINK) • Remote control (RM-Y1101) (1) 21-pin Scart connector (CENELEC standard) • Size AA batteries (R6 type) (2) including audio/video input, RGB input, TV • Coaxial cable (1) output, and SmartLink interface. • Mains lead (Type C-6) (1) •...
Page 3
VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR “pinched” or contact high-wattage resistors. SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS AP- 3. Check that all control knobs, shields, covers, ground straps, PEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE- and mounting hardware have been replaced.
1-3. TU BOARD REMOVAL P-P cable Tuner bracket Two screws (+BVTT 3x8) TU board 1-4. A AND B BOARDS REMOVAL Four screws (+BVTT 3x6) Four screws (+BVTT 3x6) Core B board A board KLV-17HR2 (AEP)
PW_INPUT_CR Adjustment value of PW_INPUT_CB 4. Send “READ_PW_INPUT_Y” command from ECS. 5. Check thgat the detection value of “PW_INPUT_Y” is within the standard of the following column. <Video(composit) input detection value average on 0 IRE black full field> Item Standard ± PW_INPUT_Y KLV-17HR2 (AEP)
2-1-6. C signal AD calibration of CCP2 decode. 1. Check “MON_CON_REG 1” = 1 2. Input 70 IRE gray full field signal in video input (AV1). (TIMING_AUTO_DETECT is enable) 2. Set data as follows. <Setting data> COLOR DYNA_PICT 0 (OFF) DC_TRAN 0 (OFF) KLV-17HR2 (AEP)
6. Adjust R_BKG, B_BKG until low light adjustment value. <low light adjustment value (11000K)> KLV-15SR2 KLV-17HR2 range 0.270 0.270 1.0JND 0.279 0.278 1.0JND – – 7. Repeat step 2-1-6 until it is high and low light adjustment value. 8. Do “Color Save” KLV-17HR2 (AEP) 2-3E...
• Items marked " * " are not stocked since they are seldom required for routine service. Some delay Les composants identifiés par la marque ! should be anticipated when ordering these items. sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. KLV-17HR2 (AEP)
• All resistors are in ohms sont critiques pour la sécurité. • F : nonflammable Ne les remplacer que par une pièce portant le numéro spécifié. When indicating parts by reference number, please include the board name. KLV-17HR2 (AEP) 5-1...
Page 35
IC TC7SZ125FU(TE85R) IC1010 8-759-549-03 IC SN74LV132APWR IC3002 6-703-772-11 IC LMH6658MMX/NOPB IC3003 6-703-772-11 IC LMH6658MMX/NOPB IC3005 8-759-712-65 IC PQ070XZ01ZP IC3006 8-759-712-65 IC PQ070XZ01ZP IC3007 8-752-425-02 IC CXD3802BQ IC3008 6-703-430-01 IC MT48LC2M32B2TG-6-Y94W IC3301 6-700-227-01 IC MM1561JFBE IC3302 8-752-409-78 IC CXD2095AQ KLV-17HR2 (AEP) 5-5...
Page 36
RESISTOR R1017 1-216-805-11 METAL CHIP 1/10W RESISTOR R1018 1-216-805-11 METAL CHIP 1/10W RESISTOR R1020 1-216-864-11 SHORT CHIP RESISTOR R1022 1-216-864-11 SHORT CHIP RESISTOR R1023 1-216-864-11 SHORT CHIP RESISTOR R1024 1-216-864-11 SHORT CHIP RESISTOR R1025 1-216-864-11 SHORT CHIP KLV-17HR2 (AEP) 5-6...
Page 37
METAL CHIP 220K 5% 1/10W RESISTOR R1173 1-218-941-81 RES-CHIP 100 5% 1/16W RESISTOR R1177 1-216-864-11 SHORT CHIP RESISTOR R1178 1-216-864-11 SHORT CHIP RESISTOR R3001 1-216-809-11 METAL CHIP 100 5% 1/10W RESISTOR R3002 1-216-809-11 METAL CHIP 100 5% 1/10W KLV-17HR2 (AEP) 5-7...