EchoLife HG510 Home Gateway User Manual HUAWEI TECHNOLOGIES CO., LTD.
Page 2
Free Communication, Wonderful Life Thank you for choosing EchoLife HG510 Home Gateway of Huawei Technologies Co., Ltd. EchoLife HG510 Home Gateway User Manual Issue Product Version V100R001C05 Date 2006-10-14 202012...
Page 4
Take waterproof measures during the storage, transportation and running of the device. Before installing and using the HG510, read this manual carefully. In case of failure, this equipment must be returned to HUAWEI Authorized Service Station for servicing to ensure compliance with safety requirements.
Page 5
However, this is normal. The terminal can still work normally. About This Manual After reading this manual, you will know the functions, features, and operations of EchoLife HG510. The whole manual consists of six chapters. To know about… See…...
Page 6
Terminal Display is in Courier New. Courier New Environmental Protection This product has been designed to comply with the requirements on environmental protection. For the proper storage, use and disposal of this product, national laws and regulations must be observed. Huawei Technologies Proprietary...
EchoLife HG510 Home Gateway Chapter 1 Overview Chapter 1 Overview Thank you for purchasing the EchoLife HG510 Home Gateway device (hereinafter referred to as HG510). With HG510, you can access the Internet using your high-speed ADSL connection. This user manual will show you how to install and set up HG510.
User Manual EchoLife HG510 Home Gateway Chapter 1 Overview access the IP network through ADSL ports. Figure 1-1 shows a typical networking scheme. Carrier's OSS IADMS/CPEMS IPTV DSLAM Network Ephone Internet BRAS F igure 1-1 Networking of HG510 1.3 Appearance The following sections describe the front panel and rear panel of HG510.
Page 11
User Manual EchoLife HG510 Home Gateway Chapter 1 Overview There are several indicators on the front panel of HG510. They indicate the running status of the device. Table 1-1 describes these indicators. Table 1-1 Indicators on the front panel Label...
User Manual EchoLife HG510 Home Gateway Chapter 1 Overview 1.3.2 Rear Panel POWER ON/OFF RESET LAN4 LAN3 LAN2 LAN1 ADSL F igure 1-3 Rear Panel There are several external interfaces on the rear panel. Table 1-2 describes these interfaces. Table 1-2 Interfaces on the rear panel...
User Manual EchoLife HG510 Home Gateway Chapter 2 Installation Chapter 2 Installation 2.1 Unpacking Check Before you install HG510, check the parts according to the packing list. 2.2 Connecting HG510 You need to connect the device to the following objects:...
Page 14
User Manual EchoLife HG510 Home Gateway Chapter 2 Installation POWER ON/OFF RESET LAN4 LAN3 LAN2 LAN1 ADSL Phone Modem Port Jack Line Port Phone Port Splitter Power Phone Adapter PC1 PC2 PC3 F igure 2-1 Connecting HG510 To connect the device, follow this procedure.
Page 15
User Manual EchoLife HG510 Home Gateway Chapter 2 Installation Caution: Although you use the same type of cable, The ADSL and PHONE ports are not interchangeable. Do not route the ADSL connection through the PHONE port. Huawei Technologies Proprietary...
User Manual EchoLife HG510 Home Gateway Chapter 3 Before Using HG510 Chapter 3 Before Using HG510 3.1 Configuration Preparations To use HG510 ADSL/Ethernet router, you need to have the following: ADSL service up and running on your telephone cable, with at least one public Internet address for your LAN.
Page 17
User Manual EchoLife HG510 Home Gateway Chapter 3 Before Using HG510 If authentication succeeds, the Device Info page is displayed as shown in Figure 3-1. F igure 3-1 HG510 home page Huawei Technologies Proprietary...
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration Chapter 4 Configuration This chapter introduces the configuration of HG510 through Web, including the following contents: Advanced Setup Quick Setup 4.1 Advanced Setup Advanced Setup allows system administrator to configure the...
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration Note: If default PVC is deleted, you can set up PVC through Quick Setup. To do this, refer to “4.2 Quick Setup”. F igure 4-1 Advanced Setup – WAN This page shows the existing WAN interfaces in the system. To configure a PVC, click Add or Edit.
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration F igure 4-2 Advanced Setup – LAN Enter the IP address and subnet mask. Select Enable DHCP Server to enable the DHCP function and configure the related parameters. Alternatively, select Disable DHCP Server as required.
