Advertisement
Quick Links
Advertisement
Related Manuals for Asus PG49WCD
Summary of Contents for Asus PG49WCD
- Page 1 ASUS Service Manual LED Monitor 49" PG49WCD...
- Page 2 ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or infringement under this Warranty Statement. This limit also applies to ASUS’ suppliers and its reseller. It is the maximum for which ASUS, its suppliers, and your reseller are collectively responsible.
- Page 3 Table of Contents Description Page SAFETY PRECAUTIONS..................... 1 EXPLODED VIEW ......................2 DISASSEMBLY AND ASSEMBLY PROCEDURES ............. 4 TROUBLE SHOOTING ....................20...
- Page 4 Revision History Date Revision Page Description 2023/09/08 Initial Release Second Release 2023/09/15 Update Ch.3_DISASSEMBLY AND ASSEMBLY PROCEDURES Third Release 2023/12/12 modify the Exploded BOM of Ch.2 Fourth Release 2023/12/21 modify the Exploded BOM of Ch.2...
- Page 5 1. Safety Precautions Caution To ensure safety from fire, electric shock,injury, harmful for people and MNT , the servicing instructions are for use repair station only. These are mandatory requirements, make sure read the manual before servicing. WARNING Please follow this service manual use of substitute replacement parts which do not have the same, specified safety characteristics, might create shock fire or other hazards.
- Page 7 Exploded BOM ITEM DescCRIPTION Q'ty Panel AC IN CABLE PWR BD TO DC BD&MB CABLE MB TO T-CON BD CABLE MB TO TOP-LED BD CABLE MB TO DOWN-LED BD CABLE DC BD TO MB CABLE MB TO TOP-USB BD FFC CABLE T-CON BD-SOURCE BD FFC CABLE MB TO COVERGENCE BD FFC CABL MB TO T-CON BD FFC CABLE...
- Page 8 3. Disassembly and Assembly Procedures 3.1 Disassembly SOP Preparation before disassemble: 1. The person who repairs the machine must wear an electrostatic ring and gloves. 2. Make sure that the repaired table is clean before repairing. 3. Make sure the torque of the screw is correct. 4.
- Page 9 3-1.拆按键 2PCS 螺丝 3-1. Remove the key 2PCS screw 3-2.撕掉线材上面 1PCS 胶带 3-2. Remove 1 piece of adhesive tape from the wire 3-3．拆 LED 灯罩 6PCS 螺丝 3-3. Remove 6 screws from the LED lampshade 3-4.撕掉按键板 2PCS 导电泡棉 3-4. Tear off 2PCS conductive foam from the button board 3-5.拔下按键...
- Page 10 5-1.撕除固定线材 3PCS 胶带 5-1. Tear off 3 pieces of fixed wire and tape 6-1.打开钢琴盖拔下 2PCS FFC 线，拔电 源排线/排线 6-1. Open the piano cover, unplug 2PCS FFC cable, and unplug the power cable/cable 7-1.拆电源板 4pcs+接地 1PCS+AC 接口 2PCS+主板 3pcs+小板 4PCS 7-1. Remove 4pcs of power board+1pcs of grounding+2pcs of AC interface+3pcs of motherboard+4pcs of small board 8-1.拆主板...
- Page 11 10-1. 撕掉主板 BKT 1pcs 导电泡棉+接口 1PCS 导电布 10-1. Tear off the motherboard BKT 1pcs conductive foam+interface 1PCS conductive cloth 11-1. 打开钢琴盖拔下 FFC 线 11-1. Open the piano cover and unplug the FFC cable 12-1. 拆下 BKT4pcs 螺丝 12-1. Remove the BKT4pcs screws 13-1.
- Page 12 15-1. 拆下 T-CON &排线&FFC 线 15-1. Remove T-CON&flat cable&FFC cable 16-1.打开钢琴盖拔下 FFC 线与拔下排线 16-1. Open the piano cover, unplug the FFC cable and unplug the ribbon cable 17-1. 撕掉 BKT 2PCS 导电泡棉 17-1. Tear off BKT 2PCS conductive foam 18-1. 撕掉 BKT 8PCS 散热胶 18-1.
