hit counter script
Cisco VIC-2FXS - 3600 Voice Interface Card-Fxs 2600/3600 Connection Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Hardware
  5. VIC-2FXS - 3600 Voice Interface Card-Fxs...
  6. Connection manual
Cisco VIC-2FXS - 3600 Voice Interface Card-Fxs 2600/3600 Connection Manual

Cisco VIC-2FXS - 3600 Voice Interface Card-Fxs 2600/3600 Connection Manual

Connecting voice interface cards to the network
Hide thumbs
Table of Contents

Advertisement

Quick Links

Connecting Voice Interface Cards to the Network
Revised: 11/07/2009, OL-12847-01
This document describes how to connect Cisco voice interface cards to your network. It contains the
following sections:
•
•
•
•
•
•
•
•
•
•
•

Grounding Requirements for Voice Interface Cards

This section tells where to find instructions on how to properly ground voice interface cards on the
following platforms:
•
•
•
Do not work on the system or connect or disconnect cables during periods of lightning activity.
Warning
To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network
Warning
voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some
LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.
Cisco 1700 Series Routers
Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers
Cisco ICS 7750
OL-12847-01
1

Advertisement

Table of Contents
loading

Related Manuals for Cisco VIC-2FXS - 3600 Voice Interface Card-Fxs 2600/3600

Summary of Contents for Cisco VIC-2FXS - 3600 Voice Interface Card-Fxs 2600/3600

  • Page 1: Table Of Contents

    Connecting Voice Interface Cards to the Network Revised: 11/07/2009, OL-12847-01 This document describes how to connect Cisco voice interface cards to your network. It contains the following sections: • Grounding Requirements for Voice Interface Cards, page 1 • Foreign Exchange Station (FXS) Interface Cards, page 3 •...
  • Page 2 Cisco 1700 Series Routers Grounding on a Cisco 1700 series router is done on the router chassis itself, not on the voice interface cards. For information on chassis grounding on Cisco 1700 series routers, see the hardware installation guide for your router.

  • Page 3: Foreign Exchange Station (Fxs) Interface Cards

    Note Cisco 1760 router can support four 4-port FXS/DID VICs, up to a maximum of eight DID ports. The Cisco ICS 7750 also supports 8 FXS ports on the analog station interface 81 (ASI 81), and 16 FXS Note ports on the ASI 160. See the “Processor Cards Feature Summary” chapter in the...
  • Page 4 Connecting Voice Interface Cards to the Network Foreign Exchange Station (FXS) Interface Cards Figure 2 2-Port FXS Card Front Panel (VIC2-2FXS) VIC2- 2FXS SEE MANUAL BEFORE INSTALLATION Figure 3 4-Port FXS/DID Card Front Panel (VIC-4FXS/DID) 4FXS/DID IN USE Connecting FXS Cards Use a standard straight-through RJ-11 modular telephone cable to connect a VIC-2FXS, VIC-4FXS/DID, or VIC2-2FXS to a telephone or fax machine.

  • Page 5: Foreign Exchange Office (Fxo) Interface Cards

    Connecting Voice Interface Cards to the Network Foreign Exchange Office (FXO) Interface Cards Figure 4 Connecting an FXS Card RJ-11 ports SEE MAN UAL BEF ORE INST ALLA TION Straight-through RJ-11-to-RJ-11 cable Fax machine Step 3 Connect the other end of the cable to the RJ-11 port on the telephone or fax machine. Foreign Exchange Office (FXO) Interface Cards A Foreign Exchange Office (FXO) interface connects local calls to a central office or PBX.
  • Page 6 Connecting Voice Interface Cards to the Network Foreign Exchange Office (FXO) Interface Cards For connections outside the building where the equipment is installed, the following ports must be Warning connected through an approved network termination unit with integral circuit protection. Figure 5 2-Port FXO Card Front Panel (VIC-2FXO) SEE MANUAL BEFORE INSTALLATION...
  • Page 7 The stepped offhook resistance is initially set to 800 Ohms, then adjusts to 50 Ohms when ringing voltage is not present. To enable soft-offhook command on the port, and to access the connection command with plar opx syntax, see the Cisco Command Lookup Tool. OL-12847-01...

  • Page 8: Receive And Transmit (E&M) Interface Cards

    Connecting Voice Interface Cards to the Network Receive and Transmit (E&M) Interface Cards Receive and Transmit (E&M) Interface Cards RecEive and transMit (E&M) is a signaling technique for two-wire and four-wire telephone and trunk interfaces. The E&M interface typically connects remote calls from an IP network to a PBX. The cards are illustrated in Figure 9 Figure...

