GE JGB910 Technical Service Manual
Self-cleaning gas convection ranges
Hide thumbs
Also See for JGB910:
- Owner's manual & installation instructions (64 pages) ,
- Owner's manual (64 pages) ,
- Owner's manual and installation instructions (61 pages)
Related Manuals for GE JGB910
Summary of Contents for GE JGB910
- Page 1 GE Consumer Service Training TECHNICAL SERVICE GUIDE XL44 Self-Cleaning Gas Convection Ranges MODEL SERIES: JGB910 JGB920 PUB # 31-9046 03/00...
- Page 2 If grounding wires, screws, straps, clips, nuts, or washers used to complete a path to ground are removed for service, they must be returned to their original position and properly fastened. GE Consumer Service Training Technical Service Guide Copyright © 2000 All rights reserved.
-
Page 3: Table Of Contents
Table of Contents Table of Contents Description of Range ..................2 Installation of the Range .................. 2 Cooktop Removal ..................... 4 Conversion to L.P. (Propane) Gas ..............5 Upper Control Panel Access ................7 Lower Control Panel Access ................9 Warming Zone .................... -
Page 6: Cooktop Removal
Cooktop Removal 1. Remove electrical power to the range. Turn off gas at Grate the main valve. 2. Lift off burner grates, caps, and burner heads. 3. Remove 8 screws holding burner bases to cooktop. 4. Lift bases and graphite seals off cooktop. Burner cap Burner Burner... -
Page 7: Conversion To L.p. (Propane) Gas
Conversion to L.P. (Propane) Gas Convert Regulator - Regulator is located in the lower, left hand rear corner of the range as viewed from the front. Depending on the model, remove the storage drawer, broiler drawer or false panel to access the regulator. Some Gas Valve (Safety Valve) models with a broiler drawer will have a metal cover over... - Page 8 BAKE BURNER ADJUSTMENTS BROIL BURNER Loosen Air Adjustment ADJUSTMENTS Shutter Air Adjustment Shutter Loosen Open the bake and broil air shutter adjustments as far as possible and adjust later if necessary. Beneath the bake and broil burner orifice hoods are LP orifice needles. To convert to L.P. tighten the orifice hoods against the orifice needle until the hoods are snug (2-2½...
-
Page 9: Upper Control Panel Access
Upper Control Panel Access FLIP PANEL UP TO ACCESS Remove Control Panel FLOURESCENT LIGHT 1. Grasp the light panel cover at the rear, where it is HINGED ON hinged to the control panel. Lift upward at the rear, BACK SIDE just far enough to insert a small, thin bladed screw- REMOVE 2 SCREWS driver between the end cap and the fluorescent light... - Page 10 REINSTALLING CONTROL PANEL SPARK MODULE SPARK MODULE REINSTALLING CONTROL PANEL When reinstalling the control panel, push up The spark module is located behind the control panel on The spark module is located behind the When reinstalling the control panel, push on the vent lip with your fingers.
-
Page 11: Lower Control Panel Access
Lower Control Panel Access Remove Lower Control Panel 1. Remove electrical power to the range. Turn off gas at the main valve. 2. Remove cooktop. 3. Remove all knobs by pulling them straight off the stems. 4. Remove 4 screws (A) beside rear burner knobs. GEA00125 5. -
Page 12: Convection Oven Fan
Convection Oven Fan NOTE: The fan will not start until the preheat tem- perature is reached. In a convection oven, a fan circulates hot air over, under, and around the food. This circulating hot air is evenly distributed throughout the oven cavity. As a result, foods are evenly cooked and browned—often in less time than with regular heat. -
Page 13: Warming Drawer
Warming Drawer The warming drawer will keep hot, cooked foods at Push the serving temperature. The warming drawer cannot be right rail used during a self-clean cycle. The ON signal light is release down. located above the control knob. Remove Warming Drawer 1. -
Page 14: Special Features
Special Features – 12 –... - Page 15 – 13 –...
-
Page 16: Fault Code Memory Display
Fault Code Memory Display – 14 –... -
Page 17: Erc Failure Codes
ERC FAILURE CODES FAILURE MEANING CORRECTION CODE Stuck key pad or transistor -F0- If code cannot be cancelled, replace failure. May mean relay is -F1- control. turned on. -F7- Indicates that oven is over Look for welded relay contacts. (Heating -F2- temperature in one of the following elements on in off mode). -
Page 18: On-Board Diagnostic Tests
On-Board Diagnostic Tests – 16 –... - Page 19 – 17 –...
-
Page 20: Door Latch Mechanism
– 18 –... -
Page 21: Troubleshooting
Troubleshooting – 19 –... - Page 22 Notes – 20 –...
-
Page 23: Schematics And Strip Circuits
Schematics and Strip Circuits GEA00065 – 21 –... - Page 24 Oven Light Circuit RELAY CONTACT OPERATION TEST Shown with OVLT Oven Light On Voltage Voltage Relay Terminals in Mode in Off RK SW 120 VAC 0 VAC Bake BA to N in Bake in Off 120 VAC 0 VAC Broil BR to N in Broil in Off...
- Page 25 Warming Drawer Circuit Warming Drawer Circuit Indicator Light Infinite Switch Internal Heating Resistor 32 Ohms Heating Element 450 Watts Thermo Disc Switch 140° (Switch opens at 140¡ F) (Switch closes at 120¡ F) 120° GEA00157 Warming Zone Circuit Warming Zone Circuit Indicator Light Infinite Switch Internal Heating...
-
Page 27: Wiring Diagram
Wiring Diagram GEA00067 – 25 –... - Page 28 Notes – 26 –...
-
Page 29: Warranty Information
Any part of the range which fails due to a defect in materials or work- From the date of the manship. During this full one-year warranty, GE will also provide, free of charge, all labor and in-home service to replace original purchase the defective part. -
Page 30: Consumer Services
800.626.2000 800.TDD.GEAC (800.833.4322) to request information or service. You can have the secure feeling that GE Consumer Service will still be there after your Service warranty expires. Purchase a GE contract while your warranty is still in effect and you’ll Contracts receive a substantial discount.