Related Manuals for Panasonic PT-CW331R
Summary of Contents for Panasonic PT-CW331R
- Page 1 PT-CW331R P ro d u c t N u m b e r : Ultra Short-Throw DLP ™ Projector P ro d u c t N a m e : As of June 2013. Specifications and appearance are subject to change without notice.
- Page 2 PT-CW331R Ultra Short-Throw DLP ™ Projector Specifications Main unit Power supply 100 –240 V AC, 3.6– 1.5 A, 50/60 Hz Power consumption 340 W (0.5 W when set to 6.0 W when STANDBY MODE STANDBY MODE set to NETWORK DLP™ chip Panel size 16.5 mm (0.65 inches) diagonal (16:10 aspect ratio)
- Page 3 PT-CW331R Ultra Short-Throw DLP ™ Projector COMPUTER 1 AUDIO IN M3 (L, R) × 1, 0.5 Vrms COMPUTER 2 AUDIO IN M3 (L, R) × 1, 0.5 Vrms VIDEO/S-VIDEO AUDIO IN Pin jack × 2 (L/R × 1), 0.5 Vrms AUDIO OUT M3 (L, R) ×...
- Page 4 PT-CW331R Ultra Short-Throw DLP ™ Projector Dimensions unit : mm (inch) NOTE: This illustration is not drawn to scale. (1-25/32) (13-3/16) (14-1/16) Terminals MiniUSB HDMI input Monitor output LAN connector Computer 1 input Audio input for computer 1 S-Video input...
-
Page 5: Standard Setting-Up Position
PT-CW331R Ultra Short-Throw DLP ™ Projector Standard setting-up position NOTE: Illustrations show the projector installed using optional ceiling mount bracket ET-PKV100H and bracket ∅38 (1-1/2) assembly ET-PKC200B. This illustration is not drawn to scale. (9-1/8) 102.5 Upper edge of projected image... - Page 6 PT-CW331R Ultra Short-Throw DLP ™ Projector Projection distance for 16:10 aspect ratio screen Unit: meters Screen size A: Distance from the edge B: Distance from the E: Height from the edge of F: Height from the edge of (inch, diagonal)
- Page 7 PT-CW331R Ultra Short-Throw DLP ™ Projector Installable angle Install the projector at an angle within the range shown below. • Vertical direction The projector may be installed at a vertical angle of ±10° +10° -10° • Horizontal direction The projector may be installed at a horizontal angle of ±10°...
-
Page 8: List Of Compatible Signals
PT-CW331R Ultra Short-Throw DLP ™ Projector List of compatible signals The signals that can be input to this projector are shown in the table below. Horizontal scanning fre- quencies of 15 kHz to 100 kHz, vertical scanning frequencies of 24 Hz to 120 Hz, and a dot clock of 162 MHz maximum can be input. - Page 9 PT-CW331R Ultra Short-Throw DLP ™ Projector 3D-compliant signal list The 3D signals that can be input to this projector are as follows. Display mode Display Scanning frequency Dot clock HDMI Computer1/2 Video/S-Video resolution frequency Frame Side by Top and Frame...
- Page 10 PT-CW331R Ultra Short-Throw DLP ™ Projector Basic format Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this order. Add parameters according to the details of control. C2 C3 P1 P2 ... Pn...
-
Page 11: Status Request Commands
PT-CW331R Ultra Short-Throw DLP ™ Projector Status request commands Command : Parameter Function Callback Description Main power status Standby Lamp on status Standby Lamp on control in progress Lamp on Lamp off control in progress AV mute function status Input signal status... - Page 12 PT-CW331R Ultra Short-Throw DLP ™ Projector Notes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. Never place objects on top of the projector while it is operating.
-
Page 13: Operating The Projector Continuously
PT-CW331R Ultra Short-Throw DLP ™ Projector Operating the projector continuously If the projector is to be operated continuously 22 hours or more, lamp replacement cycle duration becomes shorter. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods (one hour or less).