  • Page 9: Fxs, Fxo, And E&M Interface Card Leds

    Connecting Voice Interface Cards to the Network FXS, FXO, and E&M Interface Card LEDs Figure 11 Connecting the 2-Port E&M Card RJ-48C ports E&M SEE MAN UAL BEF ORE INST ALLA TION Straight-through RJ-48C-to-RJ-48C cable RJ-48C wall jack Connect the other end of the cable to an RJ-48C wall outlet. Step 3 FXS, FXO, and E&M Interface Card LEDs Each voice interface card has IN USE LEDs, one for each port.
  • Page 10 Note The ISDN BRI restrictions in this section do not apply to the VIC2-2BRI-NT/TE voice interface cards. Note The ISDN BRI restrictions in this section do not apply to the Cisco 1751, Cisco 1760, or Cisco ICS 7750 Note platforms.
  • Page 11 Connecting Voice Interface Cards to the Network ISDN BRI Interface Cards If you install any of the following configurations, the Cisco IOS software disables certain ports, as shown Table • An ISDN BRI voice interface card in a 1-slot voice network module (NM-1V) Two ISDN BRI voice interface cards in a 2-slot voice network module (NM-2V) •...
  • Page 12 Connecting Voice Interface Cards to the Network ISDN BRI Interface Cards Figure 15 Connecting the 2-Port ISDN BRI Card RJ-45 ports MAN UAL 2B-S /T TE BEF ORE ISDN BRI S/T 1 INTA LLAT ION ISDN BRI S/T 0 Straight-through RJ-45-to-RJ-45 cable NT1 device S/T port...

  • Page 13: Analog Direct Inward Dial (Did) Interface Cards

    (FXS) Interface Cards” section on page Note Cisco 2600XM series, Cisco 2691, Cisco 2800 series, Cisco 3600 series, Cisco 3700 series, and Cisco 3800 series routers support DID on the 4-port FXS/DID cards in Cisco IOS Release 12.3(14)T and later. Figure 16...
  • Page 14 Install the grounding lug on the router. See the hardware installation guide for your router for detailed Step 1 instructions. (Grounding on the Cisco 1700 series routers is done on the router chassis, and does not need a grounding lug.) Confirm that the router is still turned off.

  • Page 15: Multiflex Trunk Interface Cards

    Connecting Voice Interface Cards to the Network Multiflex Trunk Interface Cards Multiflex Trunk Interface Cards Multiflex trunk interface cards support generic 1- or 2-port T1 or E1 trunk interfaces for voice, data, and integrated voice and data applications. These cards provide basic structured and unstructured service for T1 or E1 networks.
  • Page 16 64-channel echo canceler module for multiflex trunk (EC-MFT-64) • For information on echo canceler expansion module installation, see the Installing Echo Canceler Expansion Modules on Cisco Interface Cards document. Figure 19 for a sample 1-port multiflex trunk interface card, and...
  • Page 17 Connecting a Multiflex Trunk Interface Card For this connection, use the straight-through RJ-48C-to-RJ-48C cable that came with your card. Note Cisco Modular Access Router Specifications for network-end connectors and pinouts of the cables connecting voice cards. Look under the type of interface card.

  • Page 18: Centralized Automated Message Accounting Trunk Protocol Interface Cards

    Public Service Answering Point (PSAP) using analog CAMA trunks. The CAMA protocol provides in-band signaling. For the NM-HD-1V, NM-HD-2V, and NM-HD-2VE voice network modules, and for the Cisco 1751 and Note 1760 routers, CAMA is supported by the VIC2-2FXO interface card. The VIC-2CAMA card cannot be used with the NM-HD-1V, NM-HD-2V, or NM-HD-2VE voice network modules, or with the Cisco 1751 or Cisco 1760 routers.

  • Page 19: Related Documentation

    Understanding and Troubleshooting Analog E & M Interface Types and Wiring Arrangements, tech • note • Understanding and Troubleshooting Analog E&M Start Dial Supervision Signaling, tech note E&M Cable Pinouts to Connect Cisco 1750/2600/3600 E&M VIC to Nortel PBX Option 11 E&M • Trunk, tech note OL-12847-01...
  • Page 20 G.703 Configuration for Multiflex Voice/WAN Interface Cards on Cisco 2600 and 3600 Series Routers, Cisco IOS Release 12.1(1)T feature module • Configuring 1- and 2-Port T1/E1 Multiflex Voice/WAN Interface Cards on Cisco 2600 and 3600 Series Routers, Cisco IOS Release 12.0(7)T feature module Analog Centralized Automatic Message Accounting E911 Trunk •...

  • Page 21: Obtaining Documentation, Obtaining Support, And Security Guidelines

    Flip Mino, Flipshare (Design), Flip Ultra, Flip Video, Flip Video (Design), Instant Broadband, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn, Cisco Capital, Cisco Capital (Design), Cisco:Financed (Stylized), Cisco Store, Flip Gift Card, and One Million Acts of Green are service marks;...
  • Page 22 Connecting Voice Interface Cards to the Network Obtaining Documentation, Obtaining Support, and Security Guidelines OL-12847-01...

This manual is also suitable for:

Voice interface card

Table of Contents