Page 1 Color Laser Printer EPSON ColorPage -C8200 ® SEPG99-003...
Page 2 SEIKO EPSON CORPORATION. All effort have been made to ensure the accuracy of the contents of this manual. However, should any errors be detected, SEIKO EPSON would greatly appreciate being informed of them.
Page 3 2. MAKE CERTAIN THAT THE SOURCE VOLTAGES IS THE SAME AS THE RATED VOLTAGE, LISTED ON THE SERIAL NUMBER/ RATING PLATE. IF THE EPSON PRODUCT HAS A PRIMARY AC RATING DIFFERENT FROM AVAILABLE POWER SOURCE, DO NOT CONNECT IT TO THE POWER SOURCE.
Page 4: About This Manual
About this manual This manual describes basic functions, theory of electrical and mechanical operations, maintenance and repair procedures of the EPSON EPL- C8200. The instructions and procedures included herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page.
Page 5 Abbreviation ADC = Automatic Density Control FDR = Feeder OPC = Organic Photo Conductor AG = Analog Ground FG = Frame Ground P/H = Paper Handling ASSY = Assembly FRU = Field Replaceable Unit P/R = Pressure Roll AUX. = Auxiliary GND = Ground PCDC = Pixel Count Dispense Control B/W = Black and White...
Page 6: Safety Information
Safety Information To prevent accidents during a maintenance procedure, strictly observe Power Supply the Warnings and Cautions. Do not do anything that is dangerous or not within the scope of this document. Before starting any service procedure, switch off the printer power and Do not do anything that is dangerous even if not specifically described unplug the power cord from the wall outlet.
Page 7: Mechanical Components
Mechanical Components Safety Components If you service a driving assembly (e.g., gears), first turn off the power The printer is equipped with safety components (e.g., interlock and unplug the power cord. Then manually rotate the assembly. switches, fuses, thermostat) and safety switches for protecting users and service personnel from injury and the equipment from damage.
Page 8 Exit Chute Switch This switch is a safety switch. This switch is turned off when the Exit Upper Assembly (the cover on the upper left side of the printer) is opened. P/J91 (Connector that connects the Main Harness Assembly and Registration Harness Assembly) This is an interlock connector that cuts off the power supply (24VDC, 5VDC-LD) to the control circuit and related parts.
Page 9 Laser Beam NOTE: The laser beam has a narrower frequency band and more coherent phases than any other light (sunlight, electric light). It has excellent monochromaticity and convergence. A thin The printer has two interlock switches: the Front Cover Switch R and laser beam reaches long distances.
Page 10 High Temperature Assembly Parts To prevent you from becoming injured or burned, do the following: To prevent you from becoming injured, keep the following in mind: Before working with a high temperature Assembly (e.g., Fuser When handling heavy parts (including the printer itself), use good Assembly), turn off the power, unplug the power cord and wait until it posture to protect your back whenever you lift, move or place parts.
Page 11 Consumables Improper Printer Use Some parts may cause a particulate explosion or fire if handled Modifying, revising, tampering with the printer, especially to the safety improperly. Do not handle these parts near fire or throw into a fire. mechanism, is strictly prohibited in all circumstances. Some materials (e.g., Developer or Fuser Oil) may cause bodily injury.
Page 13: Manual Contents
Manual Contents Chapter 1 Product Descriptions Chapter 2 Operating Principles Chapter 3 Disassembly and Assembly / Adjustment Chapter 4 Diagnostics Chapter 5 Troubleshooting Chapter 6 Maintenance Appendix Revision Status Revision Issued Date Description (Preliminary revision)
Page 14 PRODUCT DESCRIPTIONS...
Page 15: Table Of Contents
Table of Contents Features....................1 ROM Module Copy ................. 31 Panel Setting Initialization............... 31 Specifications ..................3 Maintenance Mode ................. 31 Basic Specifications ................3 Error Recovery Operation ............... 32 Paper Specification ................8 Panel Setting..................33 Reliability and Durability..............11 Operating Environment ..............
Page 16: Features
1.1 Features 64-bit high speed memory: SDRAM DIMM (Same as EPL-C8000) The EPSON ColorPage EPL-C8200 is a non-impact color page printer 64MB RAM standard: expandable up to 256MB (2 expansion that is designed based on the EPL-C8000. This printer is mainly slots) (Same as EPL-C8000) improved on a controller basis.
Page 17 Font registration in the PostScript3 mode 5. Full compatibility with the EPL-N2700: LJ4, GL2, 1239X, ESC/Page (monochrome) 6. Supports PostScript3 when used with an optional EPSON RIP Station XXXX or Adobe PostScrip 3 Module. 7. Used with SC6000 (optional), color copy (EPSON Color Copy Figure 1-1.
Page 18: Specifications
EPSON ColorPage EPL-C8200 Revision A 1.2 Specifications Table 1-1. Speed Mode Print mode Speed mode LT/A4 LEF B(LD)/A3 SEF This section describes specifications for this printer. Standard mode 16 PPM or more 8PPM or more Half speed mode 2.7 PPM or more 1.3PPM or more...
Page 19 EPSON ColorPage EPL-C8200 Revision A Paper handling: See Table 1-2. Table 1-2. Paper Feeding Capacity Paper source Available feeder Paper size Available paper thickness (Thickness) *1 *6 Standard Tray (MSI) 150 sheets 90 x 139.7 - 330.2 x 457.2 mm 60 - 105g/m...
Page 20 EPSON ColorPage EPL-C8200 Revision A Table 1-3. Paper Size / 2-UP Mode Availability Paper setting orientation 2UP mode Paper Size Notes Standard tray availability Standard cassette A3W cassette (MSI) Normal paper • LEF: Long edge is loaded first. • SEF: Short edge is loaded first.
Page 21 EPSON ColorPage EPL-C8200 Revision A Paper aligning: Single side aligning (front side) for all sizes Table 1-4. Face-Down Output Availability (both standard tray (MSI) and each cassette) Paper Size FD Availability Paper Size FD Availability Consumables: Normal paper Available Unavailable...
Page 22 EPSON ColorPage EPL-C8200 Revision A Table 1-5. Power Consumption Specifications • Average: 400Wh or less Operating (color) • Maximum: 1100W or less (Fuser: On) • Average: 500Wh or less Operating (B/W) • Maximum: 1100W or less (Fuser: On) • Average: 250Wh or less Standby mode •...
Page 23: Paper Specification
EPSON ColorPage EPL-C8200 Revision A 1.2.2 Paper Specification - Paper that has gone through other color laser printers, monochrome printers, and photocopiers. Paper specifications: See Table 1-6. - Pasted paper Table 1-6. Paper Specifications Paper Type Recommended paper 4024 paper (B/W), X-pression paper (color)
Page 24 EPSON ColorPage EPL-C8200 Revision A Paper source classification:See Table 1-7. Table 1-7. Paper Usability for Each Paper Source Special paper Recommended Normal Paper source Thick Envelope paper paper Postcard Labels sheet paper* Standard (MSI) tray Standard universal cassette A3W cassette*...
Page 25 EPSON ColorPage EPL-C8200 Revision A Printable area: When the standard universal cassette, Large Capacity Paper Paper whose width is 304.8mm (12”) or shorter: From the edge Unit, or 500-Sheet Paper Cassette Unit is used. Paper whose width is longer than 304.8mm (12”)*: From the point with a margin of 5mm * When loading paper whose width is more than 304.8 mm (12”),...
Page 26: Reliability And Durability
EPSON ColorPage EPL-C8200 Revision A 1.2.3 Reliability and Durability Print position accuracy: Main scan direction:Reference position (c) 2.5 mm MPBF: Sub scan direction:Reference position (a) 2.0 mm Printer including standard tray (MSI): 38,000 pages or more (95,000 images or more*) See Figure 1-5.
Page 27 EPSON ColorPage EPL-C8200 Revision A Durability: Printer: 180,000 sheets* (450,000 images) A4 LEF or 5 years, whichever comes first. Parts regularly replaced by the service is ignored. * 450,000 sheets if the printer is used for monochrome print only. In color printing, one page is formed with 4 images, and the value “180,000”...
Page 28: Operating Environment
EPSON ColorPage EPL-C8200 Revision A 1.2.4 Operating Environment Temperature: 10 to 32 C Humidity: 15% to 85% RH (without condensation) Air pressure (altitude):760 hPa or more (2500 meters or less) Levelness: Front - rear direction on the table:5mm or less (within 641mm)
Page 29: Environmental Conditions For Storage And Transportation
EPSON ColorPage EPL-C8200 Revision A 1.2.5 Environmental Conditions for Storage and 1.2.6 Electrical Specifications Transportation AC line noise temperature and Humidity:See Table 1-10. Pulse width: 50 to 1000 ns Table 1-10. Environmental Conditions 1 Pulse polarity: Temperature Humidity Guaranty Repeat:...
Page 30: Process Specifications
EPSON ColorPage EPL-C8200 Revision A 1.2.7 Process Specifications Leakage current: 100 V model: 0.5mA or less Printing method: Dry electrophotographic with 2 ingredients Using the intermediate belt transfer system 120V model: 3.5mA or less Light source: Semi-conductive laser beam 220V/240V model: 3.5mmA or less Condition: 1.5K...
Page 31: Applicable Standards
Adobe PostScript 3 Kit C83236* Waste Toner Collector S050020 NOTE: Laser power: 5mW (rated) (WASTE TONER BOX) Wavelength: 785nm 10/-15nm (at 25 C) EPSON RIP Station XXXX Fuser Oil Roll S052002 32KB Serial Interface Card C82307* Photoconductor unit (DRUM S051061 CARTRIDGE) FCCPart15 SubpartB, ClassB(ANSI 63.4/11.4D)
Page 32: Toner Cartridge
EPSON ColorPage EPL-C8200 Revision A 1.2.9.1 Toner cartridge Storage air pressure: 0 - 2,500m (0 up to 15,000 m is possible during air shipping, but the Toner Cartridge life: See Table 1-13. air pressure in the cargo room must be 0.7 hPA or more.) Table 1-13.
Page 33: Drum Cartridge
EPSON ColorPage EPL-C8200 Revision A 1.2.9.2 Drum Cartridge 1.2.9.3 Fuser Oil Roll Specifications: See Table 1-16. OIL Roll specifications: See Table 1-17. Table 1-16. Photoconductor Unit Specifications Table 1-17. Fuser Oil Roll Unit Specifications Specifications Specifications Formation Photoconductor, drum cleaner, waste toner box...
Page 34: Waste Toner Box
EPSON ColorPage EPL-C8200 Revision A 1.2.9.4 Waste Toner Box 1.2.11 Exterior Dimensions WASTE TONER BOX specifications:See Table 1-18. Exterior dimensions of the EPL-C8200 are as follows. Table 1-18. Waste Toner Box Specifications Formation Waste toner box and others Life 20,000 sheets * Dimensions (WxDxH) •...
Page 35: Controller Specifications
EPSON ColorPage EPL-C8200 Revision A 1.2.12 Controller Specifications Printer modes: CPU: R5000 (200MHz) Standard: ESC/Page-Color, ESC/Page (B/W), LJ4 (B/W), GL2 (B/W), ESCP2 (B/W), FX (B/W), 1239X (B/W) Enhancement technologies: Optional: Postscript3 (PostScript3 module, Peacock-B) AcuLaser Color Halftoning (monochrome print) Others:...
Page 36: Controller Board Jumper Settings
EPSON ColorPage EPL-C8200 Revision A 1.2.13 Controller Board Jumper Settings 1.3 Interface Specifications The controller board configuration of this printer can be set for the target The EPL-C8200 supports the following external interfaces. market (destination) as indicated below. The settings are made at factory (by jumper resistor).
Page 37: Parallel Interface Specification
EPSON ColorPage EPL-C8200 Revision A 1.3.1 Parallel Interface Specification Interface type: IEEE 1284 High-Speed Bi-directional Parallel I/F Operating modes: Compatibility, Nibble, ECP Synchronization: /STROBE pulse Connector type: 57RE-40360-830B(D7A)DDK or equivalent Plug: Amphenol equivalent Data transmission timing: Refer to Table 1-20 and Figure 1-9.
Page 38 EPSON ColorPage EPL-C8200 Revision A Table 1-22. Centronics Parallel Interface Pin Assignment Pin # Signal Names Descriptions STRBX Latch pulse used to read data. DATA is valid when the signal is LOW. DATA 1-8 DATA 8 is MSB and DATA 1 is LSB.
Page 39: Ethernet Interface
EPSON ColorPage EPL-C8200 Revision A 1.3.2 Ethernet Interface Interface type*: 10BaseT Table 1-23. Pin Configuration for the Ethernet I/F 100BaseTX Signal Name Half Duplex Full Duplex *: Switched at power on N.C. Communication protocol: N.C. 1. IPX/SPX (IPX, SPX, NCP, RIP, SAP, PrintServer, RemotePrinter, NDS, SNMP, ENPC) N.C.
Page 40: Type B Interface
EPSON ColorPage EPL-C8200 Revision A 1.3.3 Type B Interface Entity type 1. Emulation = Auto:See Table 1-24. This printer is equipped with a slot for Type B optional interface. 2. Emulation Menu = Fixed Main system type: MTP600dpi, PW774dt600doi, PRG( The entity type of the default emulation, rev.
Page 41: Control Panel
EPSON ColorPage EPL-C8200 Revision A 1.4 Control Panel This section describes the control panel of this printer and its functions. 1.4.1 Appearance and Descriptions The control panel of this printer consists of the LCD, 8 buttons, and 6 LEDs. See Figure 1-10 and Table 1-25 for the control panel appearance and its descriptions, respectively.
Page 42: Led Description
EPSON ColorPage EPL-C8200 Revision A 1.4.1.1 LED Description OneTouch Mode 2 LED (F) LCD (Liquid Crystal Display) (A) OneTouch mode 2 is enabled. The following 4 items can be set in this mode: One-line display for 20 characters (5 x 7 dot matrix) - RITech Normally displays printer status.
Page 43: Button Functions
EPSON ColorPage EPL-C8200 Revision A 1.4.2 Button Functions Menu button (L) Pressing this button activates the SelecType mode, and the On Line button (H) initial level of the mode (“Test Menu”) appears. In the SelecType When the printer is on-line, pressing this button puts the printer in mode, this button is used to select the setting menu, the primary off-line to prevent printing.
Page 44 EPSON ColorPage EPL-C8200 Revision A Enter button (O) Pressing this button generates “Status Sheet” in “Test Menu”. In OneTouch mode 1, used to select the value for “Orientation”. In OneTouch mode 2, used to select the value for “Toner Save Mode”.
Page 45: Service Functions
EPSON ColorPage EPL-C8200 Revision A 1.5 Service Functions 1.5.1 Hex Dump Mode Buttons: Form Feed + Power on Turning the printer on while pressing the specified button(s) until RAM Functions: “Hex Dump” is indicated. Received data is converted check is completed provides several service functions. The service into hex ASCII.
Page 46: Formatting The Flash Rom Module
EPSON ColorPage EPL-C8200 Revision A 1.5.4 Formatting the Flash ROM Module Termination: After initializing, the printer performs warm boot and returns to the normal states. Buttons: Alt + Item + Value + Enter + Power on 1.5.8 Maintenance Mode Functions: Clears the flash ROM module inserted in the slot A.
Page 47: Error Recovery Operation
EPSON ColorPage EPL-C8200 Revision A 1.5.9 Error Recovery Operation By pressing the specified buttons, the following functions are activated. a) CPU reset when E***** or C2000 Service call error is indicated Buttons: Alt + Menu + Item + value + Enter...
Page 48: Panel Setting
EPSON ColorPage EPL-C8200 Revision A 1.6 Panel Setting 1.6.1 Setting Methods This printer is equipped with the 2 types of panel setting functions; the 1.6.1.1 OneTouch mode OneTouch mode and SelecType mode. The OneTouch mode allow the NOTE: OneTouch mode is effective when the printer is free from any users to get directly to the specific setting items in the SelecType mode.
Page 49 EPSON ColorPage EPL-C8200 Revision A 2. Follow the next steps to operate the SelecType mode. 2-7) In the value select mode, pressing the Menu or Item button, the item select mode is brought back. 2-1) In the setting menu select mode, select the desired menu by pressing the Menu button.
Page 50: Selectype Setting Menu List
EPSON ColorPage EPL-C8200 Revision A 1.6.2 SelecType Setting Menu List Table 1-27. Panel Setting Menu List (2/8) This section contains the tables which list the SelecType setting menus. Menu Item Value The factory defaults values are shown in Bold Italic style. The menus...
Page 51 EPSON ColorPage EPL-C8200 Revision A Table 1-28. Panel Setting Menu List (3/8) Table 1-29. Panel Setting Menu List (4/8) Menu Item Value Menu Item Value Setup Menu Lang English Network Menu GW Byte 3 0 - 255 (Continued) Lang Francais...
Page 52 EPSON ColorPage EPL-C8200 Revision A Table 1-30. Panel Setting Menu List (5/8) Table 1-31. Panel Setting Menu List (6/8) Menu Item Value Menu Item Value LJ4 Menu FontSource Resident , Download, ROM A , ROM B GL2 Menu Pen0 0.05 0.35...
Page 53 EPSON ColorPage EPL-C8200 Revision A Table 1-32. Panel Setting Menu List (7/8) Table 1-33. Panel Setting Menu List (8/8) Menu Item Value Menu Item Value FX Menu Font Courier , Prestige, Roman, Sans serif, Script, Maintenance Engine Status Sheet Orator S, OCR A, OCR B...
Page 54: Details Of Menus And Settings
EPSON ColorPage EPL-C8200 Revision A *17: Indicated neither on the panel nor status sheet. Can be set in EJL. 1.6.3 Details of Menus and Settings *18: The value is automatically changed to “No” after the printer returns This section contains the EPL-C8200-specific information on the menus to an on-line status.
Page 55 EPSON ColorPage EPL-C8200 Revision A 3. Out Bin Tray Menu Selects the ejection tray. 1. MP Type Face-down: Ejects into face-down tray. Note that for certain Specifies the type of the paper set in the MP tray. paper sizes and types, the printer will force...
Page 56 EPSON ColorPage EPL-C8200 Revision A Config Menu CM Media Type Normal paper 1. RITech Opt1 Option1 Turns on/off the RITech function. For B/W printing, RITech works in Opt2 Option2 the general way for monochrome page printers. For color printing, RITech is effective in the AcuLaser Color Halftoning mode by using <Condition 2>...
Page 57 EPSON ColorPage EPL-C8200 Revision A 3) Reset through the control panel Paper Type 4) Warm-boot Plain Normal paper 5) “Standby” is set to “Disable”. Letterhead Normal paper After any of the conditions above occurs, if a half of the specified...
Page 58 EPSON ColorPage EPL-C8200 Revision A NOTE: The remaining level of each toner is evaluated based on the Parallel Menu dispense time of each toner cartridge. According to the dispense time, which is stored on the engine side, the 1. Buffer Size engine generates such an error as “Toner Out”.
Page 59 EPSON ColorPage EPL-C8200 Revision A Network 1. Engine Status Sheet Normal: Buffer size = 512 KB + 2% of the expanded Pressing the Enter button lets the printer print Engine Status Sheet. memory size lf language data is still in the printer, the sheet will eject. Make sure...
Page 60: Ram Expansion
EPSON ColorPage EPL-C8200 Revision A 1.6.4 RAM Expansion This printer generates the following errors when it detects insufficient memory condition. “Mem Overflow”, “Image Optimum”, “Need Memory” In this case, try taking any of the actions below. For B/W print, lower the resolution to 300 dpi.
Page 61 OPERATING PRINCIPLES...
Page 62 Table of Contents Print Process ..................1 Fusing-I ................... 35 Fusing-II ..................37 Print Process Overview..............1 Paper Exit ..................39 Print Process - Major Components ........... 2 Drives....................40 Print Process Description..............3 Electrical ..................42 (1) Charge .................. 3 Operation Modes .................
Page 63 1-UP/2-UP Control ................66 Fuser Control .................. 67 Fuser Control Method ............... 67 Warm-up Control ..............67 Mode Control: READY, LIGHT SLEEP, DEEP SLEEP .... 68 Printing Mode Control ............... 68 Not Ready State Detection During Printing ......68 Oil Roll Control ................. 69 Fuser Fan Control ..............
Page 64: Print Process
EPSON ColorPage EPL-C8200 Revision A 2.1 Print Process 2.1.1 Print Process Overview This is a full-color laser printer using the Xerographic process. This Transfer process forms an image of toner (Yellow, Magenta, Cyan and Black) on the surface of the drum. The image of one color is then transferred onto the IBT Belt Assembly (Belt).
Page 65: Print Process - Major Components
EPSON ColorPage EPL-C8200 Revision A 2.1.2 Print Process - Major Components The major components of the printer are shown in the figure below. NOTE: In this document Developer Assembly Y, Developer Assembly M, Developer Assembly C, and Developer Assembly Bk are termed Developer Assembly.
Page 66: Print Process Description
EPSON ColorPage EPL-C8200 Revision A 2.1.3 Print Process Description The BCR is always in contact with the surface of the drum, driven by the drum rotation. The BCR is a conductive roll, receiving discharge voltage from the HVPS. The discharge voltage is negative DC voltage to which AC 2.1.3.1 (1) Charge...