Page 21
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration The internal port is required only if the external port needs to be converted to a different port number used by the server on the LAN side. You can configure up to 32 port conversion rules.
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration II. DMZ Host HG510 can automatically forward the packets from the applications that do not belong to the Virtual Servers table to a DMZ host. Figure 4-5 shows the configuration page.
Page 23
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration I. Outgoing IP Filtering F igure 4-6 Advanced Setup – Firewall – Outgoing IP Filtering Setup By default, all outgoing IP traffic from the LAN is allowed, but some IP traffic will be blocked by setting up filters.
Page 24
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration If multiple conditions are specified, all conditions must be satisfied in packet filtering. Click Save/Apply to validate the settings. II. Incoming IP Filtering By default, all incoming IP traffic from the WAN is blocked when the firewall is enabled.
Page 25
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration Figure 4-9 Advanced Setup – Firewall – Add new Incoming IP Filter Click Save/Apply to validate the configuration. III. MAC Filtering MAC Filtering is only effective on ATM PVCs configured in Bridge mode.
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration F igure 4-10 Advanced Setup – Firewall – MAC Filtering Setup Click Add to create a filter to identify the MAC layer frames by specifying at least one condition below. If multiple conditions are specified, all of them take effect.
Page 27
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration I. Default Gateway As shown in Figure 4-12, if you select the Enable Automatic Assigned Default Gateway checkbox, HG510 will assign the first activated PVC from PPPoA, PPPoE, IPoA or MER/DHCP to the default gateway.
Page 28
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration II. Static Route Setup F igure 4-13 Advanced Setup – Routing – Static Route Click Add to display the Static Route Add page as shown in Figure 4-14. Enter the destination network address, subnet mask, gateway and/or available WAN interface.
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration 4.1.6 Configuring DNS You can configure the DNS server through this operation. Figure 4-15 shows the configuration page. F igure 4-15 Advanced Setup – DNS Server If the Enable Automatic Assigned DNS checkbox is...
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration Consult your Internet Service Provider (ISP) and make sure that these settings match the settings provided by the ISP. Figure 4-16 shows the configuration page. F igure 4-16 Advanced Setup – DSL Select the parameters and click Save/Apply.
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration First, you need to create mapping groups between LAN and WAN by using the Add button. The Remove button is used to delete the groups. Refer to Figure 4-17. F igure 4-18 Advanced Setup – Port Mapping – Add 4.2 Quick Setup...
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration Table 4-1 ADSL service modes Virtual Dialup Dedicated Line Pure 2684 PPPoE PPPoA bridge routing (IPoA) connecti connectio connecti connection connection PPPoE PPPoA user name user name VPI/VCI VPI/VCI VPI/VCI password...
Page 33
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration Step Action Refer To Configure ATM PVC. Select Connection type and encapsulation mode. Configure PPP username and password. III. Enable IGMP multicast and WAN service. Configure LAN Service. WAN setup-summary. I. Configure ATM PVC F igure 4-19 Quick Setup –...
Page 34
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration II. Select Connection Type and Encapsulation Mode F igure 4-20 Select Connection Type and Encapsulation Mode Select PPP over Ethernet (PPPoE) as the connection type. Select an appropriate encapsulation mode suggested by your ISP.
Page 35
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration As shown in Figure 4-21, enter the username and password of the PPP service and the PPPoE service name. Select a proper authentication mode (AUTO, PAP, CHAP or MSCHAP). For more information about the actual parameters, contact your ISP.
Page 36
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration V. Configure LAN Service F igure 4-23 Configure LAN Service Enter the IP address (192.168.1.1 by default) and the subnet mask (255.255.255.0 by default). Select Disable/Enable DHCP Server. If you enable DHCP server, configure the DHCP server parameters.
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration VI. WAN Setup – Summary F igure 4-24 WAN Setup – Summary The last page gives a summary of previous steps. Make sure that the settings match the one provided by your ISP. Then click Save/Reboot to complete the configuration procedure.
Page 38
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration Step Action Refer to Enable NAT, IGMP Multicast, and WAN service. Configure LAN service. WAN setup–summary. I. Configure ATM PVC F igure 4-25 Configure ATM PVC Enter the VPI/VCI values. For more information about the actual parameters, contact your ISP.
