Miele K 1803 SF Installation Instructions Manual
Hide thumbs
Also See for K 1803 SF:
- Operating and installation instructions (60 pages) ,
- Operating and installation instructions (64 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Miele K 1803 SF
Summary of Contents for Miele K 1803 SF
-
Page 1: Installation Instructions
Installation Instructions K 1803 SF, K 1903 SF en - CA Installation, repair and maintenance work should be performed by a Miele authorized service technician in accordance with national and local safety regulations and the provided installation instructions. -
Page 2: Caring For The Environment
Caring for the environment Disposing of the packaging Disposal of your old appliance materials Old appliances may contain materials that can be recycled. Please contract The packaging is designed to protect your local recycling authority about the the appliance from damage during possibility of recycling these materials. -
Page 3: Installation Site
Installation Installation site Have the appliance installed by a The appliance should be installed in a qualified technician, according to dry, well ventilated room. the enclosed installation instructions. Do not install the appliance: - outdoors, - in an environment with dripping WARNING water, This appliance is top-heavy and... - Page 4 Installation Important! When there is high humidity a build-up of condensation on the outer surfaces of the appliance can occur.This can cause the surfaces to corrode.To prevent this, it is advisable to install the appliance in a dry and/or an air-conditioned room with sufficient ventilation.Please ensure that doors close and seal properly after...
-
Page 5: Installation Niche
See "Niche dimensions". If in doubt, contact Miele. The side walls of the installation cavity must be plumb. Furniture/fixtures The minimum thickness of the side... -
Page 6: Stainless Steel Panels
The "Merging Kit" is available from Miele. There are many different installation options. These are limited only by the Contact Miele or your dealer for design of the kitchen. specific information about which combinations will work with your The door hinge cannot be appliance. -
Page 7: Side Panels
The "Merging Kit" will also be needed. The "Merging Kit" is available from Miele. Installation with partition without using the "Merging Kit" If there is a partition with a thickness of more than 6 "... - Page 8 Installation Adjusting the door opening angle (optional accessory) Depending on the installation site, it may be necessary to adjust the door opening angle to 90°. ^ Open the door. ^ Insert the banking pin through the holes and drive in with a hammer. The door opening angle is now limited to 90°.
- Page 9 Dimensions Door dimensions (open min. 90°) K 18X3 SF 32 " (829 mm) K 19X3 SF 38 " (982 mm)
- Page 10 Dimensions Niche dimensions K 18X3 SF 30 ½" (774.6 mm) 30" (762 mm) K 19X3 SF 36 ½" (927 mm) 36" (915 mm)
-
Page 11: Power Supply
Dimensions Power supply 1. Power supply K 18X3 SF 15" (381 mm) K 19X3 SF 18" (458 mm) Power bars or extension cords are not safe (risk of fire). Do not use them to connect the appliance to the power supply... -
Page 12: Installing The Appliance
Installing the appliance Before you begin Tools needed for installation – Cordless screwdriver Read these instructions completely and carefully. – Torx screwdriver Have the appliance installed by a – Hammer drill qualified technician, according to – Wood drills in different sizes the enclosed installation instructions. -
Page 13: Aligning The Housing Unit
Installing the appliance Aligning the housing unit Check the installation niche To ensure a safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation requirements. ^ Check the base (see "Installation"). ^ Check the dimensions of the cavity. - Page 14 Installing the appliance RemoteVision module There are transportation safety installation devices inside the appliance to (optional accessory) protect the shelves and storage compartments until installation is Always disconnect the appliance complete. Do not remove them, or from the power supply when parts may be damaged.
-
Page 15: Preparing The Installation Niche
In that case, repeat the process. If that does not correct the Keep the appliance door closed problem, contact Miele. until it is securely fastened in the niche. Tipping hazard. Because of the size and weight of the appliance, it is essential to... - Page 16 Installing the appliance Mounting Accessories The mounting accessories needed for installing the appliance into the niche are included in the packaging. Several plastic bags are included which are numbered alphabetically. The bag needed for each step will be marked with its respective letter. Two anti-tip brackets are recommended for each appliance.
- Page 17 Installing the appliance In a cabinet without a back wall ^ Now attach the installation niche to the wall. The built-in cabinet must be secured to the wall behind it with several screws. In a cabinet with a back wall ^ screw the cabinet to the wall behind it in several places using suitable mounting brackets.
- Page 18 Installing the appliance Securing an alternative anti-tip – The beam must cover the appliance by at least 2" (50.8 mm). device ^ Mark the installation height (lower edge of the beam) on the rear wall of the niche. ^ Select screws according to the thickness of the wooden beam.
-
Page 19: Sliding The Appliance Into The Installation Space
Installing the appliance ^ Plug the appliance into the power Sliding the appliance into the outlet a. installation space The plug of the appliance should be If a side-by-side installation is easily accessible after installation. desired, connect the two appliances If the plug is not accessible after the together. -
Page 20: Aligning The Appliance
Installing the appliance ^ Unscrew the height-adjustable feet Aligning the appliance until the mark on the base has ^ Align the appliance with the custom reached the indicated guide front. dimension 1 1/4" (32 mm). The guide dimension of 1 1/4" (32 mm) is related to a niche height of 84"... - Page 21 Installing the appliance Attaching the appliance to the Attaching the toe-kick cover installation niche The maximum height of the toe-kick cover is 4" (102 mm) from the top of the floor. Do not cover the ventilation slits in the plinth. Risk of damage to the appliance.
- Page 22 Installing the appliance ^ Insert the foam pieces back into the sides. ^ Position the air separator in the center of the appliance door. ^ Remove the foil from the adhesive strips. ^ Attach the toe-kick cover to the plinth. Mounting the air separator The air separator keeps the supply and exhaust air separate.
-
Page 23: Electrical Connection
If there are any questions regarding the electrical connection of this appliance to the power supply, please consult a licensed electrician or call the Miele Technical Service. U1-800-999-1360 V1-800-565-6435... -
Page 24: Remotevision (Optional Accessory)
'virtual link' between your following requirements appliance and our monitoring center. If – A wireless router that supports an a fault occurs, Miele's client service IEEE 802.11b/g protocol center will be notified and contact you, ® or another trusted individual identified –... -
Page 25: Accessing The Remotevision Control Panel
RemoteVision (optional accessory) ^ Tap the X button until ; appears in Accessing the RemoteVision the display. control panel ^ Touch the access button "p" to confirm. See the table on the following page for a description of each setting in the ^ Touch the access button "p"... - Page 26 RemoteVision (optional accessory) MasterCool control panel options for RemoteVision Status indicators Description of function Flashing ; ~ Module booting phase Flashing ; ‡ Not connected to network Flashing ; | Connection to network established, no IP address assigned Solid Connected to network Flashing ;...
- Page 29 K 1803 SF, K 1903 SF en - US, CA M.-Nr. 09 920 730 / 00...