Page 67: Exposure
EPSON ColorPage EPL-C8200 Revision A 2.1.3.2 (2) Exposure The laser beam irradiated on the drum surface generates electron- hole pairs in the photoconductive layer. (Excited electrons create a In the exposure step, the system scans the drum surface (negatively hole in the conductive band.) The electrons are attracted by the...
Page 68: Development
EPSON ColorPage EPL-C8200 Revision A 2.1.3.3 (3) Development In the development step, toner particles are attracted to the invisible electrostatic latent image on the drum surface to form a visible toner image. This printer employs the rotary and trickle development methods. In rotary development, four Developer Assemblies rotate in sequence;...
Page 69 EPSON ColorPage EPL-C8200 Revision A As the printer prints more pages, the toner in the developer decreases. To maintain proper developer density, it is necessary to resupply toner to the Developer Assembly from the Toner Cartridge. This is called ‘Toner Dispensing.’ The Toner Dispensing mechanism uses two types of controls (PCDC and ADC).
Page 70 EPSON ColorPage EPL-C8200 Revision A The carrier looses its electrical charges. This occurs because the surface of a carrier particle may be covered with a toner particle or may be damaged by agitation. To maintain the electrical charge of carrier particles, a small amount of carrier is mixed in the toner;...
Page 71: First Transfer (Drum Belt)
EPSON ColorPage EPL-C8200 Revision A 2.1.3.4 (4) First Transfer (Drum Belt) In the first transfer step, the toner image formed on the drum surface is transferred onto the belt (Transfer Assembly) by the 1st BTR (First Bias Transfer Roll). The 1st BTR is a conductive roll, receiving positive high voltage from the HVPS.
Page 72: Cleaning (Drum)
EPSON ColorPage EPL-C8200 Revision A 2.1.3.5 (5) Cleaning (Drum) Electrical drum cleaning An electrical charge still remains on the drum surface after the In the Cleaning (Drum) step, the residual toner on the drum surface is residual toner has been scraped off. This residual electrical charge scraped off and the residual charge is cleaned off.
Page 73: Repeat (Forming A Complete Full-Color Toner Image)
EPSON ColorPage EPL-C8200 Revision A 2.1.3.6 (6) Repeat (Forming a complete full-color toner image) In the Repeat step (forming a complete full-color toner image), the toner image of each color on the drum surface is transferred onto the belt and is repeated four times, resulting in a complete full-color toner image on the belt.
Page 74: Second Transfer (Belt Paper)
EPSON ColorPage EPL-C8200 Revision A 2.1.3.7 (7) Second Transfer (Belt Paper) In the Second Transfer step, the complete image on the belt is transferred onto the paper. This is done by supplying voltage to the Contact Roll, Back Up Roll and 2nd BTR (Second Bias Transfer Roll).
Page 75 EPSON ColorPage EPL-C8200 Revision A In the Repeat step (forming a complete full-color toner image), the toner image is transferred onto the belt from the drum surface four times. If, during these transfers, the 2nd BTR is touching the belt, the toner image created up to this point will be destroyed.
Page 76: Detach
EPSON ColorPage EPL-C8200 Revision A 2.1.3.8 (8) Detach 2.1.3.9 (9) Cleaning (Belt) In the detach step, the charge on the paper is neutralized/removed. This In the Cleaning (Belt) step, the belt is cleaned after the image has been is done when the Detach Saw gives negative DC voltage to the back transferred onto the paper.
Page 77: Fusing
EPSON ColorPage EPL-C8200 Revision A 2.1.3.10 (10) Fusing In the Fusing step, the toner (image) is fused onto the paper by heat and pressure. The complete full-color toner image transferred onto the paper form the belt is very fragile, so it must be fused onto the paper by the Fuser Assembly.
Page 78: Print Data Flow
EPSON ColorPage EPL-C8200 Revision A 2.2 Print Data Flow NOTE: How a two-dimensional image is formed Scanning the laser beam over the drum’s surface from one side to the other by switching the laser beam ON and OFF produces 2.2.1 Data Flow a dot image of one line.
Page 79: Driver Power Transmission Path
EPSON ColorPage EPL-C8200 Revision A 2.3 Driver Power Transmission Path 2.3.1 Process Motor Assembly The rotational force of the Process Motor Assembly is transmitted to the Process WDD Assembly and then transmitted to various units as shown below. Figure 2-19. Drive Transmission in Process Motor Assembly...
Page 80: P/H Motor Assembly
EPSON ColorPage EPL-C8200 Revision A 2.3.2 P/H Motor Assembly The rotational force of the P/H Motor Assembly is transmitted to the Fuser Drive Assembly and P/H Drive Assembly and then to various units as shown on the right. Figure 2-20. Drive Transmission in P/H Motor assembly...
Page 81: Dispense Motor Assembly
EPSON ColorPage EPL-C8200 Revision A 2.3.3 Dispense Motor Assembly 2.3.4 Rotary Motor Assembly The Dispense Motor Assembly drives the Auger in the Developer The Rotary Motor Assembly drives the Rotary Frame Assembly. Assembly. (The Auger supplies the toner from the Toner Cartridge to the Developer Assembly.)
Page 82: Gear Layout
EPSON ColorPage EPL-C8200 Revision A 2.3.5 Gear Layout Figure 2-23. Gear Layout Chapter 2 Operating Principles 2-19...
Page 83: Paper Transportation
EPSON ColorPage EPL-C8200 Revision A 2.4 Paper Transportation 2.4.1 Paper Transportation Path (No Option) NOTE: In this document, Cassettes 1 - 4 are defined as follows: Cassette 1 (LC1): Standard universal cassette Cassette 2 (LC2): Top tray (Large Capacity Paper Unit / 500-Sheet...
Page 84: Main Components
EPSON ColorPage EPL-C8200 Revision A 2.5 Main Components This section describes the main components and their functions. Each subsection has a figure illustrating the component and its function. The major components are listed below. Paper Tray Paper Feeder Multi Sheet Inserter...
Page 85: Paper Tray
EPSON ColorPage EPL-C8200 Revision A 2.5.1 Paper Tray 1. Universal Tray The End Guide can be moved toward the paper feed and holds the paper stack in place. By moving the End Guide, the moving force is transmitted to the Sector Gear and the position of the Tray Size Actuator changes.
Page 86: Paper Feeder
EPSON ColorPage EPL-C8200 Revision A 2.5.2 Paper Feeder 1. Size Switch Assembly The Size Switch Assembly consists of four Paper Size Switches. (The switches are directly mounted on the circuit board.) When the Tray Size Actuator position changes, the ON/OFF combinations of these switches change and the printer detects the paper size and the paper tray.
Page 87: Multi Sheet Inserter (Msi)
EPSON ColorPage EPL-C8200 Revision A 2.5.3 Multi Sheet Inserter (MSI) (d) MSI Short N/P Sensor When the MSI N/P Actuator position changes, the MSI Short N/ 1. MSI Assembly P Sensor detects paper on the MSI Assembly. The MSI Short N/ The MSI Assembly feeds paper from the MSI Tray.
Page 88 EPSON ColorPage EPL-C8200 Revision A 2. MSI Tray Assembly The MSI Tray Assembly hold the paper stack on the MSI Assembly. RETARD PAD ASSY Figure 2-28. Multi Sheet Inserter Chapter 2 Operating Principles 2-25...
Page 89: Paper Transportation
(b) Pre-Registration Roll Assembly transfers paper from the paper in Section 10.) tray or the MSI Assembly onto the Registration Metal Roll and *The printer can use EPSON Color Laser Transparencies Registration Rubber Roll. Until the top of the paper reaches the (S041175, S041174) only.
Page 90 EPSON ColorPage EPL-C8200 Revision A Figure 2-29. Paper Transportation Chapter 2 Operating Principles 2-27...
Page 91: Xerographics I
EPSON ColorPage EPL-C8200 Revision A 2.5.5 Xerographics I (d) To form a proper electrostatic latent image on the drum surface, the laser scanning timing and the writing timing of the image 1. ROS Assembly data must be coordinated. The SOS Sensor on the SOS PWB...
Page 92 EPSON ColorPage EPL-C8200 Revision A 2.5.6 Xerographics II 5. ADC Sensor Assembly The ADC Sensor Assembly consists of the ADC Sensor, ADC 1. Drum Cartridge Solenoid and others. The Drum Cartridge consists of the Xero. Cartridge, Waste Toner Box and others.
Page 93 EPSON ColorPage EPL-C8200 Revision A Figure 2-31. Xerographics II Chapter 2 Operating Principles 2-30...
Page 94: Development
EPSON ColorPage EPL-C8200 Revision A 2.5.7 Development (a) The three Augers in the Developer Assembly: • Supplies toner from the Toner Cartridge to the Developer 1. Used Cartridge Sensor Assembly. The Used Cartridge Sensor detects whether the toner cartridge is •...
Page 95 EPSON ColorPage EPL-C8200 Revision A Figure 2-32. Development Chapter 2 Operating Principles 2-32...
Page 96: Ibt-I
EPSON ColorPage EPL-C8200 Revision A 2.5.8 IBT-I Process Motor runs, the transfer reference marks are alternately detected. This prevents the image from being transferred onto 1. Transfer Assembly the same location on the belt all the time—something that leads The Transfer Assembly consists of the following components: to image degradation.
Page 97: Ibt-Ii
EPSON ColorPage EPL-C8200 Revision A 2.5.9 IBT-II (a) The Cleaning Blade moves forward to the IBT Belt Assembly after the 2nd transfer process and scrapes off the remaining 1. 2nd BTR Assembly toner on the belt. The 2nd BTR Assembly consists of the following components: (b) The Auger transfers the scraped toner to the Auger High Assembly.
Page 98: Fusing-I
EPSON ColorPage EPL-C8200 Revision A 2.5.10 Fusing-I Assembly fails, the contact point in the Thermostat opens, shutting off the power supply to the H/R Heater and P/R Heater (secondary overheating prevention mechanism). 1. Fuser Assembly The Fuser Assembly fuses the toner on the paper with heat and •...
Page 99 EPSON ColorPage EPL-C8200 Revision A Figure 2-35. Fusing-I Chapter 2 Operating Principles 2-36...
Page 100: Fusing-Ii
EPSON ColorPage EPL-C8200 Revision A 2.5.11 Fusing-II appear on the paper. The Oil Roll needs to touch the Heat Roll only during the fusing operation; at other times, the Oil Roll must remain separated from the Heat Roll. 1. Fuser Assembly...
Page 101 EPSON ColorPage EPL-C8200 Revision A Figure 2-36. Fusing-II Chapter 2 Operating Principles 2-38...
Page 102: Paper Exit
EPSON ColorPage EPL-C8200 Revision A 2.5.12 Paper Exit 1. Exit-2 Roll Assembly The Exit-2 Roll Assembly transfers the fused paper to the Top Cover Assembly (face down paper ejection). 2. Exit-3 Roll Assembly The Exit-3 Roll Assembly transfers the fused paper to the Top Cover Assembly (face down paper ejection).
Page 103: Drives
EPSON ColorPage EPL-C8200 Revision A 2.5.13 Drives 3. P/H Drive Assembly The P/H Drive Assembly transfers the driving force from the P/H 1. Process Drive Assembly Motor Assembly to the Main P/H Assembly and the Drum Cartridge. The Process Drive Assembly consists of the Process Motor Assembly and Process WDD Assembly.
Page 104 EPSON ColorPage EPL-C8200 Revision A Figure 2-38. Drives Chapter 2 Operating Principles 2-41...
Page 105: Electrical
EPSON ColorPage EPL-C8200 Revision A 2.5.14 Electrical Magnet Roll (Developer Assembly) 1st BTR/Contact Roll (Transfer Assembly) 1. Front Cover Switch R The Front Cover Switch R (interlock switch) detects whether the Detach Saw (2nd BTR Assembly) Front Cover Assembly is opened or closed. If open, the interlock switch shuts off the 24 VDC-I/L and 5 VDC-LD circuits to cut off the 7.
Page 106 EPSON ColorPage EPL-C8200 Revision A Figure 2-39. Electrical Chapter 2 Operating Principles 2-43...
Page 107: Operation Modes
EPSON ColorPage EPL-C8200 Revision A 2.6 Operation Modes The printer has the following 7 operation modes: WARM-UP: The printer is warming up to be print ready. READY: After warm-up, the printer is waiting to print. PRINTING: The printer is printing.
Page 108: Controls
EPSON ColorPage EPL-C8200 Revision A 2.7 Controls 2.7.1 Paper Size Control The following table shows the Paper Size Switch status (ON/OFF), Diagnostic Data (Analog Input Test data), and voltage for the Size Switches for the corresponding paper sizes. NOTE: The Paper Size Switches are SW1, SW2, SW3, and SW4 (viewed from the left when facing the printer);...
Page 109: Paper Tray Selection Control
EPSON ColorPage EPL-C8200 Revision A 2.7.2 Paper Tray Selection Control If the paper tray is not controlled by the Printer Controller, the tray will be selected at the Power ON defined in the table below. Table 2-2. Paper Tray Selection Control...
Page 110: Ohp Side Detection Control
Control function prevents an OHP film from being rolled up with the Heat Roll. The printer detects the side of the OHP from the signals sent by the Front OHP Sensor and the Rear OHP Sensor. Epson exclusive OHP transparency film (S041175/4) has a white edge with a notch on it.
Page 111: Ros Control
EPSON ColorPage EPL-C8200 Revision A 2.7.4 ROS Control 2.7.4.2 Light Quantity Control Image data is input to the ROS (LD Assembly) as electrical signals. 2.7.4.1 Scanner Motor Rotation (The data is represented by the high/low voltage of the electrical signals). The LD Assembly converts the electrical signals into light The following table defines the Scanner Motor Rotation ON/OFF control signals.
Page 112: Process Control
EPSON ColorPage EPL-C8200 Revision A 2.7.5 Process Control For a stable printing process, it is necessary to adjust the image parameters. This parameter adjustment is called Process Control. There are three types of process controls: Electric potential control Toner density control (PCDC) Toner density control (ADC) 2.7.5.1 Electric Potential Control...
Page 113: Toner Density Control (Pcdc)
EPSON ColorPage EPL-C8200 Revision A 2.7.5.2 Toner Density Control (PCDC) Controller PWB The toner density in the developer becomes degraded as more printings are done. To obtain a stable printed image, stable toner density in the developer must be maintained. The PCDC (Pixel Count...
Page 114: Toner Density Control (Adc)
EPSON ColorPage EPL-C8200 Revision A 2.7.5.3 Toner Density Control (ADC) When detecting low toner, the system rotates the Dispense Motor (Dispense Motor Assembly) (driving the Auger in the Developer To obtain stable print quality, it is necessary to maintain constant toner Assembly) for the calculated duration (dispense time) to supply toner to density in the developer.
Page 115: Adc Solenoid Operation
EPSON ColorPage EPL-C8200 Revision A 2.7.5.4 ADC Solenoid Operation 2.7.5.5 Process Sequence The ADC Solenoid turns on/off (ON: 0.5 sec/OFF: 0.5 sec) twice The process sequences are as follows: (nominal) every 300 counts (nominal). This operation causes the Table 2-4. Process Sequence Cleaning Lever to clean the ADC Sensor emitter/receptor.
Page 116: Xerographic Control
EPSON ColorPage EPL-C8200 Revision A 2.7.6 Xerographic Control Table 2-5. BCR/Erase Lamp Control 2.7.6.1 BCR/Erase Lamp Control Status Control item Description Warm-up Turns BCR ON as the Warm-up mode starts at BCR/Erase lamp control in the BCR and the Erase Lamp Control is mode starting power on.
Page 117: Drum Cartridge Replacement
EPSON ColorPage EPL-C8200 Revision A 2.7.6.2 Drum Cartridge Replacement Whenever removing the Drum Cartridge, the printer must be turned off. When the Drum Cartridge is replaced with a new and the printer is on, the printer generates the following image on the furface of the PPC drum so that the Cleaning Blade does not rotate in the reverse direction.
Page 118: Drum Cartridge End Of Life Detection
EPSON ColorPage EPL-C8200 Revision A 2.7.6.3 Drum Cartridge End of Life Detection 2.7.6.4 Waste Toner Box Full Detection 1. End of life detection When the Waste toner box is almost full, the waste toner sensor detects The life of the Drum Cartridge is determined by the number of Drum the status (Signal: High) and the message “Waste T Box Nearfull”...
Page 119: Developer Control
EPSON ColorPage EPL-C8200 Revision A 2.7.7 Developer Control 2.7.7.1 Home Position Detection The Home Position is the starting point for Development Control. The following position is the Home Position of the Rotary Frame Assembly. Home Position: 30 in the opposite direction of the rotation direction from the Bk development position on the Developer Assembly.
Page 120: Toner Cartridge Detection Position
EPSON ColorPage EPL-C8200 Revision A 2.7.7.2 Toner Cartridge Detection Position 2.7.7.4 Development Position The Toner Cartridges are detected by the Cartridge Sensor. The The Developer Assemblies are moved to their development positions by Cartridge Sensor detects the Toner Cartridges at the appropriate the Rotary Frame Assembly rotation.
Page 121: Development Control: Detection Methods
EPSON ColorPage EPL-C8200 Revision A 2.7.7.5 Development Control: Detection Methods (a) No Toner Detection flow 1. Toner Cartridge detection The Cartridge Sensor detects the Toner Cartridges at the detection positions. A photo sensor, it detects reflected light from a Toner...
Page 122 EPSON ColorPage EPL-C8200 Revision A (c) Toner End of Life Warning Reset flow Chapter 2 Operating Principles 2-59...
Page 123: Ibt Control
EPSON ColorPage EPL-C8200 Revision A 2.7.8 IBT Control 2.7.8.1 First Transfer (Drum Belt) Transferring the toner image on the drum onto the belt is called the First Transfer. The First Transfer is done when the HVPS outputs power to the 1st BTR.
Page 124: Second Transfer (Belt Paper)
EPSON ColorPage EPL-C8200 Revision A 2.7.8.2 Second Transfer (Belt Paper) Transferring the toner image on the belt onto the paper is called 2nd Transfer. 2nd transfer is done when the HVPS outputs the power to the Contact Roll. 1. 2nd Transfer Current The resistance of the 2nd BTR and Back Up Roll changes due to time and environment.
Page 125 EPSON ColorPage EPL-C8200 Revision A NOTE:If there is not sufficient time from when the BTR Cam 2. 2nd BTR Advance/Retract control Solenoid is turned on from its off state—because there is not In a 2nd transfer, the 2nd BTR must be in the Advance position.
Page 126 EPSON ColorPage EPL-C8200 Revision A NOTE:The count described above is based on the following: 1 count: - Printing a sheet that has a length (feed direction) of 219mm (LETTER/LEF) or smaller 2 counts: - Printing a sheet that is larger than the above.
Page 127: Discharging
EPSON ColorPage EPL-C8200 Revision A 2.7.8.3 Discharging Toner (excess toner) may be on the belt surface: Residual toner from the 2nd transfer. Discharging is to neutralize/remove the charge on paper after 2nd transfer. It is done by applying high voltage from the HVPS to the Residual toner from the Cin50% patch and BIAS development Detach Saw in the “2nd BTR Assembly.
Page 128 EPSON ColorPage EPL-C8200 Revision A 2. Cleaner solenoid ON/OFF timing (b) Irregular cleaning Table 2-14. Irregular Cleaning On/Off Timing NOTE:The top edge of the image in the 2UP mode is defined as the top edge of the first page on the IBT 1 surface.
Page 129: 1-Up/2-Up Control
EPSON ColorPage EPL-C8200 Revision A 2.7.9 1-UP/2-UP Control 2. 2-UP mode Two sheets are transported the distance equivalent to one belt This section describes the print sequence for 1-UP and 2-UP modes. circumference. The image (toner image) is formed as follows:...
Page 130: Fuser Control
EPSON ColorPage EPL-C8200 Revision A 2.7.10 Fuser Control 2.7.10.2 Warm-up Control When Fuser Warm-up (Warm-up mode) starts, the H/R Heater and P/R 2.7.10.1 Fuser Control Method Heater are turned on. When the Fuser temperature reaches the Fuser control temperature, Fuser Warm-up ends. The Fuser control...
Page 131: Mode Control: Ready, Light Sleep, Deep Sleep
EPSON ColorPage EPL-C8200 Revision A 2.7.10.3 Mode Control: READY, LIGHT SLEEP, DEEP SLEEP 2.7.10.4 Printing Mode Control The ON/OFF controls for the H/R Heater and P/R Heater are defined as The Fuser control temperature for the Printing mode has been follows: determined by the paper type (regular paper, OHP, etc.), color mode...
Page 132: Oil Roll Control
EPSON ColorPage EPL-C8200 Revision A 2.7.10.6 Oil Roll Control 3. Not Ready state: Canceling When the system is determining whether to cancel a Not Ready If the Oil Roll in the Oil Roll Assembly continuously touches the Heat state, it cancels the state after running the P/H Motor Assembly for a Roll, the Fuser Oil may degrade and oil stains may appear on the paper.
Page 133 EPSON ColorPage EPL-C8200 Revision A 1. Oil Roll: Advance/Retract control 2. Emergencies The Oil Roll advanced period is determined by the print count and (a) Emergency stop the waiting time (between print jobs) in the Ready mode. (The Oil If the printer stops (shuts down) because of an emergency such Roll advanced period is from when the Oil Roll starts advancing to as a paper jam, the printer turns off the Oil Cam Solenoid.