Page 39
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration II. Select Connection Type F igure 4-26 Select Connection Type Select IP over ATM (IPoA). Select a proper encapsulation mode in the drop-down list box. For more information about the actual parameters, contact your ISP.
Page 40
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration Configure the WAN IP Address, WAN Subnet Musk, Default Gateway and DNS. For more information about the actual parameters, contact your ISP. Click Next to go to the next step. IV. Enable NAT, IGMP Multicast, and WAN Service...
Page 41
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration V. Configure LAN Service F igure 4-29 Configure LAN Service Enter the IP address (192.168.1.1 by default) and subnet mask (255.255.255.0 by default). Select Disable/Enable DHCP Server. If you enable DHCP server, configure the DHCP server parameters.
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration VI. WAN Setup – Summary F igure 4-30 WAN Setup – Summary This page gives a summary of previous steps. Make sure that the settings match the settings provided by ISPs, and then click Save/Reboot to complete the configuration procedure.
Page 43
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration Step Action Refer to WAN setup–summary. I. Configure ATM PVC F igure 4-31 Configure ATM PVC Enter the VPI/VCI values. For more information about the actual parameters, contact your ISP. Click Next to go to the next step.
Page 44
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration II. Select Sonnection Type F igure 4-32 Select Connection Type Select Bridging, and a proper encapsulation mode. For more information about the actual parameters, contact your ISP. Click Next to go to the next step.
Page 45
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration Select Obtain an IP address automatically to enable this service. Enter a service name and check the box to enable this WAN service. Click Next to go to the next step.
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration V. WAN Setup – Summary F igure 4-35 WAN Setup – Summary The last page gives a summary of previous steps. Make sure that the settings match the settings provided by ISPs, and then click Save/Reboot to complete the configuration procedure.
Page 47
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration Step Action Refer to Enable NAT, IGMP multicast, and WAN service. Configure LAN service. WAN setup–summary. I. Configure ATM PVC Figure 4-36 Configure ATM PVC Enter the VPI/VCI values. For more information about the actual parameters, contact your ISP.
Page 48
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration II. Configure Connection Type and Encapsulation Mode Figure 4-37 Configure Connection Type and Encapsulation Mode Select MAC Encapsulation Routing and a proper encapsulation mode. For more information about the actual parameters, contact your ISP.
Page 49
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration III. Configure WAN IP Settings Figure 4-38 Configure WAN IP Settings Enter the WAN IP. If you select Obtain an IP address automatically, HG510 can get the IP address automatically from the DHCP server.
Page 50
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration If you select Use the following DNS server ad dresses, you need to enter the IP address of the DNS server manually. Click Next to go to the next step. IV. Enable NAT, IGMP Multicast, and WAN Service Figure 4-39 Enable NAT, IGMP Multicast, and WAN service Select Enable NAT and Enable Firewall as required.
Page 51
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration V. Configure LAN Service F igure 4-40 Configure LAN Service Configure the IP address and subnet mask of the LAN interface. Select Disable/Enable DHCP Server as required. If you select Enable DHCP Server, enter the related DHCP parameters.
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration VI. WAN Setup–Summary F igure 4-41 WAN Setup – Summary The last page gives a summary of previous steps. Make sure that the settings match the settings provided by ISPs, and then click Save/Reboot to complete the configuration procedure.
Page 53
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration Step Action Refer to Enable IGMP multicast and WAN service. Configure LAN service. WAN setup–summary. I. Configure ATM PVC Enter the VPI/VCI values. F igure 4-42 Configure ATM PVC Enter the VPI/VCI. For more information about the actual parameters, contact your ISP.
Page 54
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration II. Select Connection Type F igure 4-43 Select Connection Type Select PPP over ATM (PPPoA) and a proper encapsulation mode. For more information about the actual parameters, contact your ISP. Click Next to go to the next step.
Page 55
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration Enter the username and password of the PPP service. Select a proper authentication mode (AUTO, PAP, CHAP or MSCHAP). For more information about the actual parameters, contact your ISP. Click Next to go to the next step.
Page 56
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration IV. Enable IGMP Multicast and WAN Service Configuration Figure 4-45 Enable IGMP Multicast and WAN service configuration Select Enable NAT and Enable Firewall as required. Enter the service name, and selec t Enable WAN Service.