Page 134: Fuser Fan Control
EPSON ColorPage EPL-C8200 Revision A 2.7.10.7 Fuser Fan Control 2.7.10.8 Detection Controls in Fuser 1. Oil Roll Assembly end of life detection The Fuser Fan is controlled (ON/OFF or High/Low rotations) by the The life of the Oil Roll Assembly is determined by the number of operation modes as follows: printings (oil quantity being used).
Page 135 EPSON ColorPage EPL-C8200 Revision A (b) Oil Rate Counter 2. New/Old Oil Roll Assembly detection The Oil Rate Counter accumulates the amount of oil being used. The CRU Switch Assembly detects a new/old Oil Roll Assembly. The oil rate is calculated from the following: Metal foil has been attached to the Oil Roll Assembly.
Page 136 EPSON ColorPage EPL-C8200 Revision A 3. Oil Roll Assembly detection 4. Main Fuser Assembly end of life detection The CRU Switch Assembly detects the Oil Roll Assembly. Metal foil (a) End of life detection has been attached to the Oil Roll Assembly. The CRU Switch The life of the Main Fuser Assembly is determined by the print Assembly checks the conductivity of the foil.
Page 137 EPSON ColorPage EPL-C8200 Revision A (d) Processes after replacement Do the following operations after you replace the Main Fuser Assembly with a new one. Doing any of these operations before replacing the Main Fuser Assembly may result in damage to the system or cause the system to malfunction.
Page 138: Controller Operating Principles
EPSON ColorPage EPL-C8200 Revision A 2.8 Controller Operating Principles This section describes the C287MAIN board, the MAIN CONTROLLER The printer uses a data bus 64-bit RISC CPU “R5000-200MHz” for the PWB of the EPL-C8200. processor. A168-pin SDRAM module (CLK:66.7MHz), which is...
Page 139 EPSON ColorPage EPL-C8200 Revision A Table 2-25. C287MAIN Board Major Components (1/3) Refer to: Components Location Function RISC-CPU A RISC*-type CPU, which operates at 200 R5000-200 MHz (internal) and 3.3V. (External: 66.7 MHz) *RISC: Reduced Instruction Set Computer E05B51 (ASIC) •...
Page 140 EPSON ColorPage EPL-C8200 Revision A Table 2-26. C287MAIN Board Major Components (2/3) Table 2-27. C287MAIN Board Major Components (3/3) Refer to: Refer to: Components Location Function Components Location Function AD9561 IC26 8-bit PWM controller (directly connected to W24257AJ-15 IC502/ S-RAM (256k-bit). A high speed working...
Page 141 DISASSEMBLY AND ASSEMBLY/ADJUSTMENT...
Page 142 Table of Contents Overview....................1 Multi Sheet Inserter................. 26 MSI TRAY ASSEMBLY Removal (PL4.1.10) ......26 Precautions for disassembly, assembly and adjustment ....1 MSI ASSEMBLY Removal (PL4.1.1) ........27 Tools ....................2 MSI FRONT COVER Removal (PL4.1.3) ......... 28 Items to check after assembly ............
Page 143 TONER BOX SENSOR Removal (PL6.1.43) ......55 EXIT-1 ROLL ASSEMBLY Removal (PL9.3.7) ......93 ERASE LAMP ASSEMBLY Removal (PL6.1.30) ..... 56 CRU SWITCH ASSEMBLY Removal (PL9.3.25) ..... 94 Development ................... 57 Paper Exit ..................95 Toner Cartridge Removal (PL7.1.1 ~ PL7.1.4) ......57 EXIT TRAY ASSEMBLY Removal (PL10.1.10) ......
Page 144: Overview
EPSON ColorPage EPL-C8200 Revision A 3.1 Overview When servicing, avoid handling any parts forcibly. Doing so might damage the parts and cause printer malfunction. This chapter describes procedures for disassembly, assembly, and Various types of screws are used to assemble the adjustment of the EPL-C8200.
Page 145: Tools
EPSON ColorPage EPL-C8200 Revision A 3.1.2 Tools 3.1.3 Items to check after assembly Table below shows the tools used for servicing. Performs the items described below when completing assembly after repairing the printer or replace any parts. Table 3-1. Tools Clean the housings and the interior of the engine.
Page 146: Disassembly/Assembly Procedures
EPSON ColorPage EPL-C8200 Revision A 3.2 Disassembly/Assembly Procedures Refer to the followings which explain descriptions used in this chapter. Regarding “(PL X, Y, Z)” at the end of each heading of removal This section describes procedures for disassembling/assembling the sections, it corresponds to the numbers in the part list in printer.
Page 147: Exterior View And Part Names
EPSON ColorPage EPL-C8200 Revision A 3.2.1 Exterior View and Part Names The part names used in this manual are based on the after service part names. (They differ from the ones used in Users Guide.) The names of the parts which are frequently handled by the users are shown below.
Page 148: Removing/Replacing The Consumables
EPSON ColorPage EPL-C8200 Revision A 3.2.3 Updating the Program ROM The program ROM of this printer is a flash ROM module and can be updated in one of the following 2 ways: 1. Transferring the ROM updating program data (*.RCC) from the host computer via the standard parallel interface.
Page 149: Updating The Rom Using A Standard Parallel Interface
EPSON ColorPage EPL-C8200 Revision A 3.2.3.1 Updating the ROM using a standard parallel interface 5. To transfer the program data file from the computer to the printer, type the command (shown below) on the DOS prompt (from the Follow the instruction below to update the program ROM using a directory that has “*.RCC”) and press Enter key.
Page 150: Updating By Copying From The Flash Rom Module
EPSON ColorPage EPL-C8200 Revision A 3.2.3.2 Updating by copying from the FLASH ROM module 5. When the program has been properly updated, the printer enters the Ready status. If an error occurs, one of the following messages Follow the steps below.
Page 151: Formatting The Flash Rom Module
EPSON ColorPage EPL-C8200 Revision A 3.2.3.3 Formatting the FLASH ROM Module 4. When an error has occurred, the message bellow appears. # Flash ROM module can be formatted as instructed below. 1. Install the ROM module to be formatted to the socket A of the CONTROLLER PWB.
Page 152: Cover
EPSON ColorPage EPL-C8200 Revision A 3.2.4 Cover 3.2.4.2 FRONT LOWER COVER Removal (PL1.1.5) 1. Remove the UNIVERSAL TRAY. 3.2.4.1 FRONT COVER ASSEMBLY Removal (PL1.1.1) 2. Remove 2 screws (silver, cup head, 8mm) securing the FRONT 1. Take out the UNIVERSAL TRAY about 20cm. (See Section 3.2.5.1.) LOWER COVER, and remove the FRONT LOWER COVER.
Page 153: Top Cover Assembly Removal (Pl1.1.20)
EPSON ColorPage EPL-C8200 Revision A 3.2.4.3 TOP COVER ASSEMBLY Removal (PL1.1.20) 1. Open the FRONT COVER ASSEMBLY. 2. Open the EXIT UPPER ASSEMBLY. NOTE: In the following step, the TOP COVER ASSEMBLY is kept connected to the printer body with a harness. Therefore, do not move the TOP COVER ASSEMBLY too away from the printer.
Page 154: Inner Cover Assembly Removal (Pl1.1.10)
EPSON ColorPage EPL-C8200 Revision A 3.2.4.4 INNER COVER ASSEMBLY Removal (PL1.1.10) NOTE: Be sure to perform Step 1 to support the FRONT COVER ASSEMBLY. 1. Take out the UNIVERSAL TRAY about 20cm. 2. Open the FRONT COVER ASSEMBLY. 3. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 4.
Page 155: Rear Cover Assembly Removal (Pl1.1.30)
EPSON ColorPage EPL-C8200 Revision A 3.2.4.5 REAR COVER ASSEMBLY Removal (PL1.1.30) 1. Take out the MAIN P/H ASSEMBLY. (See Section 3.2.8.1.) 2. Pressing the tub at the upper edge of the O/H COVER, pull the O/H COVER down to release the hook attaching the cover to the REAR COVER ASSEMBLY.
Page 156: Filter Assembly Removal (Pl1.1.32)
EPSON ColorPage EPL-C8200 Revision A 3.2.4.6 FILTER ASSEMBLY Removal (PL1.1.32) 3.2.4.7 LEFT LOWER COVER Removal (PL1.1.40) 1. Hold the tab of the FILTER ASSEMBLY at the back and unlock it 1. Take the UNIVERSAL TRAY out. from the REAR COVER.
Page 157: Right Cover Assembly Removal (Pl1.1.50)
EPSON ColorPage EPL-C8200 Revision A 3.2.4.8 RIGHT COVER ASSEMBLY Removal (PL1.1.50) 3.2.4.9 OPERATION PANEL Removal (PL1.1.60) 1. Open the FRONT COVER ASSEMBLY. 1. Remove the TOP COVER along with the OPERATION PANEL. (See Section 3.2.4.3.) 2. Take the MAIN P/H ASSEMBLY out.
Page 158: Paper Tray
EPSON ColorPage EPL-C8200 Revision A 3.2.5 Paper Tray 3.2.5.2 FRONT SNUBBER Removal (PL2.2.9) 1. Take the UNIVERSAL TRAY out. (See Section 3.2.5.1.) 3.2.5.1 UNIVERSAL TRAY Removal (PL2.1.1) NOTE: In the following steps, be careful not to bend the edge of the NOTE: In the following step, be careful not to drop the UNIVERSAL FRONT SNUBBER where paper is placed.
Page 159: End Guide (Pl2.2.16), Sector Gear (Pl2.2.17) Removal
EPSON ColorPage EPL-C8200 Revision A 3.2.5.3 END GUIDE (PL2.2.16), SECTOR GEAR (PL2.2.17) Removal 1. Take the UNIVERSAL TRAY out. (See Section 3.2.5.1.) 2. Move the END GUIDE to the right end. (= minimum paper size fits) NOTE: After removing the FRONT GUIDE ASSEMBLY, hold the BOTTOM PLATE ASSEMBLY down.
Page 160 EPSON ColorPage EPL-C8200 Revision A 8. Remove 2 screws (black, cup head, 8mm) securing the LOCK PLATE by the right edge. 9. Remove 2 screws (black, cup head, 8mm) securing the LOCK PLATE by the left edge, and remove the LOCK PLATE.
Page 161: Paper Feeder
EPSON ColorPage EPL-C8200 Revision A 3.2.6 Paper Feeder 3.2.6.1 TURN IN CHUTE Removal (PL3.1.18) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MAIN P/H ASSEMBLY with the MSI TRAY installed on NOTE: In the next step, be careful not to damage the hinge part of the TURN IN CHUTE.
Page 162: Turn Roll Assembly Removal (Pl3.1.11)
EPSON ColorPage EPL-C8200 Revision A 3.2.6.2 TURN ROLL ASSEMBLY Removal (PL3.1.11) NOTE: In the next step, the pulley and the gear in the TURN ROLL ASSEMBLY will dislocate. Therefore, be careful not to drop 1. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) and lose them.
Page 163: Feed Roll Removal (Pl3.1.3)
EPSON ColorPage EPL-C8200 Revision A 3.2.6.3 FEED ROLL Removal (PL3.1.3) 1. Remove the UNIVERSAL TRAY. (See Section 3.2.5.1.) 2. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 3. Remove the MAIN P/H ASSEMBLY with the MSI TRAY ASSEMBLY installed on it. (See Section 3.2.8.1.) NOTE: In the following step, be careful with the metal plate as you maybe hurt with its sharp edge.
Page 164: Feed Solenoid Removal (Pl3.1.9)
EPSON ColorPage EPL-C8200 Revision A 3.2.6.4 FEED SOLENOID Removal (PL3.1.9) 1. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) NOTE: In the following step, the OPTION BRACKET is kept connected to the printer body with a harness. Therefore, do not move the OPTION BRACKET too away from the printer.
Page 165: Feed Roll Assembly Removal (Pl3.1.1)
EPSON ColorPage EPL-C8200 Revision A 3.2.6.5 FEED ROLL ASSEMBLY Removal (PL3.1.1) 1. Remove the REAR COVER ASSEMBLY. 2. Remove the UNIVERSAL TRAY. (See Section 3.2.5.1.) 3. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 4. Remove the MAIN P/H ASSEMBLY with the MSI TRAY ASSEMBLY installed on it.
Page 166: Size Switch Assembly Removal (Pl3.1.9)
EPSON ColorPage EPL-C8200 Revision A 3.2.6.6 SIZE SWITCH ASSEMBLY Removal (PL3.1.9) 1. Draw the UNIVERSAL TRAY out. 2. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 3. Remove the LVPS. (See Section 3.2.16.1.) NOTE: In the following step, the OPTION BRACKET is kept connected to the printer body with a harness.
Page 167: Tray N/P Sensor Assembly Removal (Pl3.1.30)
EPSON ColorPage EPL-C8200 Revision A 3.2.6.7 TRAY N/P SENSOR ASSEMBLY Removal (PL3.1.30) 1. Remove the UNIVERSAL TRAY. (See Section 3.2.5.1.) 2. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 3. Remove the MAIN P/H ASSEMBLY with the MSI TRAY ASSEMBLY installed on it.
Page 168: Low Paper Sensor Removal (Pl3.1.35)
EPSON ColorPage EPL-C8200 Revision A 3.2.6.8 LOW PAPER SENSOR Removal (PL3.1.35) 3.2.6.9 TRAY NO PAPER SENSOR Removal (PL3.1.32) 1. Remove the UNIVERSAL TRAY. (See Section 3.2.5.1.) 1. Remove the UNIVERSAL TRAY. (See Section 3.2.5.1.) 2. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2.
Page 169: Multi Sheet Inserter
EPSON ColorPage EPL-C8200 Revision A 3.2.7 Multi Sheet Inserter 3.2.7.1 MSI TRAY ASSEMBLY Removal (PL4.1.10) 1. Using a Phillips screw driver, push the lock in the front arm of the MSI TRAY ASSEMBLY to the rear, and release the front arm of the MSI FRAME.
Page 170: Msi Assembly Removal (Pl4.1.1)
EPSON ColorPage EPL-C8200 Revision A 3.2.7.2 MSI ASSEMBLY Removal (PL4.1.1) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Draw the MAIN P/H ASSEMBLY out. 3. Disconnect 2 connectors (P/J92B and 113B) connecting the MSI ASSEMBLY and MSI P/H ASSEMBLY.
Page 171: Msi Front Cover Removal (Pl4.1.3)
EPSON ColorPage EPL-C8200 Revision A 3.2.7.3 MSI FRONT COVER Removal (PL4.1.3) 3.2.7.4 MSI REAR COVER Removal (PL4.1.4) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 2.
Page 172: Msi Top Cover Assembly Removal (Pl4.2.4)
EPSON ColorPage EPL-C8200 Revision A 3.2.7.5 MSI TOP COVER ASSEMBLY Removal (PL4.2.4) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 3. Remove the MSI FRONT COVER. (See Section 3.2.7.4.) 4. Remove the MSI REAR COVER. (See Section 3.2.7.3.) NOTE: In the following step, MSI TOP COVER ASSEMBLY is kept connected with MSI FRAME by a harness.
Page 173: Msi Edge Sensor Removal (Pl4.2.6)
EPSON ColorPage EPL-C8200 Revision A 3.2.7.6 MSI EDGE SENSOR Removal (PL4.2.6) 3.2.7.7 MSI SHORT N/P SENSOR Removal (PL4.2.7) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 2.
Page 174: Pick Up Roll Removal (Pl4.2.11)
EPSON ColorPage EPL-C8200 Revision A 3.2.7.8 PICK UP ROLL Removal (PL4.2.11) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) NOTE: In the following step, be careful not to break the hooks for the FRONT CORE ROLL.
Page 175: Retard Pad Assembly Removal (Pl4.3.3)
EPSON ColorPage EPL-C8200 Revision A 3.2.7.9 RETARD PAD ASSEMBLY Removal (PL4.3.3) After installing the RETARD PAD ASSEMBLY, 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) align the RETARD SPRING with the groove on 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) the MSI FRAME by using tweezers.
Page 176: Pick Up Solenoid Removal (Pl4.2.21)
EPSON ColorPage EPL-C8200 Revision A 3.2.7.10 PICK UP SOLENOID Removal (PL4.2.21) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 3. Remove the MSI REAR COVER. (See Section 3.2.7.4.) 4. Disconnect the connector (P/J201B) for the PICK UP SOLENOID and release the harness from the clamp.
Page 177: Msi Clutch Removal (Pl4.2.26)
EPSON ColorPage EPL-C8200 Revision A 3.2.7.11 MSI CLUTCH Removal (PL4.2.26) 12. Remove the E-ring securing the MSI SHAFT and remove the shaft from the MSI CLUTCH. 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 3.
Page 178: Msi Roll Assembly Removal (Pl4.2.9)
EPSON ColorPage EPL-C8200 Revision A 3.2.7.12 MSI ROLL ASSEMBLY Removal (PL4.2.9) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 3. Remove the MSI FRONT COVER. (See Section 3.2.7.3.) 4. Remove the MSI REAR COVER. (See Section 3.2.7.4.) 5.
Page 179: Msi Bottom Assembly Removal (Pl4.3.9)
EPSON ColorPage EPL-C8200 Revision A 3.2.7.13 MSI BOTTOM ASSEMBLY Removal (PL4.3.9) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 3. Remove the MSI FRONT COVER. (See Section 3.2.7.3.) 4. Remove the MSI REAR COVER. (See Section 3.2.7.4.) 5.
Page 180: Msi Long N/P Sensor Removal (Pl4.3.16)
EPSON ColorPage EPL-C8200 Revision A 3.2.7.14 MSI LONG N/P SENSOR Removal (PL4.3.16) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 3. Remove the MSI FRONT COVER. (See Section 3.2.7.3.) 4. Remove the MSI REAR COVER. (See Section 3.2.7.4.) 5.
Page 181: Paper Transportation
EPSON ColorPage EPL-C8200 Revision A 3.2.8 Paper Transportation 3.2.8.1 MAIN P/H ASSEMBLY Removal (PL5.1.1) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 3. Remove the MAIN P/H COVER from the MAIN P/H ASSEMBLY.
Page 182: Pre-Regi. Chute Assembly Removal (Pl5.1.5)
EPSON ColorPage EPL-C8200 Revision A 3.2.8.2 PRE-REGI. CHUTE ASSEMBLY Removal (PL5.1.5) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 3. Remove the MAIN P/H ASSEMBLY. (See Section 3.2.8.1.) 4. Remove 2 screws (gold, tapped, 8mm) securing the PRE-REGI.
Page 183: P/H Turn Chute Assembly Removal (Pl5.1.4)
EPSON ColorPage EPL-C8200 Revision A 3.2.8.3 P/H TURN CHUTE ASSEMBLY Removal (PL5.1.4) 6. Push the upper pegs in the P/H TURN CHUTE ASSEMBLY inward and remove the P/H TURN CHUTE ASSEMBLY from the P/H 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) FRAME ASSEMBLY 2.
Page 184: Regi. Chute Assembly Removal (Pl5.1.6)
EPSON ColorPage EPL-C8200 Revision A 3.2.8.4 REGI. CHUTE ASSEMBLY Removal (PL5.1.6) 6. Open the REGI. CHUTE ASSEMBLY vertically and shift it to the rear until it touches the bottom of the rear stud to release the hole in 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) the front from the front stud.
Page 185: Pre-Regi. Clutch Removal (Pl5.2.8)
EPSON ColorPage EPL-C8200 Revision A 3.2.8.5 PRE-REGI. CLUTCH Removal (PL5.2.8) 6. Remove 2 E-rings fixing the PRE-REGI. SUPPORT and remove the PRE-REGI. SUPPORT toward the rear. 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 7. Among 2 PRE-REGI. GEAR 1, remove the outer one to the rear 2.
Page 186: Pre-Regi. Roll Assembly Removal (Pl5.2.4)
EPSON ColorPage EPL-C8200 Revision A 3.2.8.6 PRE-REGI. ROLL ASSEMBLY Removal (PL5.2.4) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 3. Remove the MAIN P/H ASSEMBLY. (See Section 3.2.8.1.) 4. Remove the PRE-REGI. CHUTE ASSEMBLY. (See Section 3.2.8.4.)
Page 187: Regi. Clutch Removal (Pl5.2.15)
EPSON ColorPage EPL-C8200 Revision A 3.2.8.7 REGI. CLUTCH Removal (PL5.2.15) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 3. Remove the MAIN P/H ASSEMBLY. (See Section 3.2.8.1.) NOTE: In the following step, hold the REGI. CHUTE ASSEMBLY to keep it closed while turning over the MAIN P/H ASSEMBLY.
Page 188: Regi. Brake Clutch Removal (Pl5.2.20)
EPSON ColorPage EPL-C8200 Revision A 3.2.8.8 REGI. BRAKE CLUTCH Removal (PL5.2.20) 7. Remove the REGI. BRAKE CLUTCH and REGI. BRAKE GEAR from the REGI. BRAKE BRACKET. 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 3.
Page 189: Regi. Metal Roll Removal (Pl5.2.16)
EPSON ColorPage EPL-C8200 Revision A 3.2.8.9 REGI. METAL ROLL Removal (PL5.2.16) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 3. Remove the MAIN P/H ASSEMBLY. (See Section 3.2.8.1.) 4. Remove the REGI. CLUTCH. (See Section 3.2.8.7.) 5.
Page 190: Regi. Rubber Roll Removal (Pl5.2.24)
EPSON ColorPage EPL-C8200 Revision A 3.2.8.10 REGI. RUBBER ROLL Removal (PL5.2.24) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 3. Remove the MAIN P/H ASSEMBLY. (See Section 3.2.8.1.) 4. Remove the REGI. CLUTCH. (See Section 3.2.8.7.) 5.
Page 191: Regi. Sensor Removal (Pl5.2.28)
EPSON ColorPage EPL-C8200 Revision A 3.2.8.11 REGI. SENSOR Removal (PL5.2.28) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 3. Remove the MAIN P/H ASSEMBLY. (See Section 3.2.8.1.) NOTE: In the following step, hold the REGI. CHUTE ASSEMBLY to keep it closed while turning over the MAIN P/H ASSEMBLY.
Page 192: Front Ohp Sensor Removal (Pl5.2.31)
EPSON ColorPage EPL-C8200 Revision A 3.2.8.12 FRONT OHP SENSOR Removal (PL5.2.31) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 3. Remove the MAIN P/H ASSEMBLY. (See Section 3.2.8.1.) NOTE: In the following steps, hold the REGI. CHUTE ASSEMBLY to keep it closed while turning over the MAIN P/H ASSEMBLY.
Page 193: Rear Ohp Sensor Removal (Pl5.2.32)
EPSON ColorPage EPL-C8200 Revision A 3.2.8.13 REAR OHP SENSOR Removal (PL5.2.32) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MSI ASSEMBLY. (See Section 3.2.7.2.) 3. Remove the MAIN P/H ASSEMBLY. (See Section 3.2.8.1.) NOTE: In the following steps, hold the REGI. CHUTE ASSEMBLY to keep it closed while turning over the MAIN P/H ASSEMBLY.
Page 194: Xerographics
EPSON ColorPage EPL-C8200 Revision A 3.2.9 Xerographics 3.2.9.2 WASTE TONER BOX Removal (PL6.1.12) 1. Open the FRONT COVER ASSEMBLY. 3.2.9.1 DRUM CARTRIDGE Removal (PL6.1.10) NOTE: After removing the WASTE TONER BOX in the following 1. Open the FRONT COVER ASSEMBLY.
Page 195: Ros Assembly Removal (Pl6.1.1)
EPSON ColorPage EPL-C8200 Revision A 3.2.9.3 ROS ASSEMBLY Removal (PL6.1.1) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 2. Remove 8 screws (silver, cup head, 6mm) securing the ROS COVER and remove the ROS COVER. 3. Disconnect 3 connectors (P/J121, 122, and 124) for the ROS ASSEMBLY.
Page 196: Adc Sensor Assembly Removal (Pl6.1.20)
EPSON ColorPage EPL-C8200 Revision A 3.2.9.4 ADC SENSOR ASSEMBLY Removal (PL6.1.20) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 2. Remove the DRUM CARTRIDGE. (See Section 3.2.9.1.) 3. Remove the TENSION LEVER. (See Section 3.2.11.1.) 4. Remove the INNER COVER ASSEMBLY. (See Section 3.2.4.4.) 5.