Page 57
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration Figure 4-46 Configure L AN Service Enter the IP address and subnet mask for the LAN interface. Select Disable/Enable DHCP Server as require d. If you select Enable DHCP Server, configure the related DHCP parameters.
Page 58
User Manual EchoLife HG510 Home Gateway Chapter 4 Configuration VI. WAN Setup–Summary Figu re 4-47 WAN Setup – Summary The last page gives a summary of previous steps. Make sure that settings match the set tings provided by ISPs, and then click e/Reboot to complete the configuration procedure.
User Manual EchoLife HG510 Home Gateway Chapter 5 Maintenance ter 5 Maintenance Querying formation ou can quer the configuration information of the dev ice, including: Summary WAN setting Statistics Route inform ation P settings DHCP settin Figure 5-1 the querying page.
User Manual EchoLife HG510 Home Gateway Chapter 5 Maintenance To query… Do… Summary Select Device Info > Summary to display the Device Info page. WAN settings Select Device Info > WAN to display the WAN pa LAN statistics Select Device Info > Statistics > LAN to display the LAN page.
User Manual EchoLife HG510 Home Gateway Chapter 5 Maintenance These functions can help t he system administrator to manage large amou nt of HG510 efficiently. By restoring default settings, you can set HG510 with the factory default co nfiguration. 5.2.
User Manual EchoLife HG510 Home Gateway Chapter 5 Maintenance 5.2.2 Updating Settings ou can load settings saved on the local PC to HG510. Click Update to display the Tools-Update Settings p age as shown in Figure 5-3. Click Browse to find the file containing the settings.
User Manual EchoLife HG510 Home Gateway Chapter 5 Maintenance Figure 5-4 Restoring to factory defaults 5.3 Configuring Access Control You can configure the HG510 to support ACL rules, includi Services IP Address Password 5.3.1 S ervices The Services lists the service daemons (including HTTP, ICMP, and TFTP ) that can be enabled for LAN side, WAN side or both.
User Manual EchoLife HG510 Home Gateway Chapter 5 Maintenance Figure 5-5 Management-Access Control-Services Select to enable all the WAN and LAN services Click Save/Apply to validate the settings. 5.3.2 IP Address If Access C ontrol mode is enabled, entities with the IP addresses listed in the ACL are allowed to access the local services.
User Manual EchoLife HG510 Home Gateway Chapter 5 Maintenance igure 5-6 Management-Access Control-IP Address Click Add to add IP addresses in the ACL. Enable or disable Access Control as required. To delete an IP address from the ACL, select the Remove option beside the IP addre ss, and then click Remove.
User Manual EchoLife HG510 Home Gateway Chapter 5 Maintenance Figure 5-7 Management-Access Control-Passwords As shown in Figure 5-7, select a “username” such a “admin”. Enter the old password. Enter the new password. Enter the new password again to confirm. Make sure that it is consistent with the new password.
User Manual EchoLife HG510 Home Gateway Chapter 5 Maintenance Figure 5-8 Update Software After upgrading is finished, the device will auto-reboot. Figure 5-9 Update Software After rebooting, the new version will take effect. 5.5 Configuring Diagnostics This page allows users to test the Ethernet port connection, DSL port connection, and connection to the ISP.
Page 68
User Manual EchoLife HG510 Home Gateway Chapter 5 Maintenance Figure 5-10 Diagnostics If a test display s a failure status, click Test ag ain to make sure the failure status is consistent. the t est continues to fail, click Help to f ollow the troubleshooting procedure.
User Manual EchoLife HG510 Home Gateway Chapter 6 Appendix Chapter 6 Appendix ADSL Asymmetric Digital Subscriber L Asynchronous Transfer Mode Dynamic Host Configuration Protocol Domain Name Server Digital Subscriber Line Access Multiplex Hypertext Markup Language Internet Protocols Internet Protocols Over ATM...
Page 70
User Manual EchoLife HG510 Home Gateway Chapter 6 Appendix Point to Point Protocol PPPoA PPP over ATM PPPoE PPP over Ethernet Permanent Virtual Connection Routing Information Protocol SNMP Simple Network Management Protocol Transfer Control Protocol Virtual Channel Identifier Virtual Path Identifier...
Page 71
HUAWEI TECHNOLOGIES CO., LTD. Huawei Administration Building Bantian, Longgang District Shenzhen, 518129 People’s Republic of China www.huawei.com 202012...