Page 197: Xl Rail Assembly Removal (Pl6.1.40)
EPSON ColorPage EPL-C8200 Revision A 3.2.9.5 XL RAIL ASSEMBLY Removal (PL6.1.40) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 2. Remove the DRUM CARTRIDGE. (See Section 3.2.9.1.) 3. Remove the ROS ASSEMBLY. (See Section 3.2.9.3.) 4. Remove the connectors P/J86 and P/J116 for the ERASE LAMP ASSEMBLY and the TONER BOX HARNESS, respectively.
Page 198: Waste Toner Sensor Removal (Pl6.1.42)
EPSON ColorPage EPL-C8200 Revision A 3.2.9.6 WASTE TONER SENSOR Removal (PL6.1.42) 3.2.9.7 TONER BOX SENSOR Removal (PL6.1.43) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 2. Remove the DRUM CARTRIDGE. (See Section 3.2.9.1.) 2.
Page 199: Erase Lamp Assembly Removal (Pl6.1.30)
EPSON ColorPage EPL-C8200 Revision A 3.2.9.8 ERASE LAMP ASSEMBLY Removal (PL6.1.30) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 2. Remove the DRUM CARTRIDGE. (See Section 3.2.9.1.) 3. Remove the ROS ASSEMBLY. (See Section 3.2.9.3.) 4. Remove the XL RAIL ASSEMBLY. (See Section 3.2.9.5.) 5.
Page 200: Development
EPSON ColorPage EPL-C8200 Revision A 3.2.10 Development NOTE: The generic term “Toner Cartridge” is used for “TONER Cartridge Y”, “TONER CARTRIDGE M”, “TONER CARTRIDGE C”, and “TONER CARTRIDGE K”. 3.2.10.1 Toner Cartridge Removal (PL7.1.1 ~ PL7.1.4) 1. Open the FRONT COVER ASSEMBLY.
Page 201: Developer Assembly Removal (Pl7.1.10, Pl7.1.20, Pl7.1.30, Pl7.1.40)
EPSON ColorPage EPL-C8200 Revision A 3.2.10.2 Developer Assembly Removal (PL7.1.10, PL7.1.20, PL7.1.30, PL7.1.40) NOTE: The generic term “Developer Assembly” is used for “DEVELOPPER ASSEMBLY Y/M/C/K”. 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 2. Remove the DRUM CARTRIDGE. (See Section 3.2.9.1.) 3.
Page 202: Developer Removal (Pl7.1.13, Pl7.1.23, Pl7.1.33, Pl7.1.43)
EPSON ColorPage EPL-C8200 Revision A 3.2.10.3 Developer Removal (PL7.1.13, PL7.1.23, PL7.1.33, PL7.1.43) NOTE: The generic term “Developer” is used for “DEVELOPER Y/M/C/ K”. NOTE: The generic term “Deve. Upper Assembly” is used for “DEVE. UPPER ASSEMBLY Y/M/C/K”. 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 2.
Page 203: Rotary Sensor Removal (Pl7.2.22)
EPSON ColorPage EPL-C8200 Revision A 3.2.10.4 ROTARY SENSOR Removal (PL7.2.22) 1. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 2. Release the harness from the hook on the FAN DUCT. 3. Disconnect the connector (P/J82) for the DEVE. FAN. 4. Remove the screw (black, cup head, 8mm) securing the FAN DUCT, and shift the FAN DUCT upward to release the hooks from the frame.
Page 204: Rotary Frame Assembly Removal (Pl7.2.2)
EPSON ColorPage EPL-C8200 Revision A 3.2.10.5 ROTARY FRAME ASSEMBLY Removal (PL7.2.2) 18. Remove the LVPS. (See Section 3.2.16.1.) 1. Remove the FRONT COVER ASSEMBLY. (See Section 3.2.4.1.) 19. Remove the FUSER DRIVE ASSEMBLY. (See Section 3.2.14.6.) 2. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 20.
Page 205 EPSON ColorPage EPL-C8200 Revision A NOTE: As the ROTARY FRAME ASSEMBLY weighs heavily, note the points below when handling it in the following steps: Avoid dropping the ROTARY FRAME ASSEMBLY. Keep the ROTARY FRAME ASSEMBLY well away from adjacent parts.
Page 206: Cartridge Sensor Removal (Pl7.2.26)
EPSON ColorPage EPL-C8200 Revision A 3.2.10.6 CARTRIDGE SENSOR Removal (PL7.2.26) 9. Remove the screw (gold, tapped, 10mm) securing the CARTRIDGE SENSOR, and remove the CARTRIDGE SENSOR from the CART. 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) SENSOR HOLDER.
Page 207: Used Cart. Sensor Removal (Pl7.2.30)
EPSON ColorPage EPL-C8200 Revision A 3.2.10.7 USED CART. SENSOR Removal (PL7.2.30) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 2. Disconnect the connector P/J87 and P/J197 for the USED CART. SENSOR and the FRONT COVER SWITCH L, respectively, and release the harnesses from the USED SENSOR PLATE.
Page 208: Ibt
EPSON ColorPage EPL-C8200 Revision A 3.2.11 IBT 3.2.11.1 TENSION LEVER Removal (PL8.1.4) 1. Open the FRONT COVER ASSEMBLY. 2. Remove the DRUM CARTRIDGE. (See Section 3.2.9.1.) NOTE: In the following step, keep your hands off the IBT BELT ASSEMBLY. 3. Turn the TENSION LEVER to the locking position and remove the screw (gold, with a washer, 12mm) securing the TENSION LEVER.
Page 209: Transfer Assembly Removal (Pl8.1.3)
EPSON ColorPage EPL-C8200 Revision A 3.2.11.2 TRANSFER ASSEMBLY Removal (PL8.1.3) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 2. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 3. Remove the DRUM CARTRIDGE. (See Section 3.2.9.1.) 4. Remove the TENSION LEVER. (See Section 3.2.11.1.) 5.
Page 210 EPSON ColorPage EPL-C8200 Revision A 18. Shift the SLIDE COLLAR inward and remove the IBT BEARING-4 from the frame. When installing the IBT BELT ASSEMBLY, cover the belt surface with paper to protect it. 19. Lift up the both ends of the IBT DEVE ROLL ASSEMBLY in the...
Page 211: Btr Cam Solenoid Removal (Pl8.1.15)
EPSON ColorPage EPL-C8200 Revision A 3.2.11.3 BTR CAM SOLENOID Removal (PL8.1.15) When installing the BTR CAM SOLENOID, make sure it 1. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) is under the following condition: 2. Remove the HVPS. (See Section 3.2.16.2.) The arm of the BTR CAM SOLENOID is in induced condition.
Page 212: Belt Cleaner Assembly Removal (Pl8.1.30)
EPSON ColorPage EPL-C8200 Revision A 3.2.11.4 BELT CLEANER ASSEMBLY Removal (PL8.1.30) NOTE: In the following step, place the removed BELT CLEANER ASSEMBLY on a sheet of paper as toner may spill. 1. Remove the FRONT COVER ASSEMBLY. (See Section 3.2.4.1.) 4.
Page 213: 2Nd Btr Assembly Removal (Pl8.1.20)
EPSON ColorPage EPL-C8200 Revision A 3.2.11.5 2ND BTR ASSEMBLY Removal (PL8.1.20) 1. Remove the FUSER ASSEMBLY with the EXIT TRAY ASSEMBLY and the OIL ROLL ASSEMBLY installed on it. (See Section 3.2.12.2.) 2. Remove the BELT CLEANER ASSEMBLY. (See Section 3.2.11.4.) NOTE: In the following step, do not touch the IBT BELT ASSEMBLY and the 2ND BTR ASSEMBLY.
Page 214: 2Nd Btr Cam Assembly Removal (Pl8.1.10)
EPSON ColorPage EPL-C8200 Revision A 3.2.11.6 2ND BTR CAM ASSEMBLY Removal (PL8.1.10) 18. Remove 3 screws (gold, cup head, 4mm) securing the 2ND BTR CAM ASSEMBLY. 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) NOTE: In the following step, be careful not to drop and lose the BTR 2.
Page 215: Auger High Assembly Removal (Pl8.1.40)
EPSON ColorPage EPL-C8200 Revision A 3.2.11.7 AUGER HIGH ASSEMBLY Removal (PL8.1.40) 18. Remove the RIGHT COVER ASSEMBLY. (See Section 3.2.4.8.) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 19. Remove the CONTROLLER PWB. (See Section 3.2.17.1.) 2. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 20.
Page 216 EPSON ColorPage EPL-C8200 Revision A 23. Remove the screw (gold, cup head, 8mm) and the E-ring securing the AUGER HIGH ASSEMBLY at the left inner side (lower) of the printer. 24. Remove the screw (gold, 6mm) securing the AUGER HIGH ASSEMBLY at the middle inner side (upper) of the printer.
Page 217: Ibt Belt Assembly Removal (Pl8.2.2)
EPSON ColorPage EPL-C8200 Revision A 3.2.11.8 IBT BELT ASSEMBLY Removal (PL8.2.2) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 2. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 3. Remove the DRUM CARTRIDGE. (See Section 3.2.9.1.) 4. Remove the TENSION LEVER. (See Section 3.2.11.1.) 5.
Page 218 EPSON ColorPage EPL-C8200 Revision A 18. Remove the IBT BELT ASSEMBLY from the TRANSFER ASSEMBLY. Figure 3-91. IBT BELT ASSEMBLY Removal (3/3) When installing the IBT BELT ASSEMBLY, be careful not to damage or stain it. Before installing the PUSH IN SHAFT, clean the shaft to remove any oil and foreign matter.
Page 219: Tro Sensor Removal (Pl8.2.12)
EPSON ColorPage EPL-C8200 Revision A 3.2.11.9 TRO SENSOR Removal (PL8.2.12) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 2. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 3. Remove the DRUM CARTRIDGE. (See Section 3.2.9.1.) 4. Remove the TENSION LEVER. (See Section 3.2.11.1.) 5.
Page 220: Fusing
EPSON ColorPage EPL-C8200 Revision A 3.2.12 Fusing 3.2.12.2 FUSER ASSEMBLY Removal (PL9.1.1) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 3.2.12.1 OIL ROLL ASSEMBLY Removal (PL9.1.10) 2. Draw out the UNIVERSAL TRAY. 1. Draw out the FUSER ASSEMBLY. 3. Draw out the FUSER ASSEMBLY.
Page 221: Main Fuser Assembly Removal (Pl9.1.2)
EPSON ColorPage EPL-C8200 Revision A 3.2.12.3 MAIN FUSER ASSEMBLY Removal (PL9.1.2) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 2. Remove the OIL ROLL ASSEMBLY. (See Section 3.2.12.1.) 3. Remove the FUSER ASSEMBLY. (See Section 3.2.12.2.) 4. Disconnect 2 connectors (P/J72B, P/J79) for the MAIN FUSER ASSEMBLY.
Page 222: Fuser Upper Assembly Removal (Pl9.2.23)
EPSON ColorPage EPL-C8200 Revision A 3.2.12.4 FUSER UPPER ASSEMBLY Removal (PL9.2.23) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 2. Remove the OIL ROLL ASSEMBLY. (See Section 3.2.12.1.) 3. Remove the FUSER ASSEMBLY. (See Section 3.2.12.2.) 4. Remove the MAIN FUSER ASSEMBLY. (See Section 3.2.12.3.) NOTE: In the following step, be careful not to damage the HEAT ROLL surface with a driver when remove the TEMP.
Page 223: H/R Heater Removal (Pl9.2.20)
EPSON ColorPage EPL-C8200 Revision A 3.2.12.5 H/R HEATER Removal (PL9.2.20) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 2. Remove the OIL ROLL ASSEMBLY. (See Section 3.2.12.1.) 3. Remove the FUSER ASSEMBLY. (See Section 3.2.12.2.) 4. Remove the MAIN FUSER ASSEMBLY. (See Section 3.2.12.3.) 5.
Page 224: P/R Heater Removal (Pl9.2.19)
EPSON ColorPage EPL-C8200 Revision A 3.2.12.6 P/R HEATER Removal (PL9.2.19) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 2. Remove the OIL ROLL ASSEMBLY. (See Section 3.2.12.1.) 3. Remove the FUSER ASSEMBLY. (See Section 3.2.12.2.) 4. Remove the MAIN FUSER ASSEMBLY. (See Section 3.2.12.3.) 5.
Page 225: Lower Guide Assembly Removal (Pl9.2.26)
EPSON ColorPage EPL-C8200 Revision A 3.2.12.7 LOWER GUIDE ASSEMBLY Removal (PL9.2.26) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 2. Remove the OIL ROLL ASSEMBLY. (See Section 3.2.12.1.) 3. Remove the FUSER ASSEMBLY. (See Section 3.2.12.2.) 4. Remove the MAIN FUSER ASSEMBLY. (See Section 3.2.12.3.) 5.
Page 226: Fuser Exit Sensor Removal (Pl9.2.25)
EPSON ColorPage EPL-C8200 Revision A 3.2.12.8 FUSER EXIT SENSOR Removal (PL9.2.25) 3.2.12.9 UPPER GUIDE ASSEMBLY Removal (PL9.2.32) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 2. Remove the OIL ROLL ASSEMBLY. (See Section 3.2.12.1.) 2.
Page 227: Heat Roll Removal (Pl9.2.12)
EPSON ColorPage EPL-C8200 Revision A 3.2.12.10 HEAT ROLL Removal (PL9.2.12) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 2. Remove the OIL ROLL ASSEMBLY. (See Section 3.2.12.1.) 3. Remove the FUSER ASSEMBLY. (See Section 3.2.12.2.) 4. Remove the MAIN FUSER ASSEMBLY. (See Section 3.2.12.3.) 5.
Page 228: Pressure Roll Removal (Pl9.2.9)
EPSON ColorPage EPL-C8200 Revision A 3.2.12.11 PRESSURE ROLL Removal (PL9.2.9) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 2. Remove the OIL ROLL ASSEMBLY. (See Section 3.2.12.1.) 3. Remove the FUSER ASSEMBLY. (See Section 3.2.12.2.) 4. Remove the MAIN FUSER ASSEMBLY. (See Section 3.2.12.3.) 5.
Page 229: Temp. Sensor Assembly Removal (Pl9.2.24)
EPSON ColorPage EPL-C8200 Revision A 3.2.12.12 TEMP. SENSOR ASSEMBLY Removal (PL9.2.24) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 2. Remove the OIL ROLL ASSEMBLY. (See Section 3.2.12.1.) 3. Remove the FUSER ASSEMBLY. (See Section 3.2.12.2.) 4. Remove the MAIN FUSER ASSEMBLY. (See Section 3.2.12.3.) 5.
Page 230: Exchange Chute Removal (Pl9.3.10)
EPSON ColorPage EPL-C8200 Revision A 3.2.12.13 EXCHANGE CHUTE Removal (PL9.3.10) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 2. Remove the OIL ROLL ASSEMBLY. (See Section 3.2.12.1.) 3. Remove the FUSER ASSEMBLY. (See Section 3.2.12.2.) 4. Remove the MAIN FUSER ASSEMBLY. (See Section 3.2.12.3.) 5.
Page 231: Oil Cam Solenoid Removal (Pl9.3.21)
EPSON ColorPage EPL-C8200 Revision A 3.2.12.14 OIL CAM SOLENOID Removal (PL9.3.21) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 2. Remove the OIL ROLL ASSEMBLY. (See Section 3.2.12.1.) 3. Remove the FUSER ASSEMBLY. (See Section 3.2.12.2.) 4. Remove the MAIN FUSER ASSEMBLY. (See Section 3.2.12.3.) NOTE: In the following step, FUSER REAR RAIL will be kept connected to the FUSER TRAY ASSEMBLY.
Page 232: Exchange Solenoid Removal (Pl9.3.16)
EPSON ColorPage EPL-C8200 Revision A 3.2.12.15 EXCHANGE SOLENOID Removal (PL9.3.16) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 2. Remove the OIL ROLL ASSEMBLY. (See Section 3.2.12.1.) 3. Remove the FUSER ASSEMBLY. (See Section 3.2.12.2.) 4. Remove the MAIN FUSER ASSEMBLY. (See Section 3.2.12.3.) 5.
Page 233: Oil Cam Assembly Removal (Pl9.3.22)
EPSON ColorPage EPL-C8200 Revision A 3.2.12.16 OIL CAM ASSEMBLY Removal (PL9.3.22) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 2. Remove the OIL ROLL ASSEMBLY. (See Section 3.2.12.1.) 3. Remove the FUSER ASSEMBLY. (See Section 3.2.12.2.) 4. Remove the MAIN FUSER ASSEMBLY. (See Section 3.2.12.3.) 5.
Page 234: Cleaner Cam Solenoid Removal (Pl9.4.23)
EPSON ColorPage EPL-C8200 Revision A 3.2.12.17 CLEANER CAM SOLENOID Removal (PL9.4.23) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 2. Remove the OIL ROLL ASSEMBLY. (See Section 3.2.12.1.) 3. Remove the FUSER ASSEMBLY. (See Section 3.2.12.2.) 4. Remove the MAIN FUSER ASSEMBLY. (See Section 3.2.12.3.)
Page 235: Cleaner Cam Assembly Removal (Pl9.4.26)
EPSON ColorPage EPL-C8200 Revision A 3.2.12.18 CLEANER CAM ASSEMBLY Removal (PL9.4.26) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 2. Remove the OIL ROLL ASSEMBLY. (See Section 3.2.12.1.) 3. Remove the FUSER ASSEMBLY. (See Section 3.2.12.2.) 4. Remove the MAIN FUSER ASSEMBLY. (See Section 3.2.12.3.) 5.
Page 236: Roll Assembly Removal (Pl9.3.7)
EPSON ColorPage EPL-C8200 Revision A 3.2.12.19 EXIT-1 ROLL ASSEMBLY Removal (PL9.3.7) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 2. Remove the OIL ROLL ASSEMBLY. (See Section 3.2.12.1.) 3. Remove the FUSER ASSEMBLY. (See Section 3.2.12.2.) 4. Remove the MAIN FUSER ASSEMBLY. (See Section 3.2.12.3.) 5.
Page 237: Cru Switch Assembly Removal (Pl9.3.25)
EPSON ColorPage EPL-C8200 Revision A 3.2.12.20 CRU SWITCH ASSEMBLY Removal (PL9.3.25) 1. Remove the EXIT TRAY ASSEMBLY. (See Section 3.2.13.1.) 2. Remove the OIL ROLL ASSEMBLY. (See Section 3.2.12.1.) 3. Remove the FUSER ASSEMBLY. (See Section 3.2.12.2.) 4. Remove the MAIN FUSER ASSEMBLY. (See Section 3.2.12.3.) 5.
Page 238: Paper Exit
EPSON ColorPage EPL-C8200 Revision A 3.2.13 Paper Exit 3.2.13.2 EXIT UPPER ASSEMBLY Removal (PL10.1.2) 1. Open the exit upper assembly. 3.2.13.1 EXIT TRAY ASSEMBLY Removal (PL10.1.10) NOTE: In the following step, be careful not to break the hinge in the 1.
Page 239: Exit Lower Assembly Removal (Pl10.1.1)
EPSON ColorPage EPL-C8200 Revision A 3.2.13.3 EXIT LOWER ASSEMBLY Removal (PL10.1.1) 3.2.13.4 EXIT-2 ROLL ASSEMBLY Removal (PL10.2.5) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 2. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 2.
Page 240: Roll Assembly Removal (Pl10.2.7)
EPSON ColorPage EPL-C8200 Revision A 3.2.13.5 EXIT-3 ROLL ASSEMBLY Removal (PL10.2.7) 3.2.13.6 FUSER FAN Removal (PL10.2.15) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 1. Draw out the FUSER ASSEMBLY. 2. Remove front and rear E-rings securing the EXIT-3 ROLL 2.
Page 241: Top Exit Sensor Removal (Pl10.2.12)
EPSON ColorPage EPL-C8200 Revision A 3.2.13.7 TOP EXIT SENSOR Removal (PL10.2.12) 3.2.13.8 EXIT CHUTE SWITCH Removal (PL10.2.13) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 2. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 2.
Page 242: Drive
EPSON ColorPage EPL-C8200 Revision A 3.2.14 Drive 5. Remove 5 screws (black, cup head, 10mm) securing the P/H DRIVE ASSEMBLY, and remove the P/H DRIVE ASSEMBLY along with 2 DRIVE CLAMP-Ys. 3.2.14.1 P/H DRIVE ASSEMBLY Removal (PL11.1.1) 6. Remove the both 2 DRIVE CLAMP-Ys from the P/H DRIVE 1.
Page 243: P/H Motor Assembly Removal (Pl11.1.3)
EPSON ColorPage EPL-C8200 Revision A 3.2.14.2 P/H MOTOR ASSEMBLY Removal (PL11.1.3) 3.2.14.3 ROTARY MOTOR PWB Removal (PL11.1.21) 1. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 1. Remove the REAR COVER ASSEMBLY.(See Section 3.2.4.5.) NOTE: In the following step, the ROTARY MOTOR PWB will be 2.
Page 244: Rotary Motor Assembly Removal (Pl11.1.20)
EPSON ColorPage EPL-C8200 Revision A 3.2.14.4 ROTARY MOTOR ASSEMBLY Removal (PL11.1.20) 1. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 2. Disconnect the connector (P/J247) for the ROTARY MOTOR ASSEMBLY. 3. Remove 3 screws (gold, 6mm) securing the ROTARY MOTOR ASSEMBLY and remove the ROTARY MOTOR ASSEMBLY.
Page 245: Dispense Motor Assembly Removal (Pl11.1.22)
EPSON ColorPage EPL-C8200 Revision A 3.2.14.5 DISPENSE MOTOR ASSEMBLY Removal (PL11.1.22) 1. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 2. Remove the P/H MOTOR ASSEMBLY. (See Section 3.2.14.2.) 3. Remove the ROTARY MOTOR PWB. (See Section 3.2.14.3.) 4. Remove the ROTARY MOTOR ASSEMBLY. (See Section 3.2.14.4.)
Page 246: Fuser Drive Assembly Removal (Pl11.1.2)
EPSON ColorPage EPL-C8200 Revision A 3.2.14.6 FUSER DRIVE ASSEMBLY Removal (PL11.1.2) 1. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 2. Remove the FUSER ASSEMBLY with the EXIT TRAY ASSEMBLY and the OIL ROLL ASSEMBLY on it. (See Section 3.2.12.2.) 3.
Page 247: Process Motor Assembly Removal
EPSON ColorPage EPL-C8200 Revision A 3.2.14.7 PROCESS MOTOR ASSEMBLY Removal (PL11.1.12 1. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 2. Disconnect 2 connectors (P/J51 and P/J52) for the PROCESS MOTOR ASSEMBLY. 3. Remove 4 screws (gold, 8mm) securing the PROCESS MOTOR ASSEMBLY, and remove the PROCESS MOTOR ASSEMBLY.
Page 248: Process Drive Assembly Removal (Pl11.1.10)
EPSON ColorPage EPL-C8200 Revision A 3.2.14.8 PROCESS DRIVE ASSEMBLY Removal (PL11.1.10) 17. Remove 7 screws (black, cup head, 8mm) securing the PROCESS DRIVE ASSEMBLY and remove the PROCESS DRIVE 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) ASSEMBLY. 2. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 3.Remove the DRUM CARTRIDGE.
Page 249: Deve. Clutch Assembly Removal (Pl11.1.23)
EPSON ColorPage EPL-C8200 Revision A 3.2.14.9 DEVE. CLUTCH ASSEMBLY Removal (PL11.1.23) 1. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 2. Remove the FUSER ASSEMBLY with the EXIT TRAY ASSEMBLY and the OIL ROLL ASSEMBLY installed on it. (See Section 3.2.12.2.)
Page 250: Frame
EPSON ColorPage EPL-C8200 Revision A 3.2.15 Frame 3.2.15.1 DEVE. TIE PLATE Removal (PL12.1.4) 1. Remove the FRONT COVER ASSEMBLY. (See Section 3.2.4.1.) 2. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 3. Remove the DRUM CARTRIDGE. (See Section 3.2.9.1.) 4. Remove the TENSION LEVER. (See Section 3.2.11.1.) 5.
Page 251: Electrical
EPSON ColorPage EPL-C8200 Revision A 3.2.16 Electrical 3.2.16.1 LVPS Removal (PL13.1.1) 1. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 2. Disconnect 3 connectors (P/J32, P/J33, P/J35) for the LVPS and release the harnesses from the clamp. 3. Remove 4 screws (silver, cup head, 8mm) securing the LVPS.
Page 252: Hvps Removal (Pl13.1.2)
EPSON ColorPage EPL-C8200 Revision A 3.2.16.2 HVPS Removal (PL13.1.2) 3.2.16.3 TOP COVER SWITCH Removal (PL13.1.3) 1. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 2. Disconnect 7 connectors (P/J41, P/J42, P/JA, P/JC, P/JD, P/JF, P/ 2.
Page 253: Deve. Fan Removal (Pl13.1.5)
EPSON ColorPage EPL-C8200 Revision A 3.2.16.4 DEVE. FAN Removal (PL13.1.5) 1. Remove the REAR COVER ASSEMBLY. (See Section 3.2.4.5.) 2. Disconnect the connector (P/J82) for the DEVE. FAN and release the harness from the FAN DUCT. 3. Widen the hooks on the FAN DUCT and remove the DEVE. FAN.
Page 254: Mcu Pwb Removal (Pl13.2.1)
EPSON ColorPage EPL-C8200 Revision A 3.2.16.5 MCU PWB Removal (PL13.2.1) When replacing the MCU PWB, perform the following operations referring to Chapter 4 “Diagnostics”. Read data prior to replacement, then write the read data when the replacement is completed. Perform “NVM Write” after replacement.
Page 255: Communication Assembly Removal (Pl13.2.2)
EPSON ColorPage EPL-C8200 Revision A 3.2.16.6 COMMUNICATION ASSEMBLY Removal (PL13.2.2) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 2. Remove the RIGHT COVER ASSEMBLY. (See Section 3.2.4.8.) 3. Draw out the MAIN P/H ASSEMBLY. 4. Remove the CONTROLLER PWB. (See Section 3.2.17.1.) 5.
Page 256: Front Cover Switch R Removal (Pl13.2.3)
EPSON ColorPage EPL-C8200 Revision A 3.2.16.7 FRONT COVER SWITCH R Removal (PL13.2.3) 1. Remove the DRUM CARTRIDGE. (See Section 3.2.9.1.) 2. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 3. Remove the TENSION LEVER. (See Section 3.2.11.1.) 4. Remove the INNER COVER ASSEMBLY. (See Section 3.2.4.3.) 5.
Page 257: Front Cover Switch L Removal (Pl13.2.4)
EPSON ColorPage EPL-C8200 Revision A 3.2.16.8 FRONT COVER SWITCH L Removal (PL13.2.4) 1. Remove the DRUM CARTRIDGE. (See Section 3.2.9.1.) 2. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 3. Remove the TENSION LEVER. (See Section 3.2.11.1.) 4. Remove the INNER COVER ASSEMBLY. (See Section 3.2.4.3.) 5.
Page 258: Environment Sensor Removal (Pl13.2.5)
EPSON ColorPage EPL-C8200 Revision A 3.2.16.9 ENVIRONMENT SENSOR Removal (PL13.2.5) 1. Remove the MSI TRAY ASSEMBLY. (See Section 3.2.7.1.) 2. Remove the MAIN P/H ASSEMBLY along with the MSI ASSEMBLY. (See Section 3.2.8.1.) 3. Disconnect the connector (P/J105) for the ENVIRONMENT SENSOR and release the harness from the clamp.
Page 259: Controller
EPSON ColorPage EPL-C8200 Revision A 3.2.17 Controller 3.2.17.1 CONTROLLER PWB Removal (PL 14.1.10) 1. Remove the RIGHT COVER ASSEMBLY. (See Section 3.2.4.8.) 2. Disconnect 2 connectors (P/J310 and P/J314) for the CONTROLLER PWB. 3. Remove 8 screws (silver, cup head, 8mm) securing the CONTROLLER PWB by the bottom area.
Page 260: Controller Fan Removal (Pl 14.1.2)
EPSON ColorPage EPL-C8200 Revision A 3.2.17.2 CONTROLLER FAN Removal (PL 14.1.2) 3.2.17.3 CONT. CHASSIS ASSEMBLY Removal (PL 14.1.1) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 1. Remove the TOP COVER ASSEMBLY. (See Section 3.2.4.3.) 2. Remove the RIGHT COVER ASSEMBLY. (See Section 3.2.4.8.) 2.
Page 261: Adjustment
EPSON ColorPage EPL-C8200 Revision A 3.3 Adjustment 5. Install the MAIN FUSER ASSEMBLY and the OIL ROLL ASSEMBLY, and close the FUSER ASSEMBLY. This section describes how to maintain the proper fuser level, which is 6. Print a solid black belt (approximately 80mm 289mm) in a A-4 required for stable paper feeding.
Page 262 EPSON ColorPage EPL-C8200 Revision A 10. See the output and check that the darkness of the area which was 11. If the result is not satisfactory, return to the step 4 and turn the NIP pressed has changed. Measure the width of the changed area at the...
Page 263 DIAGNOSTICS...
Page 264 Table of Contents Overview....................1 Digital Output Test: Device codes ..........27 Analog Input Test ..............31 Test print by MCU PWB ..............1 Analog Input Test: Device codes ..........32 Test Print Pattern ................2 Analog Output Test ..............33 Diagnostics by the Diagnostic Commander ........
Page 265: Overview
EPSON ColorPage EPL-C8200 Revision A 4.1 Overview NOTE: When disconnecting the short connector or turning the DIP switch off, do not touch any other components. You can perform a test print by using off-line diagnostics to check the NOTE: The paper feeder is selected with the previous panel setting.
Page 266: Test Print Pattern
EPSON ColorPage EPL-C8200 Revision A 4.1.2 Test Print Pattern The off-line diagnostic prints out the pattern shown below. (Four colors are printed on one page - One color on each quarter of the page) NOTE: The black portion of the test print may runover from the paper depending on the printer specifications.
Page 267: Diagnostics By The Diagnostic Commander
MCU PWB. NOTE: The Diagnostic PWB, RS-232C cable, personal computer, and Diagnostic Commander are collectively called the diagnostic tool (maintenance tool). Diagnostic tool provided by SEIKO EPSON is as shown in the following table: Table 4-1. Diagnostic Commander Tools...
Page 268: Diagnostic Commander
EPSON ColorPage EPL-C8200 Revision A 4.2.1.2 Diagnostic Commander 4.2.1.3 Diagnostic PWB The Diagnostic Commander takes the place of the Printer Controller The following components are mounted on the Diagnostic PWB: (CONTROLLER PWB) and controls the printer by sending and Connector to the MCU PWB.
Page 269: Command/Status
EPSON ColorPage EPL-C8200 Revision A 4.2.2 Command/Status 4.2.2.2 Data Format 4.2.2.1 Introduction The commands and statuse are exchanged between the Printer Controller and MCU PWB. Using the data (commands and statuse), the Printer Controller controls the printer. NOTE: The communication direction of the commands and statuse are...
Page 270: Command/Status Categories
EPSON ColorPage EPL-C8200 Revision A 4.2.2.3 Command/Status Categories 4.2.3 Preparation Commands and status are categorized into 4 groups according to the 4.2.3.1 Personal Computer printer controls. Use a personal computer that can run the Diagnostic Commander and (1) Paper, Media & Output Control set the communication port (RS-232C).
Page 271: Installing The Diagnostic Commander
EPSON ColorPage EPL-C8200 Revision A 4.2.3.2 Installing the Diagnostic Commander 4.2.3.3 Uninstalling the Diagnostic Commander The following describes how to install the Diagnostic Commander: The following describes how to uninstall the Diagnostic Commander in the computer. 1. Start Windows 95. Select [Start] > [Settings] > [Control Panel].
Page 272: Connecting The Diagnostic Tool
EPSON ColorPage EPL-C8200 Revision A 4.2.3.4 Connecting the Diagnostic Tool The following describes how to connect the diagnostic tool. 1. Remove the RIGHT COVER ASSEMBLY. (See Chapter 3.) 2. Remove the Controller PWB. (See Chapter 3.) NOTE:In the following procedures, makes sure that the soldered side of the Diagnostic PWB do not touch the Chassis Assembly.
Page 273: Diagnostic Commander: Operations
EPSON ColorPage EPL-C8200 Revision A 4.2.4 Diagnostic Commander: Operations 4.2.4.2 Setting Up the Communication Establish communication between the computer and the Diagnostic 4.2.4.1 Starting the Diagnostic Commander Commander as follows: Start/End the Diagnostic Commander as follows: 1. Select [Manual] or [Auto] depending on the menu you want to select.
Page 274: Sending/Receiving Commands/Status
EPSON ColorPage EPL-C8200 Revision A A single click only displays the command code in the 4.2.4.3 Sending/receiving commands/status [Command] box. NOTE: A command must be sent after the communication has been established. NOTE: For details, Section 4.2.7 “Commands/Status List” in this section.
Page 275 EPSON ColorPage EPL-C8200 Revision A 6. As the same manner, the parameter code is displayed in the Inputting a Command Directly in the [Command] Box. [Command] box. When you select a parameter code from the list, if you double-click the command code and the command code does...
Page 276: Automatically Executing A Command
EPSON ColorPage EPL-C8200 Revision A 4.2.4.4 Automatically executing a command Creating an Automatic Command Execution File NOTE: A command must be sent after the communication has been NOTE: Use an editor (e.g., WordPad, etc.) to create a file. established. NOTE: If you want to automatically execute a command, you need to As shown in the figure below, enter a command in HEX on one line.
Page 277: Service] Tab
EPSON ColorPage EPL-C8200 Revision A 4.2.4.5 [Service] tab NVM Write On the [Service] tab page, you can write data (specifications) in the You can write data (specifications) in the MCU PWB EEPROM (NVM). MCU PWB EEPROM (NVM), set a password, read/write the Master and read/initialize the Slave.
Page 278 EPSON ColorPage EPL-C8200 Revision A Master Read In the [Master Read] page, you can read the contents of the [Master]. NOTE: Before you run [Master Read], make sure that the communication has been established. If you run [Master Read] when the communication has not been established, the Diagnostic Commander may hang up.
Page 279 EPSON ColorPage EPL-C8200 Revision A Slave Read Slave Initialize In the [Slave Read] page, you can read the contents of the [Slave]. In the [Slave Initialize] page, you can initialize (erase) the [Slave] data. NOTE: Before you run [Slave Read], make sure that the communication Do not run [Slave Initialize] unless instructed to do so has been established.
Page 280: Displaying The Log
EPSON ColorPage EPL-C8200 Revision A 4.2.4.6 Displaying the log The communication has been established Status The communication log shows you how the commands and status are Command exchanged between the Diagnostic Commander and the MCU PWB. Run [Log Window] to see the log.
Page 281: Life Counter Read/Write
EPSON ColorPage EPL-C8200 Revision A 4.2.5 Life Counter Read/Write 4.2.5.1 Read You can read the life counter data from the MCU PWB EEPROM (NVM) Table 4-9. Life Counter Read Specifications or write the data in the EEPROM (NVM) using the Parameter Control...
Page 282: Write
EPSON ColorPage EPL-C8200 Revision A 4.2.5.2 Write Table 4-10. Life Counter Write Specifications Item Command Note Drum Cartridge 80 00 V1 V2 V3 V4 Do not send this command if the printer has the CRUM function. Clear the counter if you replace...
Page 283: Executing Diagnostics
EPSON ColorPage EPL-C8200 Revision A 4.2.6 Executing Diagnostics 4.2.6.2 Diagnostics functions There are a total of 8 diagnostic functions (9 if you include the 4.2.6.1 Diagnostic execution steps diagnostics stop function). Run the diagnostics by sending the following command using the Table 4-11.
Page 284: Test Print
EPSON ColorPage EPL-C8200 Revision A 4.2.6.3 Test Print Example) Command You can set the parameters for the built-in test print function. 00 05 Table 4-12. Test Print Parameters All colors (YMCBk) DIAGON command: 75 DIAGOFF command: 76 Patches DIAGSTART command (Test Print): 90 00 XX XX...
Page 285: Digital Input Test
EPSON ColorPage EPL-C8200 Revision A 4.2.6.4 Digital Input Test Patch Test Print Pattern You can detect the High/Low level in the signals output from a switch or The printer prints the patch test print patterns (Cin50% patch) as shown sensor that has a digital signal.
Page 286: Digital Input Test: Device Codes
EPSON ColorPage EPL-C8200 Revision A 4.2.6.5 Digital Input Test: Device codes Table 4-14. Digital Input Test Device Codes (1/7) Table 4-15. Digital Input Test Device Codes (2/7) Digital Input Test [DIAGSTART: 90 01 XX, DIAGSTOP: Unnecessary] Digital Input Test [DIAGSTART: 90 01 XX, DIAGSTOP: Unnecessary]...
Page 287 EPSON ColorPage EPL-C8200 Revision A Table 4-16. Digital Input Test Device Codes (3/7) Table 4-17. Digital Input Test Device Codes (4/7) Digital Input Test [DIAGSTART: 90 01 XX, DIAGSTOP: Unnecessary] Digital Input Test [DIAGSTART: 90 01 XX, DIAGSTOP: Unnecessary] Function item...
Page 288 EPSON ColorPage EPL-C8200 Revision A Table 4-18. Digital Input Test Device Codes (5/7) Table 4-19. Digital Input Test Device Codes (6/7) Digital Input Test [DIAGSTART: 90 01 XX, DIAGSTOP: Unnecessary] Digital Input Test [DIAGSTART: 90 01 XX, DIAGSTOP: Unnecessary] Function item...
Page 289 EPSON ColorPage EPL-C8200 Revision A Table 4-20. Digital Input Test Device Codes (7/7) Digital Input Test [DIAGSTART: 90 01 XX, DIAGSTOP: Unnecessary] Function item Code Name Check (Hex) Status data: High Size Switch Assembly (Cassette 2) OPT_SIZE2 * [2] SIZE SWITCH...
Page 290: Digital Output Test
EPSON ColorPage EPL-C8200 Revision A 4.2.6.6 Digital Output Test NOTE: While the Process Motor Assembly, P/H Motor Assembly and Developer Clutch Assembly are on, and the Developer Components controlled by the digital signals can be turned ON/OFF. Assembly is in the development position, do not turn on the DB Table 4-21.
Page 291: Digital Output Test: Device Codes
EPSON ColorPage EPL-C8200 Revision A 4.2.6.7 Digital Output Test: Device codes Table 4-23. Device Codes for Digital Output Test (2/8) Digital Output Test [DIAGSTART: 90 02 XX, DIAGSTOP: 91 02 XX] If there is a <Warning!> or <Caution!> in the Check...
Page 292 EPSON ColorPage EPL-C8200 Revision A If there is a <Warning!> or <Caution!> in the Check Table 4-25. Device Codes for Digital Output Test (4/8) column, first confirm the warnings and cautions listed on the previous page to prevent problems. Digital Output Test [DIAGSTART: 90 02 XX, DIAGSTOP: 91 02 XX] Table 4-24.
Page 293 EPSON ColorPage EPL-C8200 Revision A Table 4-27. Device Codes for Digital Output Test (6/8) If there is a <Warning!> or <Caution!> in the Check column, first confirm the warnings and cautions listed Digital Output Test [DIAGSTART: 90 02 XX, DIAGSTOP: 91 02 XX] on the previous page to prevent problems.
Page 294 EPSON ColorPage EPL-C8200 Revision A Table 4-29. Device Codes for Digital Output Test (8/8) If there is a <Warning!> or <Caution!> in the Check column, first confirm the warnings and cautions listed Digital Output Test [DIAGSTART: 90 02 XX, DIAGSTOP: 91 02 XX] on the previous page to prevent problems.
Page 295: Analog Input Test
EPSON ColorPage EPL-C8200 Revision A 4.2.6.8 Analog Input Test NOTE: The status data consists of 2 bytes; the lower byte is displayed first. You can run this test to detect the signal levels of the sensors and output monitors that output an analog signal.
Page 296: Analog Input Test: Device Codes
EPSON ColorPage EPL-C8200 Revision A 4.2.6.9 Analog Input Test: Device codes Table 4-32. Device Codes of the analog Input Test (2/2) If there is a <Warning!> or <Caution!> in the Check column, Analog Output Test [DIAGSTART: 90 03 XX, DIAGSTOP: Unnecessary] first confirm the warnings and cautions listed on the previous page to prevent problem.
Page 297: Analog Output Test
EPSON ColorPage EPL-C8200 Revision A 4.2.6.10 Analog Output Test Do not touch live parts when high voltages are output. Components controlled by the analog signals can be turned ON/OFF. Install all covers when the laser beam is active and exposed.
Page 298: Analog Output Test: Device Codes
EPSON ColorPage EPL-C8200 Revision A 4.2.6.11 Analog Output Test: Device codes Table 4-35. Analog Output Test: Device codes (2/2) Analog Output Test [DIAGSTART: 90 04 XX, DIAGSTOP: 91 04 XX XX] If there is a <Warning!> or <Caution!> in the Check...
Page 299: Eeprom Read
EPSON ColorPage EPL-C8200 Revision A 4.2.6.12 EEPROM Read You can read and check the data in the MCU PWB EEPROM (NVM). Example) Command A0 86 01 00 05 CC Table 4-36. EEPROM Read Parameters Data: 100000 (186A0h) DIAGON command: 75...
Page 300 EPSON ColorPage EPL-C8200 Revision A Before replacing the MCU PWB, make sure to read and If you replace a periodically replaced parts (i.e., Main record the following NVM numbers: Fuser Assembly, 2nd BTR Assembly, Belt Cleaner Assembly) or the Drum Cartridge for the printer 60 (0044h): Oil Rate count (accumulated counts) to detect the Oil without the CRUM function, write “0”...
Page 301: Eeprom Write
EPSON ColorPage EPL-C8200 Revision A 4.2.6.13 EEPROM Write NOTE: Enter the lower byte of the 2 bytes in the Code_EP (NVM number) first, then enter the second byte. You can change the data in the MCU PWB EEPROM (NVM) by writing NOTE: Enter the lowest byte of the 4 bytes in the status data first, then new data in it.
Page 302 EPSON ColorPage EPL-C8200 Revision A If you replace a periodically replaced parts (i.e., Main Fuser Assembly or 2nd BTR Assembly) or the Drum Cartridge for the printer without the CRUM function, write “0” in the following NVM number data. (Setting a “0”...
Page 303: Eeprom Initialize
EPSON ColorPage EPL-C8200 Revision A 4.2.6.14 EEPROM Initialize Example) Command You can initialize the MCU PWB EEPROM (NVM). 90 07 Do not initialize the EEPROM unless instructed to do so in this manual. EEPROM Initialize DIAGSTART command If you initialize the EEPROM, do the following: Example) Status Read the NVM numbers using the EEPROM Read.
Page 304: Nvm List
EPSON ColorPage EPL-C8200 Revision A 4.2.6.15 NVM List Table 4-39. NVM List (1/8) EEPROM Read [90 05 XX XX], The NVM numbers that are not listed in the table EEPROM Write [90 06 XX XX XX XX XX XX] below are used by the system.
Page 305 EPSON ColorPage EPL-C8200 Revision A Table 4-40. NVM List (2/8) Table 4-41. NVM List (3/8) EEPROM Read [90 05 XX XX], EEPROM Read [90 05 XX XX], EEPROM Write [90 06 XX XX XX XX XX XX] EEPROM Write [90 06 XX XX XX XX XX XX]...
Page 306 EPSON ColorPage EPL-C8200 Revision A Table 4-42. NVM List (4/8) Table 4-43. NVM List (5/8) EEPROM Read [90 05 XX XX], EEPROM Read [90 05 XX XX], EEPROM Write [90 06 XX XX XX XX XX XX] EEPROM Write [90 06 XX XX XX XX XX XX]...
Page 307 EPSON ColorPage EPL-C8200 Revision A Table 4-44. NVM List (6/8) Table 4-45. NVM List (7/8) EEPROM Read [90 05 XX XX], EEPROM Read [90 05 XX XX], EEPROM Write [90 06 XX XX XX XX XX XX] EEPROM Write [90 06 XX XX XX XX XX XX]...
Page 308 EPSON ColorPage EPL-C8200 Revision A Table 4-46. NVM List (8/8) EEPROM Read [90 05 XX XX], EEPROM Write [90 06 XX XX XX XX XX XX] Range Access Function Default (Hex) Permission Number (Hex) Yes/No (Hex) Data Unit Toner Cartridge C: Life...
Page 309: Commands/Status List
EPSON ColorPage EPL-C8200 Revision A 4.2.7 Commands/Status List (2) Status Table 4-48. Status List 4.2.7.1 Paper, Media & Output Control Status Name code Parameter code Description (1) Commands (Hex) Table 4-47. Command List 1. DEST, 2. DOPT, PPOUT % Paper ejection data 3.
Page 310 EPSON ColorPage EPL-C8200 Revision A Table 4-50. Parameter Code Description (2/2) CASSETTE SIZE MEDIA DEST DOPT Data Detect in the Paper size setting SEF/ Detect in the Optional (Hex) Cassette Paper size Paper type Cassette Destination Enable/Disable Cassette stacker Enable/Disable...
Page 311: Printing/Status Control
EPSON ColorPage EPL-C8200 Revision A 4.2.7.2 Printing/Status Control (1) Commands Table 4-51. Command List of the Printing/Status Control Command Parameter Name Description code (Hex) code 1. PMODE, 2. CMODE PFC # Requests paper. 3. SHEET PMSTT # None Requests to start Scanner Motor rotation.
Page 312 EPSON ColorPage EPL-C8200 Revision A (2) Status Table 4-52. Status List of the Printing/Status Control Status code Parameter Name Description (Hex) code 1. AMODE PFA % 2. SHEET1 Allows paper feed. 3. SHEET2 ENGERR % None Printer error. ERRRV % None Cancels the printer error.
Page 313 EPSON ColorPage EPL-C8200 Revision A (3) Parameter codes SLPON command parameters Table 4-53. SLPON Command Parameters SLPON command code: 73 Data (Hex) SLEEPMODE LIGHT SLEEP mode DEEP SLEEP mode PFC command/PFA status parameters NOTE:The following parameters have been defined by bits.
Page 314 EPSON ColorPage EPL-C8200 Revision A SSENG status parameters SSCONS/SSTRAY/SSCRUM status parameters NOTE:The following parameters have been defined by bits. NOTE:The following parameters have been defined by bits. Table 4-55. SSENG Status Parameters Table 4-56. SSCONS/SSTRAY/SSCRUM Status Parameters SSENG status code: C0...
Page 315 EPSON ColorPage EPL-C8200 Revision A SSJAM status parameters SSHW status parameters NOTE:The following parameters have been defined by bits. NOTE:The following parameters have been defined by bits. Table 4-57. SSJAM Status Parameters Table 4-58. SSHW Status Parameters (1/2)
Page 316 EPSON ColorPage EPL-C8200 Revision A SSLIFE/SSOPEN status parameters SSWARN status parameters NOTE:The following parameters have been defined by bits. NOTE:The following parameters have been defined by bits. Table 4-60. SSLIFE/SSOPEN Status Parameters Table 4-61. SSWARN Status Parameters SSLIFE status code: C6...
Page 317: Parameter Control
EPSON ColorPage EPL-C8200 Revision A 4.2.7.3 Parameter Control Do not use any other commands except LIFCNTSET (80), CTLSET (85), LIFCNTR (D0), LIFLIMR (D1) and CTLSETR (D7) unless instructed to do so in this manual. Before replacing the MCU PWB, run the LIFCNTR (D0) and CTLSETR (D7).
Page 318 EPSON ColorPage EPL-C8200 Revision A (1) Commands Table 4-63. Command List of the Parameter Control (2/2) Table 4-62. Command List of the Parameter Control (1/2) Command Parameter Command Description Command Parameter code (Hex) code Command Description code (Hex) code Reads the minimum time-out TIMMINR 1.TIM...
Page 319 EPSON ColorPage EPL-C8200 Revision A (2) Status Table 4-64. Status List of the Parameter Control Status code Status Parameter code Description (Hex) [Response] Life counter 1.LIFE, 2.V1, 3.V2, 4.V3, 5.V4, LIFCNTR 6.V5, 7.V6, 8.V7, 9.V8 [Response] Life-over value 1.LIFE, 2.V1, 3.V2, 4.V3, 5.V4, LIFLIMR 6.V5, 7.V6, 8.V7, 9.V8...
Page 320 EPSON ColorPage EPL-C8200 Revision A (3) Parameter codes UNIT/ACCESS parameter codes NOTE:The contents of the ACCESS parameters have been defined by bits. Table 4-65. UNIT/ACCESS Parameter Codes (1/2) TIMUNITR status code: D3 Data (Hex) UNIT (Time Unit) Milliseconds Seconds...
Page 321 EPSON ColorPage EPL-C8200 Revision A LIFE/TIM/CTL/STC parameter codes Table 4-67. LIFE/TIM/CTL/STC Parameter Codes Command/ 83, 84, D2, D3, 80, D0, 81, 82, 88, 89, D1, DC, F0, F1 85, D7, 86, D6, D8, D9, AA, DE 87, D3 Status code...
Page 322: Diagnostics Control
EPSON ColorPage EPL-C8200 Revision A 4.2.7.4 Diagnostics control (1) Commands (2) Status Table 4-68. Command List of the Diagnostic Control Table 4-69. Status List of the Diagnostic Control Status Status Command code Parameter code Description Status code Parameter code Description...
Page 323 EPSON ColorPage EPL-C8200 Revision A REASON/OPTION parameter codes (3) Parameters DGTST parameter codes NOTE:The contents of the following parameters have been defined by bits. Table 4-70. DGTST parameter codes Table 4-72. REASON/OPTION parameter codes Data (Hex) DGTST (Diag Test)
Page 324: Error/Status Code
EPSON ColorPage EPL-C8200 Revision A 4.2.8 Error/Status Code Example) You can identify an error/status code of this printer from the following C1-04 statuse in the Printing/Status Control in the command/status category: SSENG, SSCONS, SSTRAY, SSJAM, SSHW, SSLIFE, SSOPEN and SSWARN.
Page 325: Transfer Mcu Pwb Board Nvram Engine Status To A New Board
EPSON ColorPage EPL-C8200 Revision A 4.2.9 Transfer MCU PWB Board NVRAM Engine Status to a New Board Follow the steps below to transfer the engine status data in the previous appears confirming that the “LOG file has been edited as AT file”...
Page 326 TROUBLESHOOTING...
Page 327 Table of Contents Overview....................1 FIP-1.28 P/H MOTOR Related Error ..........46 FIP-1.29 ENVIRONMENT SENSOR Related Error ......48 Troubleshooting Procedure............... 1 FIP-1.30 ROTARY MOTOR ASSY (HP Detection) Related Error .. 49 Self-Diagnostic Function by LCD Message ........1 FIP-1.31 WASTE TONER BOX is Out ..........50 Status Message ................
Page 328 FIP-2.8 MSI LONG N/P SENSOR is Defective ....... 77 5. White/Shady deletion lines appear vertically FIP-2.9 MSI EDGE SENSOR is Defective ........78 to the paper feeding direction ....116 FIP-2.10 MSI CLUTCH is Defective ..........79 6. Black/Color Spots ..............117 FIP-2.11 PICK UP SOLENOID is Defective ........
Page 329: Troubleshooting Procedure
EPSON ColorPage EPL-C8200 Revision A 5.1 Overview 5.1.2 Self-Diagnostic Function by LCD Message This printer is equipped with a self-diagnostic function. If the printer Types of error occur to a page printer vary widely, such as poor print detects an error, it indicates the error information with the LED lamps on quality or abnormal operation, and it makes identification of failed part the LCD panel.
Page 330 EPSON ColorPage EPL-C8200 Revision A Table 5-2. LCD Message List (2/3) Table 5-3. LCD Message List (3/3) LED Description LED Description Message Category Refer to: Message Category Refer to: On Line Continue On Line Continue Error Page 5-8 Status Page 5-3...
Page 331: Status Message
EPSON ColorPage EPL-C8200 Revision A 5.1.2.1 Status Message Reset To Save The printer shows the status message when: Appears when the print settings were changed during printing. Perform one of the following to clear the message. The printer is free from any error.
Page 332 EPSON ColorPage EPL-C8200 Revision A Offline The printer receives data and produces printing data but does not print. To return the printer to the ready status, press the On Line or Continue button. Note performing reset or rest all operation erases all printing data.
Page 333: Error Message
EPSON ColorPage EPL-C8200 Revision A < > 5.1.2.2 Error Message Remedy: Remove the jammed paper near the paper source Error messages are indicated according to priority. Therefore, if multiple and open the paper feeding unit (and the feeder errors have been detected, the message with the highest priority cover if Large Capacity Paper Unit or 500-Sheet appears in the LCD.
Page 334 EPSON ColorPage EPL-C8200 Revision A uuuu Toner Crtg Out Wrong Photoconductor LED: On Line = off, Continue = off LED: On Line = off, Continue = off Description: One or more Toner Cartridges are not installed. The Description: A wrong photoconductor unit is installed.
Page 335 EPSON ColorPage EPL-C8200 Revision A Replace Photocondctr Exit Cover Open LED: On Line = off, Continue = off LED: On Line = off, Continue = off Description: The engine has detected that the photoconductor Description: The exit cover is open.
Page 336 EPSON ColorPage EPL-C8200 Revision A Manual Feed sss ttt Insert sss LED: On Line = off, Continue = Blinks LED: On Line = off, Continue = off Description: When “Manual Feed” is enabled by the command or Description: Paper feed cassette indicated by sss is out.
Page 337 EPSON ColorPage EPL-C8200 Revision A the Print Overrun error recurs, however, the data Paper Set sss ttt for that page will be lost and the printer will begin LED: On Line = off, Continue = blinking processing the next page of data.
Page 338 EPSON ColorPage EPL-C8200 Revision A Invalid HDD Write Error ROM A LED: On Line = off, Continue = off LED: On Line = off, Continue = off Description: A fatal problem relating the HDD (Hard Disc Drive) Description: Write was attempted to despite the ROM module in unit has occurred.
Page 339: Warning Message
EPSON ColorPage EPL-C8200 Revision A 5.1.2.3 Warning Message replaced with the value for the Page Size. Depending on the paper sizes, the printer may not be Warning errors have no effect on printer operation. able to detect paper size mismatches.
Page 340 EPSON ColorPage EPL-C8200 Revision A Image Optimum Need Memory LED: No effect on LED state. LED: No effect on LED state. Explanation: There was not enough memory to process the print Explanation: While processing print data, the printer ran out of data and the printer optimized the data (reduced the memory.
Page 341 EPSON ColorPage EPL-C8200 Revision A Format Error ROM A Maintenance Req hhhh LED: No effect on LED state. LED: No effect on LED state. Explanation: If the ROM inserted in the slot A is new, take a Explanation: A warning condition that cannot be corrected by the necessary action.
Page 342 EPSON ColorPage EPL-C8200 Revision A uuuu Toner Low Waste T Box Nearfull LED: No effect on LED state. LED: No effect on LED state. Explanation: The engine has detected (by measuring the dispense Explanation: The Waste Toner Box is almost full. (The engine's...
Page 343: Service-Call Error Messages
EPSON ColorPage EPL-C8200 Revision A 5.1.3 Service-Call Error Messages Table 5-6. Engine Related Service-Call Error Error Type Error Code If the indicated message is “ ”, it means the printer is in a Explanation Refer to: ffff service-call error condition, and all LEDs on the LCD panel light up.
Page 344 EPSON ColorPage EPL-C8200 Revision A Table 5-7. Controller Related Service-Call Error (1/2) Table 5-8. Controller Related Service-Call Error (2/2) Error Error Error Error Explanation Refer to: Explanation Refer to: Type Code Type Code 0017 CPU error (undefined interrupt) FIP-1.47 1021 RAM DIMM error (Slot 1) FIP-1.41...
Page 345: Level 1 Fip (Fault Isolation Procedure)
EPSON ColorPage EPL-C8200 Revision A 5.2 Level 1 FIP (Fault Isolation Procedure) This section describes how to isolate the faulty unit (assembly) by using the Level 1 FIPs. <Preliminary inspection> In each FIP, you are required to perform the “Preliminary inspection” prior to any other actions.
Page 346: Fip-1.1 Y/M/C/K Toner Cartridge Toner Is Out
EPSON ColorPage EPL-C8200 Revision A FIP-1.1 Y/M/C/K TONER CARTRIDGE TONER is Out Finding & Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. Developer Assy, DISPENSE MOTOR ASSY, DEVE.CONTACT ASSY, ADC SENSOR ASSY,...
Page 347: Fip-1.2 Waste Toner Box Is Full
EPSON ColorPage EPL-C8200 Revision A FIP-1.2 WASTE TONER BOX is Full Remedy Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. WASTE TONER SENSOR, WASTE TONER BOX, TONER BOX, MCU PWB Check: Transparency area of the WASTE TONER •...
Page 348: Fip-1.3 Fuser Oil In The Oil Roll Assy Is Out
EPSON ColorPage EPL-C8200 Revision A FIP-1.3 FUSER OIL in the OIL ROLL ASSY is Out Remedy Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. OIL ROLL ASSY, CRU SWITCH ASSY, OIL CAM...
Page 349: Fip-1.4 Paper Out - Cassette 1
EPSON ColorPage EPL-C8200 Revision A FIP-1.4 Paper Out - Cassette 1 Remedy Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. TRAY N/P ACTUATOR, TRAY NO PAPER SENSOR, MCU PWB Isolation: Engine or Controller? Check the Controller PWB.
Page 350: Fip-1.5 Paper Out - Msi Tray
EPSON ColorPage EPL-C8200 Revision A FIP-1.5 Paper Out - MSI Tray Remedy Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. MSI LONG N/P SENSOR, MSI SHORT N/P SENSOR, MCU PWB, MSI N/P ACTUATOR Isolation: Engine or Controller? Check the Controller PWB.
Page 351: Fip-1.6 Drum Cartridge Related Problem
EPSON ColorPage EPL-C8200 Revision A (Continued) FIP-1.5 "Paper Out - MSI Tray" Remedy Check point MSI LONG N/P SENSOR installation Is the MSI N/P ACTUATOR properly functioning depending on the conditions below? • With the diagnostic tool, go to step 7.
Page 352: Fip-1.7 Paper Jam - Exit
EPSON ColorPage EPL-C8200 Revision A FIP-1.7 Paper Jam - Exit Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. MSI LONG N/P SENSOR, MSI SHORT N/P SENSOR, MCU PWB, MSI N/P ACTUATOR Isolation: Engine or Controller? Check the Controller PWB.
Page 353: Fip-1.8 Paper Jam - Regi
EPSON ColorPage EPL-C8200 Revision A FIP-1.8 Paper Jam - REGI. Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. REGI. SENSOR, MAIN P/H ASSY, TURN ROLL ASSY, FEED ROLL, P/H DRIVE ASSY, FEED SOLENOID,...
Page 354: Fip-1.9 Paper Jam - Fuser
EPSON ColorPage EPL-C8200 Revision A FIP-1.9 Paper Jam - FUSER Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. FUSER EXIT ACTUATOR, FUSER EXIT SENSOR, FUSER IN ACTUATOR, FUSER IN SENSOR, FUSER...
Page 355 EPSON ColorPage EPL-C8200 Revision A (Continued) FIP-1.9 "Paper Jam - FUSER" Remedy Step Check point Check: FUSER IN ACTUATOR Is the FUSER IN ACTUATOR functioning properly depending on the conditions below? • With the diagnostic tool, go to step 7.
Page 356: Fip-1.10 Wrong Paper Size
EPSON ColorPage EPL-C8200 Revision A FIP-1.10 Wrong Paper Size Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective Go to Step 2. part(s). SIZE SWITCH ASSY, MAIN P/H ASSY, REGI. SENSOR, TRAY SIZE ACTUATOR, END GUIDE, MCU PWB Isolation: Engine or Controller? Check the Controller PWB.
Page 357: Fip-1.11 Ohp Sheet Is Improperly Set
EPSON ColorPage EPL-C8200 Revision A FIP-1.11 OHP Sheet is Improperly Set Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. FRONT OHP SENSOR, REAR OHP SENSOR, MCU Isolation: Engine or Controller? Check the Controller PWB.
Page 358: Fip-1.12 Paper Exit - Static Jam
EPSON ColorPage EPL-C8200 Revision A FIP-1.12 Paper Exit - Static Jam Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. TOP EXIT SENSOR, MCU PWB Check: TOP EXIT SENSOR for remainder Remove the remaining paper, paper •...
Page 359: Fip-1.14 Paper Static Jam - Fuser
EPSON ColorPage EPL-C8200 Revision A FIP-1.14 PAPER Static Jam - FUSER Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. FUSER EXIT ACTUATOR, FUSER EXIT SENSOR, FUSER IN ACTUATOR, FUSER IN SENSOR, FUSER...
Page 360: Fip-1.15 2Nd Btr Resistance Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.15 2ND BTR Resistance Error Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. 2ND BTR, BTR CAM SOLENOID, MCU PWB Isolation: Engine or Controller? Check the Controller PWB.
Page 361: Fip-1.16 Main Fuser Assy Related Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.16 MAIN FUSER ASSY Related Error Remedy Step Check point Perform the preliminary inspection. Parts to inspect: FUSER ASSY, MCU PWB, FUSER HARNESS ASSY, Replace/reinstall the defective part(s). Go to Step 2. FUSER CONNECTOR, FUSER ASSY, TEMP.
Page 362: Fip-1.17 Oil Roll Assy Is Out
EPSON ColorPage EPL-C8200 Revision A FIP-1.17 OIL ROLL ASSY is Out Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. OIL ROLL ASSY, CRU SWITCH ASSY, FUSER HARNESS ASSY, MAIN HARNESS ASSY, MCU PWB Check: OIL ROLL ASSY installation Go to Step 3.
Page 363: Fip-1.18 Main Fuser Assy Is Out
EPSON ColorPage EPL-C8200 Revision A FIP-1.18 MAIN FUSER ASSY is Out Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. FUSER ASSY, MCU PWB, FUSER HARNESS ASSY, FUSER CONNECTOR Isolation: Engine or Controller? Run the Engine test print or diagnostic test print.
Page 364: Fip-1.19 Drum Cartridge Is Out
EPSON ColorPage EPL-C8200 Revision A FIP-1.19 DRUM CARTRIDGE is Out Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. TONER BOX SENSOR, TONER BOX HARNESS, MAIN HARNESS ASSY, MCU PWB...
Page 365: Fip-1.20 High Resolution Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.20 High Resolution Error Remedy Step Check point Perform the preliminary inspection. Replace/reinstall the defective part(s). Go to Step 2. Parts to inspect: MCU PWB Isolation: Engine or Controller? Check the Controller PWB. Run the Engine test print or diagnostic test print.
Page 366: Fip-1.21 Main Fuser Assy Overheat Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.21 MAIN FUSER ASSY Overheat Error Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. FUSER CONNECTOR, TEMP. SENSOR ASSY, H/R HEATER, P/R HEATER, FUSER ASSY, MAIN HARNESS...
Page 367: Fip-1.22 Ros Assy Related Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.22 ROS ASSY Related Error Remedy Step Check point Perform the preliminary inspection. Replace/reinstall the defective part(s). Go to Step 2. Parts to inspect: ROS ASSY, MCU PWB Isolation: Engine or Controller? Check the Controller PWB.
Page 368: Fip-1.23 Process Motor Assy Related Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.23 PROCESS MOTOR ASSY Related Error Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. PROCESS MOTOR ASSY, PROCESS WDD ASSY, TRANSFER ASSY, TRO SENSOR, MCU PWB Isolation: Engine or Controller? Check the Controller PWB.
Page 369: Fip-1.24 Mcu Pwb Eeprom Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.24 MCU PWB EEPROM Error Remedy Step Check point Perform the preliminary inspection. Replace/reinstall the defective part(s). Go to Step 2. Parts to inspect: COMMUNICATION ASSY, MCU PWB Isolation: Engine or Controller? Check the Controller PWB.
Page 370: Fip-1.25 Cassette 1 Is Out
EPSON ColorPage EPL-C8200 Revision A FIP-1.25 CASSETTE 1 is Out Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. UNIVERSAL CASSETTE, TRAY SIZE ACTUATOR, SIZE SWITCH ASSY, FEEDER PWB, MCU PWB Isolation: Engine or Controller? Check the Controller PWB.
Page 371: Fip-1.26 High Density Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.26 High Density Error Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. DEVE.CONTACT ASSY, ADC SENSOR ASSY, MCU PWB Isolation: Engine or Controller? Run the Engine test print or diagnostic test print.
Page 372: Fip-1.27 Low Density Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.27 Low Density Error Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. DISPENSE MOTOR ASSY, DEVE CONTACT ASSY, Developer Assy, MAIN HARNESS ASSY, MCU PWB Isolation: Engine or Controller? Check the Controller PWB.
Page 373 EPSON ColorPage EPL-C8200 Revision A (Continued) FIP-1.27 "Low Density Error" Remedy Step Check point • With the diagnostic tool, go to step • With the diagnostic tool, go to step 9. Check: ADC Sensor surface • Without the diagnostic tool, go to Is the ADC Sensor surface smeared or lodged with any •...
Page 374: Fip-1.28 P/H Motor Related Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.28 P/H MOTOR Related Error Remedy Step Check point Perform the preliminary inspection. Parts to inspect: P/H MOTOR ASSY, HEAT ROLL, PRESSURE ROLL, Replace/reinstall the defective part(s). Go to Step 2. FUSER ASSY, BELT CLEANER ASSY, EXIT LOWER...
Page 375 EPSON ColorPage EPL-C8200 Revision A (Continued) FIP-1.28 "P/H MOTOR Related Error" Remedy Step Check point Check: EXIT LOWER ASSY Go to Step 9. Replace the interfering part. Rotate the EXIT IDLER GEAR manually. Does the EXIT LOWER ASSY rotate smoothly?
Page 376: Fip-1.29 Environment Sensor Related Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.29 ENVIRONMENT SENSOR Related Error Remedy Step Check point Perform the preliminary inspection. • With the diagnostic tool, go to step 2. Parts to inspect: Replace the defective part. • Without the diagnostic tool, go to ENVIRONMENT SENSOR, P/H HARNESS ASSY, step 3.
Page 377: Fip-1.30 Rotary Motor Assy (Hp Detection) Related Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.30 ROTARY MOTOR ASSY (HP Detection) Related Error Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. ROTARY MOTOR ASSY, ROTARY FRAME ASSY, ROTARY SENSOR ASSY, MCU PWB Isolation: Engine or Controller? Check the Controller PWB.
Page 378: Fip-1.31 Waste Toner Box Is Out
EPSON ColorPage EPL-C8200 Revision A FIP-1.31 WASTE TONER BOX is Out Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. WASTE TONER BOX, DRAM CARTRIDGE, TONER BOX SENSOR, TONER BOX HARNESS, MAIN HARNESS...
Page 379: Fip-1.33 Toner Cartridge Y/M/C/K Is Out
EPSON ColorPage EPL-C8200 Revision A FIP-1.33 TONER CARTRIDGE Y/M/C/K is Out Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. Toner Cartridge, CARTRIDGE SENSOR, MCU PWB Check: Sticker on a Toner Cartridge Go to Step 3.
Page 380: Fip-1.35 Adc Sensor Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.35 ADC SENSOR Error Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. ADC SENSOR ASSY, MAIN HARNESS ASSY, MCU PWB Isolation: Engine or Controller? Check the Controller PWB.
Page 381: Fip-1.36 Periodically Replaced Part - End Of Life
EPSON ColorPage EPL-C8200 Revision A FIP-1.36 Periodically Replaced Part - End Of Life Remedy Step Check point Perform the preliminary inspection. Replace/reinstall the defective part(s). Go to Step 2. Parts to inspect: MCU PWB Check: Error Reset In the Maintenance menu, perform the required counter...
Page 382: Fip-1.37 No Power Is Applied
EPSON ColorPage EPL-C8200 Revision A FIP-1.37 No Power is Applied. Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. P/H HARNESS ASSY, REGI. HARNESS ASSY, MAIN HARNESS ASSY, MCU PWB Check: Controller PWB for power supply voltage 1.
Page 383: Fip-1.38 Abnormal Print Motion
EPSON ColorPage EPL-C8200 Revision A FIP-1.38 Abnormal Print Motion Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. LVPS, HVPS, MCU PWB Does the printer exhibit any print motion at all? Go to Step 4.
Page 384: Fip-1.40 Dimm (Slot P) Related Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.40 DIMM (SLOT P) Related Error Remedy Step Check point Perform the preliminary inspection below: • Remove all optional electrical unit modules to return the printer to the standard condition. Replace/reinstall the defective part(s). Go to Step 2.
Page 385: Fip-1.41 Sd-Ram (Slot S0, S1, S2) Related Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.41 SD-RAM (SLOT S0, S1, S2) Related Error Remedy Step Check point Perform the preliminary inspection below: • Remove all optional electrical unit modules to return the printer to the standard condition. Replace/reinstall the defective part(s).
Page 386: Fip-1.42 Controller Pwb (Ic13, Ic14) Related Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.42 CONTROLLER PWB (IC13, IC14) Related Error Remedy Step Check point Perform the preliminary inspection below: • Remove all electrical unit modules to return the printer to the standard condition. Replace/reinstall the defective part(s). Go to Step 2.
Page 387: Fip-1.44 Dimm (Slot A, B) Related Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.44 DIMM (Slot A, B) Related Error Remedy Step Check point Perform the preliminary inspection below: • Remove all electrical unit modules to return the printer to the standard condition. Replace/reinstall the defective part(s). Go to Step 2.
Page 388: Fip-1.46 Controller Pwb Asic (Ic24, Ic26) Related Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.46 CONTROLLER PWB ASIC (IC24, IC26) Related Error Remedy Step Check point Perform the preliminary inspection below: • Remove all electrical unit modules to return the printer to the standard condition. Replace/reinstall the defective part(s).
Page 389: Fip-1.48 Sram (Ic25) Initialization Error
EPSON ColorPage EPL-C8200 Revision A FIP-1.48 SRAM (IC25) Initialization Error Remedy Step Check point Perform the preliminary inspection below: • Remove all electrical unit modules to return the printer to the standard condition. Replace/reinstall the defective part(s). Go to Step 2.
Page 390: Fip-1.50 "Front Cover Open
EPSON ColorPage EPL-C8200 Revision A FIP-1.50 “FRONT COVER OPEN” Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. FRONT COVER SWITCH R, FRONT COVER SWITCH L, MCU PWB Isolation: Engine or Controller? Run the Engine test print or diagnostic test print.
Page 391: Fip-1.51 "Paper Unit Open
EPSON ColorPage EPL-C8200 Revision A FIP-1.51 “PAPER UNIT OPEN” Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. MAIN P/H ASSY, MAIN HARNESS ASSY, MCU PWB Isolation: Engine or Controller? Run the Engine test print or diagnostic test print.
Page 392: Fip-1.52 "Exit Cover Open
EPSON ColorPage EPL-C8200 Revision A FIP-1.52 “EXIT COVER OPEN” Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. MAIN P/H ASSY, MAIN HARNESS ASSY, MCU PWB Isolation: Engine or Controller? Run the Engine test print or diagnostic test print.
Page 393: Fip-1.53 "Fuser Unit Open
EPSON ColorPage EPL-C8200 Revision A FIP-1.53 “FUSER UNIT OPEN” Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. MAIN FUSER ASSY, MAIN HARNESS ASSY, MCU PWB Isolation: Engine or Controller? Run the Engine test print or diagnostic test print.
Page 394: Fip-1.54 "Paper Out Lc1
EPSON ColorPage EPL-C8200 Revision A FIP-1.54 “PAPER OUT LC1” Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. UNIVERSAL CASSETTE, BOTTOM PLATE ASSY, LOW PAPER SENSOR, FEEDER PWB, MCU PWB Isolation: Engine or Controller? Run the Engine test print or diagnostic test print.
Page 395: Level 2 Fip (Fault Isolation Procedure)
EPSON ColorPage EPL-C8200 Revision A 5.3 Level 2 FIP (Fault Isolation Procedure) This section describes how to isolate the faulty unit (assembly) by using the Level 2 FIPs. <Preliminary inspection> In each FIP, you are required to perform the “Preliminary inspection” prior to any other actions.
Page 396: Fip-2.1 Lvps 5Vdc Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.1 LVPS 5VDC is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. LVPS, MCU PWB, MAIN HARNESS ASSY Check: LVPS Is the voltage level correct at the pins below? - P33-6PIN<=>P33-8PIN: 5VDC...
Page 397: Fip-2.2 Lvps 24Vdc Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.2 LVPS 24VDC is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: LVPS, MCU PWB, MAIN HARNESS ASSY, FUSER ASSY, Replace/reinstall the defective part(s). Go to Step 2. MAIN P/H ASSY, FRONT COVER SWITCH R, P/H...
Page 398 EPSON ColorPage EPL-C8200 Revision A (Continued) FIP-2.2 LVPS is Defective Remedy Step Check point Check: FRONT COVER SWITCH R Close the FRONT COVER ASSY. Replace the FRONT COVER Go to Step 10. Is the voltage level correct at the pins below? SWITCH R.
Page 399 EPSON ColorPage EPL-C8200 Revision A (Continued) FIP-2.2 LVPS is Defective Remedy Step Check point Check: FUSER ASSY electrical continuity Does the FUSER ASSY have proper continuity at the pins Replace the FUSER CONNECTOR. Replace the FUSER ASSY. below? - J71-3PIN<=>J71-4PIN...
Page 400: Fip-2.3 Tray No Paper Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.3 TRAY NO PAPER SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. TRAY NO PAPER SENSOR, REGI. HARNESS ASSY, TRAY N/P HARNESS, MCU PWB...
Page 401: Fip-2.4 Low Paper Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.4 LOW PAPER SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. LOW PAPER SENSOR, TRAY N/P HARNESS, MCU PWB Check: Power supply to LOW PAPER detection signal Is the voltage level correct at the pins below? Go to Step 3.
Page 402: Fip-2.5 Size Switch Assy Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.5 SIZE SWITCH ASSY is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. SIZE SWITCH ASSY, MAIN HARNESS ASSY, MCU PWB Check: Power supply to the SIZE SWITCH ASSY Go to FIP-2.1 "LVPS 5VDC is...
Page 403: Fip-2.6 Feed Solenoid Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.6 FEED SOLENOID is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. FEED SOLENOID, MAIN HARNESS ASSY, MCU PWB Check: Power supply to the FEED SOLENOID Go to FIP-2.2 "LVPS 24VDC is...
Page 404: Fip-2.7 Msi Short N/P Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.7 MSI SHORT N/P SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. MSI SHORT N/P SENSOR, MSI HARNESS ASSY, REGI. HARNESS ASSY, P/H HARNESS ASSY, MCU PWB Check: MSI SHORT N/P detection signal Go to FIP-2.1 "LVPS 5VDC is...
Page 405: Fip-2.8 Msi Long N/P Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.8 MSI LONG N/P SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. MSI LONG N/P SENSOR, MSI HARNESS ASSY, REGI. HARNESS ASSY, P/H HARNESS ASSY, MCU PWB Check: Power supply to the MSI LONG N/P SENSOR Go to FIP-2.1 "LVPS 5VDC is...
Page 406: Fip-2.9 Msi Edge Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.9 MSI EDGE SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. MSI EDGE SENSOR, MSI HARNESS ASSY, REGI. HARNESS ASSY, P/H HARNESS ASSY, MCU PWB Check: Power supply to the MSI EDGE SENSOR Go to FIP-2.1 "LVPS 5VDC is...
Page 407: Fip-2.10 Msi Clutch Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.10 MSI CLUTCH is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. MSI CLUTCH, P/H HARNESS ASSY, REGI. MAIN HARNESS, MSI HARNESS ASSY, MCU PWB Check: Power supply to the MSI CLUTCH Go to FIP-2.2 "LVPS 24VDC is...
Page 408: Fip-2.11 Pick Up Solenoid Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.11 PICK UP SOLENOID is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. PICK UP SOLENOID, P/H HARNESS ASSY, REGI. MAIN HARNESS, MSI HARNESS ASSY, MCU PWB Check: Power supply to the PICK UP SOLENOID Go to FIP-2.2 "LVPS 24VDC is...
Page 409: Fip-2.12 Front Ohp Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.12 FRONT OHP SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to check: Replace/reinstall the defective part(s). Go to Step 2. FRONT OHP SENSOR, REGI. HARNESS ASSY, P/H HARNESS ASSY, MCU PWB Check: Power supply to the FRONT OHP SENSOR Go to FIP-2.1 "LVPS 5VDC is...
Page 410: Fip-2.13 Rear Ohp Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.13 REAR OHP SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. REAR OHP SENSOR, REGI. HARNESS ASSY, P/H HARNESS ASSY, MCU PWB Check: Power supply to the REAR OHP SENSOR Go to FIP-2.1 "LVPS 5VDC is...
Page 411: Fip-2.14 Regi. Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.14 REGI. SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. REGI.SENSOR, REGI. HARNESS ASSY, P/H HARNESS ASSY, MCU PWB Check: Power supply to the REGI. SENSOR Go to FIP-2.1 "LVPS 5VDC is...
Page 412: Fip-2.15 Regi. Clutch Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.15 REGI. CLUTCH is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. REGI. CLUTCH, P/H HARNESS ASSY, REGI. HARNESS ASSY, MCU PWB Check: Power supply to the REGI. CLUTCH Go to FIP-2.1 "LVPS 5VDC is...
Page 413: Fip-2.16 Pre-Regi. Clutch Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.16 PRE-REGI. CLUTCH is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. REGI. CLUTCH, P/H HARNESS ASSY, REGI. HARNESS ASSY, MCU PWB Check: Power supply to the REGI. CLUTCH Go to FIP-2.2 "LVPS 24VDC is...
Page 414: Fip-2.17 Waste Toner Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.17 WASTE TONER SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: WASTE TONER SENSOR, WASTE TONER BOX, Replace/reinstall the defective part(s). Go to Step 2. TONER BOX HARNESS, MAIN HARNESS ASSY, MCU Check: Power supply to the WASTE TONER SENSOR Go to FIP-2.1 "LVPS 5VDC is...
Page 415: Fip-2.18 Toner Box Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.18 TONER BOX SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. TONER BOX SENSOR, TONER BOX HARNESS, MAIN HARNESS ASSY, MCU PWB Check: Power supply to the TONER BOX SENSOR Go to FIP-2.1 "LVPS 5VDC is...
Page 416: Fip-2.19 Ros Assy Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.19 ROS ASSY is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: ROS ASSY, MAIN HARNESS ASSY, EXIT HARNESS, Replace/reinstall the defective part(s). Go to Step 2. TOP EXIT SENSOR, FRONT COVER SWITCH R, MAIN...
Page 417 EPSON ColorPage EPL-C8200 Revision A FIP-2.19 "ROS ASSY is Defective" (Continued) Remedy Step Check point Check: MAIN HARNESS ASSY continuity Does the MAIN HARNESS ASSY have proper continuity at the pins below? - J33-2PIN<=>P195-2PIN Go to Step 10. Replace the MAIN HARNESS ASSY.
Page 418: Fip-2.20 Adc Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.20 ADC SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. ADC SENSOR ASSY, MAIN HARNESS ASSY, MCU PWB Check: Power supply to the ADC Sensor Go to FIP-2.1 "LVPS 5VDC is...
Page 419: Fip-2.22 Cartridge Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.22 CARTRIDGE SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. CARTRIDGE, FUSER CONNECTOR, FUSER HARNESS ASSY, MCU PWB Check: Power supply to the CARTRIDGE SENSOR Go to FIP-2.1 "LVPS 5VDC is...
Page 420: Fip-2.23 Used Cart. Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.23 USED CART. SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. USED CART. SENSOR, MAIN HARNESS ASSY, MCU Check: Power supply to the USED CART. SENSOR Go to FIP-2.1 "LVPS 5VDC is...
Page 421: Fip-2.24 Rotary Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.24 ROTARY SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. ROTARY SENSOR, MAIN HARNESS ASSY, MCU PWB Check: Power supply to the ROTARY SENSOR. SENSOR Go to FIP-2.1 "LVPS 5VDC is...
Page 422: Fip-2.25 Tro Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.25 TRO SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. TRO SENSOR, MAIN HARNESS ASSY, MCU PWB Check: Power supply to the TRO SENSOR Go to FIP-2.1 "LVPS 5VDC is...
Page 423: Fip-2.26 Btr Cam Solenoid Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.26 BTR CAM SOLENOID is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. BTR CAM SOLENOID, MAIN HARNESS ASSY, MCU Check: Power supply to the BTR CAM SOLENOID Go to FIP-2.2 "LVPS 24VDC is...
Page 424: Fip-2.27 Fuser In Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.27 FUSER IN SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. FUSER IN SENSOR, MAIN HARNESS ASSY, FUSER HARNESS ASSY, FUSER IN HARNESS, MCU PWB Check: Power supply to the FUSER IN SENSOR Go to FIP-2.1 "LVPS 5VDC is...
Page 425: Fip-2.28 Fuser Exit Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.28 FUSER EXIT SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. FUSER EXIT SENSOR, MAIN HARNESS ASSY, FUSER HARNESS ASSY, MCU PWB Check: Power supply to the FUSER EXIT SENSOR Go to FIP-2.1 "LVPS 5VDC is...
Page 426: Fip-2.29 Temp. Sensor Assembly Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.29 TEMP. SENSOR ASSEMBLY is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. TEMP. SENSOR ASSY, MAIN HARNESS ASSY, FUSER HARNESS ASSY, MCU PWB Check: Thermistor in the TEMP.
Page 427: Fip-2.30 Oil Cam Solenoid Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.30 OIL CAM SOLENOID is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. OIL CAM SOLENOID, FUSER HARNESS ASSY, MAIN HARNESS ASSY, MCU PWB Check: Power supply to the OIL CAM SOLENOID Go to FIP-2.2 "LVPS 24VDC is...
Page 428: Fip-2.31 Cleaner Cam Solenoid Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.31 CLEANER CAM SOLENOID is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. CLEANER CAM SOLENOID, FUSER HARNESS ASSY, MAIN HARNESS ASSY, MCU PWB...
Page 429: Fip-2.32 Top Exit Sensor Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.32 TOP EXIT SENSOR is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. TOP EXIT SENSOR, MAIN HARNESS ASSY, EXIT HARNESS, MCU PWB Check: Power supply to the TOP EXIT SENSOR Go to FIP-2.1 "LVPS 5VDC is...
Page 430: Fip-2.33 Process Motor Assy Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.33 PROCESS MOTOR ASSY is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. PROCESS MOTOR ASSY, MAIN HARNESS ASSY, MCU Check: Power supply to the PROCESS MOTOR ASSY Is the voltage level correct at the pins below? Go to Step 4.
Page 431: Fip-2.34 P/H Motor Assy Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.34 P/H MOTOR ASSY is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. P/H MOTOR ASSY, MAIN HARNESS ASSY, MCU PWB Check: Power supply to the P/H MOTOR ASSY Is the voltage level correct at the pins below? Go to Step 4.
Page 432: Fip-2.35 Rotary Motor Assy Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.35 ROTARY MOTOR ASSY is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. ROTARY MOTOR ASSY, MAIN HARNESS ASSY, MCU Check: Power supply to the ROTARY MOTOR ASSY Is the voltage level correct at the pins below? Go to Step 4.
Page 433: Fip-2.36 Dispense Motor Assy Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.36 DISPENSE MOTOR ASSY is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. DISPENSE MOTOR ASSY, MAIN HARNESS ASSY, MCU Check: Power supply to the DISPENSE MOTOR ASSY Go to FIP-2.2 "LVPS 24VDC is...
Page 434: Fip-2.37 Deve. Clutch Assy Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.37 DEVE. CLUTCH ASSY is Defective. Remedy Step Check point Perform the preliminary inspection. Parts to inspect: Replace/reinstall the defective part(s). Go to Step 2. DEVE. CLUTCH ASSY, MAIN HARNESS ASSY, MCU Check: Power supply to the DEVE. CLUTCH ASSY Go to FIP-2.2 "LVPS 24VDC is...
Page 435: Fip-2.38 Hvps Is Defective
EPSON ColorPage EPL-C8200 Revision A FIP-2.38 HVPS is Defective Remedy Step Check point Perform the preliminary inspection. Parts to inspect: BCR WIRE, DEVE. WIRE, BCR CONNECTOR ASSY, Replace/reinstall the defective part(s). Go to Step 2. DEVE. CONTACT ASSY, DTS WIRE, DTS PLATE, 2ND...
Page 436 EPSON ColorPage EPL-C8200 Revision A (Continued) FIP-2.38 "HVPS is Defective" Remedy Step Check point Check: Power supply to the HVPS Is the voltage level correct at the pins below? Go to Step 12. Go to Step 11. - P/J41-1<=>P/J41-3: 24VDC Check: Power supply to the LVPS Go to FIP-2.2 "LVPS 24VDC is...
Page 437: Fip-2.39 Electrical Noise
EPSON ColorPage EPL-C8200 Revision A FIP-2.39 Electrical Noise Remedy Step Check point Perform the preliminary inspection. Parts to inspect: LVPS, BCR CONNECTOR ASSY, DEVE. CONTACT Replace/reinstall the defective part(s). Go to Step 2. ASSY, 2ND BTR ASSY, H/R HEATER, P/R HEATER,...
Page 438: Print Quality Troubleshooting
EPSON ColorPage EPL-C8200 Revision A 5.4 Print Quality Troubleshooting 5.4.1 Print Quality Troubleshooting Entry Chart This section describes how to solve the print quality problems by using the Level 3 FIPs. <Preliminary inspection> In each FIP, you are required to perform the “Preliminary inspection”...
Page 439: Print Quality Fip
EPSON ColorPage EPL-C8200 Revision A 5.4.2 Print Quality FIP The FIPs for the common problems are as listed below: NOTE: The Print Quality FIP is applicable on the condition that the 1. "Low image density" printer controller (Controller PWB) is functioning properly. To 2.
Page 440: Low Image Density
EPSON ColorPage EPL-C8200 Revision A 1. Low image density Phenomenon: Overall Image density is lower than normally. Perform the preliminary inspection. Parts to inspect: Toner Cartridge, DRUM CARTRIDGE, HVPS, ROS ASSY, MCU PWB Item Check Points Remedy (When abnormal) Toner Cartridge for its toner level Replace the Toner Cartridge.
Page 441: Blank Prints
EPSON ColorPage EPL-C8200 Revision A 2. Blank prints Phenomenon: The entire print is blank. Perform the preliminary inspection. Parts to inspect: DRUM CARTRIDGE, Toner Cartridge, HVPS, ROS ASSY, MCU PWB Item Check Points Remedy (When abnormal) Toner Cartridge for its toner level Replace the Toner Cartridge.
Page 442: Black Prints
EPSON ColorPage EPL-C8200 Revision A 3. Black prints Phenomenon: Entire page is completely black. Perform the preliminary inspection. Parts to inspect: DRUM CARTRIDGE, HVPS, ROS ASSY, MCU PWB Item Check Points Remedy (When abnormal) Improper charging Using a sheet of paper, cover the laser beam Refer to “FIP-2.38 "HVPS is Defective".
Page 443: White/Light Deletion Along The Paper Feed Direction
EPSON ColorPage EPL-C8200 Revision A 4. White/light deletion along the Paper Feed Direction Phenomenon: White/light bands run along the direction of paper feeding. Paper Feeding Direction Perform the preliminary inspection. Parts to inspect: DRUM CARTRIDGE, HVPS, ROS ASSY, MCU PWB, FUSER ASSY, MAIN FUSER ASSY...
Page 444: White/Shady Deletion Lines Appear Vertically
EPSON ColorPage EPL-C8200 Revision A 5. White/Shady deletion lines appear vertically to the paper feeding direction Phenomenon: White/light deletion lines run vertically to the paper feeding direction. Paper Feeding Direction Perform the preliminary inspection. Parts to inspect: Developer ASSY, DRUM CARTRIDGE, BELT TRANSFER ASSY, 2ND BTR, HEAT ROLL, PRESSURE...
Page 445: Black/Color Spots
EPSON ColorPage EPL-C8200 Revision A 6. Black/Color Spots Phenomenon: Black/Color spots appear in the output. Perform the preliminary inspection. Parts to inspect: DRUM CARTRIDGE, HVPS, 2ND BTR ASSY, FUSER ASSY, (HEAT ROLL/PRESSURE ROLL) Item Check Points Remedy (When abnormal) Damp paper Replace the paper.
Page 446: Toner Smearing
EPSON ColorPage EPL-C8200 Revision A 7. Toner Smearing Phenomenon: Non-printed area on the paper is smeared with toner. Perform the preliminary inspection. Parts to inspect: DRUM CARTRIDGE, HVPS, Developer ASSY, DEVE. CONTACT ASSY Item Check Points Remedy (When abnormal) Deteriorated carrier Replace the relevant Developer assy with a new Replace the Developer assy.
Page 447: Skew
EPSON ColorPage EPL-C8200 Revision A 8. Skew Phenomenon: The printed image is skewed. Perform the preliminary inspection. Parts to inspect: MAIN FUSER ASSY, PICK UP ROLL, FEED ROLL ASSY, TURN ROLL ASSY, MAIN P/H ASSY Item Check Points Remedy (When abnormal) Set paper or paper cassette properly.
Page 448: Creased Paper
EPSON ColorPage EPL-C8200 Revision A 9. Creased paper Phenomenon: The image is printed on a creased paper. Perform the preliminary inspection. Parts to inspect: MAIN FUSER ASSY, HEAT ROLL, PRESSURE ROLL, MCU PWB, DRUM CARTRIDGE, RETARD PAD ASSY, TURN ROLL ASSY, FEED ROLL ASSY, Paper cassettes...
Page 449: Improper Fusing
EPSON ColorPage EPL-C8200 Revision A 10. Improper fusing Phenomenon: Output image is easily rubbed off the paper. Perform the preliminary inspection. Parts to inspect: TEMP. SENSOR ASSY, MAIN FUSER ASSY, HEAT ROLL, PRESSURE ROLL, MCU PWB Item Check Points Remedy (When abnormal) Damp paper Replace the Paper.
Page 450 MAINTENANCE...
Page 451 Table of Contents About On-Site Servicing ............... 1 On-site Service Flow ................. 2 Description of the On-site Service ............ 3 Maintenance Menu ................5 Entry to the Maintenance Menu ............5 Engine Status Sheet ................. 6 Consumable Replacement..............9 TONER CARTRIDGE Replacement ..........10 OIL ROLL ASSEMBLY Replacement ..........
Page 452: About On-Site Servicing
EPSON ColorPage EPL-C8200 Revision A 6.1 About On-Site Servicing - Do not catch your hands and clothes in the rotating parts such as rollers and fans. This section contains information you need when visiting your customer for on-site servicing including preventive maintenance required to...
Page 453: On-Site Service Flow
EPSON ColorPage EPL-C8200 Revision A 6.1.1 On-site Service Flow Figure 6-1. On-site Service Flowchart Chapter 6 Maintenance...
Page 454: Description Of The On-Site Service
EPSON ColorPage EPL-C8200 Revision A 6.1.2 Description of the On-site Service 2. If any abnormality is found in the listed check points: Check the life counters of the consumables and regularly This section gives instruction on the on-site service in detail.
Page 455 EPSON ColorPage EPL-C8200 Revision A Preventive maintenance (Checking the consumables and regularly Final checkout replaced parts) 1. Check exterior view of the printer. In addition to repair and maintenance of the printer, preventive 2. If necessary, give an instruction to the users.
Page 456: Maintenance Menu
EPSON ColorPage EPL-C8200 Revision A 6.2 Maintenance Menu 2. Referring to the flowchart below, activate the desirable function through the panel operation. Maintenance Menu contains the following functions: NOTE: Shows life counter values for consumables and regularly replaced 1. Consumable and regularly replaced items for the EPL-C8200 can parts and total number of printed pages and color print pages be also used with the EPL-C8000.
Page 457: Engine Status Sheet
EPSON ColorPage EPL-C8200 Revision A 6.2.2 Engine Status Sheet Figure 6-3 shows an Engine Status Sheet sample. Total Counts Shows the same value as for Total Pages in the Total sheets Engine Status Sheet Setup Menu. Sheets are counted regardless of the sizes.
Page 458 EPSON ColorPage EPL-C8200 Revision A Fuser Indicates the version of the P-ROM on the MCU PWB. (Example: Version3.01.47 = 30147) Fuser Oil Shows a consumption condition of the Fuser oil. The indicated counter value is the same as for the...
Page 459 EPSON ColorPage EPL-C8200 Revision A Table 6-1. Engine Status Sheet Information Details Kept by: Counter limit Information Count unit When to count Conditions for clearing the counter Where to store Total Sheets Engine ~ 99,999,999 Sheets Printing Maintenance Menu>Total Counter Clear...
Page 460: Consumable Replacement
EPSON ColorPage EPL-C8200 Revision A 6.3 Consumable Replacement This printer allows the users to replace the cunsumables. The consumables includes the following 4 items: b) OIL ROLL ASSEMBLY a) TONER CARTRIDGE d) WASTE TONER BOX c) DRUM CARTRIDGE Figure 6-4. Consumables...
Page 461: Toner Cartridge Replacement
EPSON ColorPage EPL-C8200 Revision A 6.3.1 TONER CARTRIDGE Replacement 3. If you can see the color that you need to replace at the installation window, go to Step 4. If you the cartridge to be replaced is not in the...
Page 462 EPSON ColorPage EPL-C8200 Revision A Figure 6-10. TONER CARTRIDGE Replacement 5 Figure 6-8. TONER CARTRIDGE Replacement 3 5. Hold a new TONER CARTRIDGE by the right and left ends and gently shake it up and down to distribute toner evenly.
Page 463: Oil Roll Assembly Replacement
EPSON ColorPage EPL-C8200 Revision A 6.3.2 OIL ROLL ASSEMBLY Replacement 3. Remove the cover from a new OIL ROLL ASSEMBLY. 4. Remove 2 shipping pins from both sides of the OIL ROLL OIL ROLL ASSEMBLY is equipped to fix toner image exactly on a ASSEMBLY.
Page 464: Drum Cartridge Replacement
EPSON ColorPage EPL-C8200 Revision A 6.3.3 DRUM CARTRIDGE Replacement 1. Turn the printer power on. 2. Open the FRONT COVER. The photoconductor of the DRUM CARTRIDGE is exposed by the ROS ASSEMBLY and developed by the DEVELOPER ASSEMBLY, and transmits images onto the IBT.
Page 465 EPSON ColorPage EPL-C8200 Revision A NOTE:Ensure that the photo conductor (a blue cyrindrical part) is 5. Hold the handle in the DRUM CARTRIDGE and draw the DRAM CARTRIDGE out half way. not in contact with any parts inside the printer during its installation.
Page 466 EPSON ColorPage EPL-C8200 Revision A 10. Turn the TENSION LEVER in the direction indicated with the arrow to align it with the symbol. Figure 6-21. DRUM CARTRIDGE Replacement 6 11. Close the FRONT COVER. Chapter 6 Maintenance 6-15...
Page 467: Waste Toner Box Replacement
EPSON ColorPage EPL-C8200 Revision A 6.3.4 WASTE TONER BOX Replacement 3. Pull the WASTE TONER BOX straight out. WASTE TONER BOX is used to collect toner that was not used for printing. It is not necessary to change the WASTE TONER BOX when the DRUM CARTRIDGE is also replaced, because a consumable DRUM CARTRIDGE contains a WASTE TONER BOX.
Page 468: Regularly Replaced Parts Replacement
EPSON ColorPage EPL-C8200 Revision A 6.4 Regularly Replaced Parts Replacement 6.5 Installation Table below list the regularly replaced parts and the corresponding This section describes provides a guideline for installing the printer on reference sections. its place. Power If you have replaced any of the regularly replaced parts, perform the relevant counter reset in the Maintenance Menu.
Page 469 EPSON ColorPage EPL-C8200 Revision A Location Installation Procedure To operate properly, a certain amount of space around the The following describes the installation procedures. For details, see printer is required. (For details, see Chapter 1/Section 1.2.4.) the User’s Guide. The printer is located in an area where the temperature and The printer weighs about 69 kg.
Page 470 EPSON ColorPage EPL-C8200 Revision A 9) Remove a total of 4 spacers from where the toner cartridges are 17) Install the OIL ROLL ASSEMBLY above the FUSER inserted. ASSEMBLY. 10) Unpack the TONER CARTRIDGEs. Hold both ends of each 18) Close the FUSER ASSEMBLY.
Page 471 APPENDIX...
Page 472 Table of Contents Parts List ....................1 Parts List (Large Capacity Paper Unit) ........71 Exploded Diagrams (Large Capacity Paper Unit) ..... 73 How to Use the Parts List ..............1 Wiring Diagrams (Large Capacity Paper Unit) ......75 Parts List Tables ................2 500-Sheet Paper Cassette Unit ............
Page 473: Parts List
EPSON ColorPage EPL-C8200 Revision A A.1 Parts List A.1.1 How to Use the Parts List Followings are the points to note when using the part list and exploded This chapter describes the printer parts. The parts are grouped into 14 diagrams.
Page 474 EPSON ColorPage EPL-C8200 Revision A A.1.2 Parts List Tables Table A-2. Parts List (2/9) Table A-1. Parts List (1/9) PL No. Part Name Reference PL No. Part Name Reference PL 3.1.7 FEED GEAR 3.2.6.4/5 PL 1.1.1 FRONT COVER ASSY 3.2.4.1 PL 3.1.8...
Page 475 EPSON ColorPage EPL-C8200 Revision A Table A-3. Parts List (3/9) Table A-4. Parts List (4/9) PL No. Part Name Reference PL No. Part Name Reference PL 4.2.11 PICK UP ROLL 3.2.7.8 PL 4.3.16 SENSOR 3.2.7.14 PL 4.2.15 BEARING 3.2.7.12 PL 5.1.1 MAIN P/H ASSY (With 2-20) 3.2.8.1...
Page 476 EPSON ColorPage EPL-C8200 Revision A Table A-5. Parts List (5/9) Table A-6. Parts List (6/9) PL No. Part Name Reference PL No. Part Name Reference PL 5.2.25 REGI. LOWER BEARING 3.2.8.10 PL 7.2.4 ROTARY REAR BEARING 3.2.10.5 PL 5.2.26 REGI. FRONT SPRING 3.2.8.10...
Page 477 EPSON ColorPage EPL-C8200 Revision A Table A-7. Parts List (7/9) Table A-8. Parts List (8/9) PL No. Part Name Reference PL No. Part Name Reference PL 9.2.10 BEARING 3.2.12.14/17/ PL 9.4.4 SENSOR 18/20 PL 9.4.5 FUSER IN HARNESS PL 9.2.12 HEAT ROLL 3.2.12.10...
Page 478: Exploded Diagrams
EPSON ColorPage EPL-C8200 Revision A A.1.3 Exploded Diagrams Table A-9. Parts List (9/9) PL No. Part Name Reference PL 11.1.20 ROTARY MOTOR ASSY 3.2.14.4 PL 11.1.21 ROTARY MOTOR PWB 3.2.14.3 PL 11.1.22 DISPENSE MOTOR ASSY 3.2.14.5 PL 11.1.23 DEVE. CLUTCH ASSY 3.2.14.9...
Page 479 EPSON ColorPage EPL-C8200 Revision A Figure A-2. PL2.1 Paper Tray I Figure A-3. PL2.2 Paper Tray II Chapter A Appendix...
Page 480 EPSON ColorPage EPL-C8200 Revision A Figure A-4. PL3.1 Paper Feeder Figure A-5. PL4.1 Multi Sheet Insert I Chapter A Appendix...
Page 481 EPSON ColorPage EPL-C8200 Revision A Figure A-6. PL4.2 Multi Sheet Insert II Figure A-7. PL4.3 Multi Sheet Insert III Chapter A Appendix...
Page 482 EPSON ColorPage EPL-C8200 Revision A Figure A-9. PL5.2 Paper Transportation II Figure A-8. PL5.1 Paper Transportation I Chapter A Appendix A-10...
Page 483 EPSON ColorPage EPL-C8200 Revision A Figure A-11. PL7.1 Development I Figure A-10. PL6.1 Xerographics Chapter A Appendix A-11...
Page 484 EPSON ColorPage EPL-C8200 Revision A Figure A-13. PL8.1 IBT I Figure A-12. PL7.2 Development II Chapter A Appendix A-12...
Page 485 EPSON ColorPage EPL-C8200 Revision A Figure A-15. PL8.3 IBT III Figure A-14. PL8.2 IBT II Chapter A Appendix A-13...
Page 486 EPSON ColorPage EPL-C8200 Revision A Figure A-17. PL9.1 Fusing I Figure A-16. PL8.4 IBT IV Chapter A Appendix A-14...
Page 487 EPSON ColorPage EPL-C8200 Revision A Figure A-18. PL9.2 Fusing II Figure A-19. PL9.3 Fusing III Chapter A Appendix A-15...
Page 488 EPSON ColorPage EPL-C8200 Revision A Figure A-21. PL10.1 Paper Exit I Figure A-20. PL9.4 Fusing IV Chapter A Appendix A-16...
Page 489 EPSON ColorPage EPL-C8200 Revision A Figure A-23. PL11.1 Drive Figure A-22. PL10.2 Paper Exit II Chapter A Appendix A-17...
Page 490 EPSON ColorPage EPL-C8200 Revision A Figure A-24. PL12.1 Frame Figure A-25. PL 13.1 Electrical I Chapter A Appendix A-18...
Page 491 EPSON ColorPage EPL-C8200 Revision A Figure A-26. PL13.2 Electrical II Figure A-27. PL14.1 Controller Chapter A Appendix A-19...
Page 492: Wiring Diagrams
EPSON ColorPage EPL-C8200 Revision A A.2 Wiring Diagrams A.2.1 P/J Locations This section describes the connector locations. "P" and "J" stand for "Plug" and "Jack", respectively. Figure A-28. P/J Location (1) Chapter A Appendix A-20...
Page 493 EPSON ColorPage EPL-C8200 Revision A Figure A-30. P/J Location (3) Figure A-29. P/J Location (2) Chapter A Appendix A-21...
Page 494 EPSON ColorPage EPL-C8200 Revision A Figure A-31. P/J Location (4) Figure A-32. P/J Location (5) Chapter A Appendix A-22...
Page 495 EPSON ColorPage EPL-C8200 Revision A Figure A-34. P/J Location (7) Figure A-33. P/J Location (6) Chapter A Appendix A-23...
Page 496: P/J Locations
EPSON ColorPage EPL-C8200 Revision A A.2.2 Plug and Jack (P/J) Location Table The following lists the coordinates of the connectors (P/J) described in 1.1 P/J Locations. ( Table A-10. Plug and Jack (P/J) Location Table (1/7) Coordinate Notes E-205 Connects MCU PWB and Controller PWB.
Page 497 EPSON ColorPage EPL-C8200 Revision A Table A-11. Plug and Jack (P/J) Location Table (2/7) Table A-12. Plug and Jack (P/J) Location Table (3/7) Coordinate Notes Coordinate Notes Connects Process Motor Assembly and Main Harness F-813 Connector in Fuser Harness Assembly.
Page 498 EPSON ColorPage EPL-C8200 Revision A Table A-13. Plug and Jack (P/J) Location Table (4/7) Table A-14. Plug and Jack (P/J) Location Table (5/7) Coordinate Notes Coordinate Notes Registration Harness Assembly and P/H Harness E-211 Connects Low Paper Sensor and P/H Harness Assembly.
Page 499 EPSON ColorPage EPL-C8200 Revision A Table A-15. Plug and Jack (P/J) Location Table (6/7) Table A-16. Plug and Jack (P/J) Location Table (7/7) Coordinate Notes Coordinate Notes 163A G-707 Connects Main Harness Assembly and Exit Connector-4P. F-608 Connects Rotary Motor PWB and Main Harness Assembly.
Page 500: Wiring Diagrams And Signal Lnformation
EPSON ColorPage EPL-C8200 Revision A A.3 Wiring Diagrams and Signal lnformation NOTE: On the following pages, the Developer Assembly Y, Developer Assembly M, Developer Assembly C, Developer Assembly Bk are called the Developer Assembly. A.3.1 Master Wiring Diagram The following table gives the notations used in the wiring diagrams on the next page.
Page 501 EPSON ColorPage EPL-C8200 Revision A Figure 1-36. Master Wiring Diagram Chapter A Appendix A-29...
Page 502: Wiring And Signal Description Between Components
EPSON ColorPage EPL-C8200 Revision A A.3.2 Wiring and Signal Description Between Components A.3.2.1 Organization § 3. MCU PWB, HVPS, LVPS, BCR Connector Assembly, Developer Contact Assembly, Transfer Assembly, 2nd BTR Cam Assembly, Drum Cartridge, The wiring diagram is divided into the following 13 sections. The signal...
Page 503 EPSON ColorPage EPL-C8200 Revision A §6 . MCU PWB, LVPS, BTR Cam Solenoid, TRO Sensor, P/H Motor § 12. MCU PWB, Top Exit Sensor, Exit Chute Switch, Full Stack Sensor, Assembly, Process Motor Assembly Fuser Fan Connection between: • MCU PWB and BTR Cam Solenoid Connection between: •...
Page 504: Notations On The Diagrams For The Wiring And Signal Descriptions Between Components
EPSON ColorPage EPL-C8200 Revision A A.3.3 Notations on the Diagrams for the Wiring and Table A-19. Notations in Use (2/2) Signal Descriptions between Components The following table gives the notations used in the wiring diagrams on the following pages. NOTE: Standard and common symbols are not described.
Page 505: Wiring Diagram - §1
EPSON ColorPage EPL-C8200 Revision A A.3.3.1 Wiring Diagram - §1 LVPS overcurrent protection circuit If the power voltage (24VDC/5VDC) is shorted, all power is turned off. After the shorted state is canceled, the system recovers by Table A-20. Signal Description - §1...
Page 506 EPSON ColorPage EPL-C8200 Revision A Figure 1-37. Wiring Diagram - §1 Chapter A Appendix A-34...
Page 507: Wiring Diagram - §2
EPSON ColorPage EPL-C8200 Revision A A.3.3.2 Wiring Diagram - §2 Table A-21. Signal Description - §2 Signal Name Description LED ON (L) 5VDC Control signal to turn the LED ON/OFF in the ADC Sensor (ADC Sensor Assembly). ADC SIG Measurement signal from the ADC Sensor (ADC Sensor Assembly).
Page 508 EPSON ColorPage EPL-C8200 Revision A Figure 1-38. Wiring Diagram - §2 Chapter A Appendix A-36...
Page 509: Wiring Diagram - §3
EPSON ColorPage EPL-C8200 Revision A A.3.3.3 Wiring Diagram - §3 Table A-22. Wiring Diagram - §3 Signal Name Description DTS CONT Output control signal for the DTS output. (Analog) DTS ON (L) 24VDC Control signal to turn the DTS output ON/OFF.
Page 510 EPSON ColorPage EPL-C8200 Revision A Figure 1-39. Wiring Diagram - §3 Chapter A Appendix A-38...
Page 511: Wiring Diagram - §4
EPSON ColorPage EPL-C8200 Revision A A.3.3.4 Wiring Diagram - §4 Table A-23. Signal Description - §4 Signal Name Description USED CARTRIDGE Signal to detect new/old Toner cartridge (Low: New/ SENSED (H) 5VDC High: Old). SENSOR ON (H) 5VDC Sensor power ON/OFF signal for the Used Cartridge Sensor and Cartridge Sensor (High: ON/Low: OFF).
Page 512 EPSON ColorPage EPL-C8200 Revision A Figure 1-40. Wiring Diagram - §4 Chapter A Appendix A-40...
Page 513: Wiring Diagram - §5
EPSON ColorPage EPL-C8200 Revision A A.3.3.5 Wiring Diagram - §5 Rotation/Hold by the signals See the table below: Table A-24. Wiring Diagram - §5 Table A-26. Rotation/Hold by the signals Signal Name Description ROTARY Rotary Motor MOTOR ON (L) Hold (L)
Page 514 EPSON ColorPage EPL-C8200 Revision A Figure 1-41. Wiring Diagram - §5 Chapter A Appendix A-42...
Page 515: Wiring Diagram - §6
EPSON ColorPage EPL-C8200 Revision A A.3.3.6 Wiring Diagram - §6 Process Motor Assembly Motor type: Permanent magnet field DC servo motor Table A-27. Wiring Diagram - §6 Number of polarities: 3-phase/12 polarities Signal Name Description BTR CAM SOLENOID ON (L) Control signal to turn the BTR Cam Solenoid ON/ Number of rotations (motor controlled): 1735.358rpm ±0.5%...
Page 516 EPSON ColorPage EPL-C8200 Revision A Figure 1-42. Wiring Diagram - §6 Chapter A Appendix A-44...
Page 517: Wiring Diagram - §7
EPSON ColorPage EPL-C8200 Revision A A.3.3.7 Wiring Diagram - §7 Table A-28. Wiring Diagram - §7 Signal Name Description AC N Neutral signal in the AC input from the power supply (Heater power supply voltage). AC L Line signal in the AC input from the power supply (Heater power supply voltage).
Page 518 EPSON ColorPage EPL-C8200 Revision A Figure 1-43. Wiring Diagram - §7 Chapter A Appendix A-46...
Page 519: Wiring Diagram - §8
EPSON ColorPage EPL-C8200 Revision A A.3.3.8 Wiring Diagram - §8 Table A-29. Wiring Diagram - §8 Signal Name Description OIL CAM SOLENOID ON (L) Control signal to turn the Oil Cam Solenoid ON/ 24VDC OFF. EXCHANGE SOLENOID PUSH Control signal to turn ON/OFF the Exchange ON ( L) 24VDC Solenoid in the push direction (Face-Up ejection).
Page 520 EPSON ColorPage EPL-C8200 Revision A Figure 1-44. Wiring Diagram - §8 Chapter A Appendix A-48...
Page 521: Wiring Diagram - §9
EPSON ColorPage EPL-C8200 Revision A A.3.3.9 Wiring Diagram - §9 Table A-31. Size Switch Signal Table A-30. Wiring Diagram - §9 Paper Size Switch Voltage Paper size (Unit: V DC) Signal Name Description No paper tray 0.275~0.293 [1] SIZE SWITCH Signal to detect the size of the paper in Tray 1.
Page 522 EPSON ColorPage EPL-C8200 Revision A Figure 1-45. Wiring Diagram - §9 Chapter A Appendix A-50...
Page 523: Wiring Diagram - §10
EPSON ColorPage EPL-C8200 Revision A A.3.3.10 Wiring Diagram - §10 Table A-32. Wiring Diagram - §10 Signal Name Description REGISTRATION PAPER Signal from the Registration Sensor to detect the SENSED (L) 5VDC paper on the Main P/H Assembly. FRONT OHP WHITE SENSED...
Page 524 EPSON ColorPage EPL-C8200 Revision A Figure 1-46. Wiring Diagram - §10 Chapter A Appendix A-52...
Page 525: Wiring Diagram - §11
EPSON ColorPage EPL-C8200 Revision A A.3.3.11 Wiring Diagram - §11 Table A-33. Wiring Diagram - §11 Signal Name Description MSI EDGE PAPER SENSED Signal from the MSI Edge Sensor to detect the (L) 5VDC paper in the MSI paper feeder. (High: No paper/ Low: Paper in the feeder) •...
Page 526 EPSON ColorPage EPL-C8200 Revision A Figure 1-47. Wiring Diagram - §11 Chapter A Appendix A-54...
Page 527: Wiring Diagram - §12
EPSON ColorPage EPL-C8200 Revision A A.3.3.12 Wiring Diagram - §12 Table A-34. Wiring Diagram - §12 Signal Name Description TOP EXIT PAPER SENSED (L) Signal from the Top Exit Sensor to detect the paper 5VDC on the Exit Lower Assembly.
Page 528 EPSON ColorPage EPL-C8200 Revision A Figure 1-48. Wiring Diagram - §12 Chapter A Appendix A-56...
Page 529: Wiring Diagram - §13
EPSON ColorPage EPL-C8200 Revision A A.3.3.13 Wiring Diagram - §13 Table A-35. Wiring Diagram - §13 Signal Name Description TEST PRINT ON (L) 5VDC Setting this signal to LOW (connecting to SG) activates the internal test print. Chapter A Appendix...
Page 530 EPSON ColorPage EPL-C8200 Revision A Figure 1-49. Wiring Diagram - §13 Chapter A Appendix A-58...
Page 531: Component Layout
EPSON ColorPage EPL-C8200 Revision A A.4 Component Layout Figure 1-50. C287MAIN (1) Chapter A Appendix A-59...
Page 532 EPSON ColorPage EPL-C8200 Revision A Figure 1-51. C287MAIN (2) Chapter A Appendix A-60...
Page 533: Circuit Diagrams
EPSON ColorPage EPL-C8200 Revision A A.5 Circuit Diagrams See the following pages for the C287MAIN board circuit diagrams. Chapter A Appendix A-61...
Page 534 C287MAIN 1/7...
Page 535 C287MAIN 2/7...
Page 536 C287MAIN 3/7...
Page 537 C287MAIN 4/7...
Page 538 C287MAIN 5/7...
Page 539 C287MAIN 6/7...
Page 540 C287MAIN 7/7...
Page 541: Optional Paper Cassette Units
EPSON ColorPage EPL-C8200 Revision A A.6 Optional Paper Cassette Units This section provides information on Large Capacity Paper Unit and Paper presence/absence detection signal 500-Sheet Paper Cassette Unit. Each slot (feeder) holds a standard Paper near end detection signal universal cassette. (Optional A3W cassette can not be used.) The...
Page 542 EPSON ColorPage EPL-C8200 Revision A ENVIRONMENTAL CONDITION ELECTRICAL SPECIFICATIONS Operating: Same as for the printer. Electrical specifications are the same as for the printer when the Large Capacity Paper Unit or 500-Sheet Paper Cassette Unit is connected to Storage: Same as for the printer.
Page 543: Installation
EPSON ColorPage EPL-C8200 Revision A A.6.1.2 Installation A.6.1.3 Parts List (Large Capacity Paper Unit) Follow the steps below when installing the Large Capacity Paper Unit / Table A-37. 500-Sheet Paper Cassette Unit. Parts List - Large Capacity Paper Unit (1/3) PL No.
Page 544 EPSON ColorPage EPL-C8200 Revision A Table A-38. Table A-39. Parts List - Large Capacity Paper Unit (2/3) Parts List - Large Capacity Paper Unit (3/3) PL No. Part Name PL No. Part Name PL22.1.15 SIZE SWITCH ASSEMBLY PL22.2.32 TRAY N/P ACTUATOR PL22.1.16...
Page 545: Exploded Diagrams (Large Capacity Paper Unit)
EPSON ColorPage EPL-C8200 Revision A A.6.1.4 Exploded Diagrams (Large Capacity Paper Unit) Figure A-53. PL21.1 Feeder 2 Figure A-52. PL20.1 Feeder 1 Chapter A Appendix A-73...
Page 546 EPSON ColorPage EPL-C8200 Revision A Figure A-55. PL22.2 Feeder 4 Figure A-54. PL22.1 Feeder 3 Chapter A Appendix A-74...
Page 547: Wiring Diagrams (Large Capacity Paper Unit)
EPSON ColorPage EPL-C8200 Revision A A.6.1.5 Wiring Diagrams (Large Capacity Paper Unit) Figure 1-56. Master Wiring Diagram Chapter A Appendix A-75...
Page 548: 500-Sheet Paper Cassette Unit
EPSON ColorPage EPL-C8200 Revision A A.6.2 500-Sheet Paper Cassette Unit A.6.2.3 Parts List (500-Sheet Paper Cassette Unit) Table A-40. A.6.2.1 Product Specifications Parts List - 500-Sheet Paper Cassette Unit See Section A.6.1.1 for the product specifications for the 500-Sheet PL No.
Page 549: Exploded Diagrams (500-Sheet Paper Cassette Unit)
EPSON ColorPage EPL-C8200 Revision A A.6.2.4 Exploded Diagrams (500-Sheet Paper Cassette Unit) Figure A-58. PL21.1 Feeder 2 Figure A-57. PL40.1 Chapter A Appendix A-77...
Page 550 EPSON ColorPage EPL-C8200 Revision A Figure A-59. PL22.1 Feeder 3 Figure A-60. PL22.2 Feeder 4 Chapter A Appendix A-78...

Epson ColorPage EPL-C8200 Service Manual

Table of Contents

Features

Specifications

Interface Specifications

Control Panel

Service Functions

Panel Setting

Table of Contents

Print Process

Print Data Flow

Driver Power Transmission Path

Paper Transportation

Main Components

Operation Modes

Controls

Controller Operating Principles

Table of Contents

Overview

Disassembly/Assembly Procedures

Adjustment

Table of Contents

Overview

Diagnostics by the Diagnostic Commander

Quick Links

Chapters

Troubleshooting

Related Manuals for Epson ColorPage EPL-C8200

Summary of Contents for Epson ColorPage EPL-C8200