- Page 13 20-1. 撕掉背板 1PCS 麦拉 20-1. Tear off 1 PCS of backing plate, Myra 21-1. 拆中框 8PCS 螺丝 21-1. Remove 8 screws from the middle frame 22-1. 拆中框 22-1. Remove the middle frame 23-1. 拆大后壳 23-1. Removing the rear housing 24-1. 拆前框 23PCS 螺丝 24-1.
- Page 14 25-1. 取下前框 25-1. Remove the front frame 3.2 Assembly process Descriptions Refer photos 1-1. 组装前框，从底部向上卡合 1-1. Assemble the front frame and snap it from the bottom up 2-1. 锁前框 23PCS 螺丝 2-1. Lock the front frame with 23 screws 3-1. 更换 4PCS 背胶/撕掉离型纸 3-1.
- Page 15 4-3. Engage the ground side and lift the front frame to confirm it is in place. Install in the sequence shown in the figure 5-1. 安装中框 5-1. Install the middle frame 6-1. 贴麦拉 6-1. Tiemai La 7-1. 锁中框 8PCS 螺丝 7-1.
- Page 16 9-1. 贴 BKT4 种类 8PCS 散热胶 9-1. Apply BKT4 type 8PCS heat dissipation adhesive 10-1. 贴 BKT 2PCS 导电泡棉 10-1. Stick BKT 2PCS conductive foam 11-1. 插 T-CON &排线&FFC 线 11-1. Insert T-CON&flat cable&FFC cable 12-1. 插线材穿过 BKT 定位摆放 12-1. Inserting wire through BKT for positioning and placement CONFIDENTIAL –...
- Page 17 13-1. 锁 T-CON 板 4PCS 螺丝 13-1. Lock T-CON board with 4 screws 14-1. 贴导电泡棉 1PCS 14-1. Apply conductive foam 1PCS 15-1. 定位摆放锁主板 BKT3pcs 螺丝 15-1. Positioning and placing lock motherboard BKT3pcs screws 16-1. 接地 1PCS+AC 接口 2PCS 16-1. Grounding 1PCS+AC interface 2PCS 16-2.
- Page 18 17-1. 打开钢琴盖插 2PCS FFC 线，插电 源排线/排线 17-1. Open the piano cover and plug in 2PCS FFC cable, then plug in the power cable/cable 18-1. 贴固定线材 3PCS 胶带 18-1. Apply 3PCS adhesive tape to fix the wire 19-1. 插长线材与 LED 板对接，安装如图 颜色卡合...
- Page 19 20-1. 2PCS 固定线材胶带 20-1. 2PCS fixed wire tape 21-1. 打开钢琴盖插按键 FFC 线 21-1. Open the piano cover and insert the button FFC cable 21-2. 贴按键板 2PCS 导电泡棉 21-2. Paste 2 pieces of conductive foam on the button board 22-1. 贴 LED 灯漏光 4PCS 胶带 22-1.
- Page 20 24-1. 轻轻的抬起后壳，插按键线与 LED 线，盖后壳 24-1. Gently lift the rear cover, insert the button cable and LED cable, and cover the rear cover 25-1. 锁后颗 2PCS 螺丝 25-1. Lock the rear 2 screws 26-1. 卡底座/脖子 26-1. Card base/neck CONFIDENTIAL – DO NOT COPY Page 16 / 20 File No.
- Page 21 3.3 Twist force for screw Descriptions Refer photos Twist force: 2.0+/-0.5kgf.cm (M2.5*3.5L *23PCS) Twist force: 3.5+/-0.5kgf.cm (M3.0*4.0L 8pcs) Twist force: 3.5+/-0.5kgf.cm (M3.0*6.0L 11PCS) Twist force: 3.5+/-0.5kgf.cm (M3.0*6.0L 4pcs) Twist force: 3.5+/-0.5kgf.cm (M3.0*6.0L 2pcs) CONFIDENTIAL – DO NOT COPY Page 17 / 20 File No.
- Page 22 Twist force: 3.5+/-0.5kgf.cm (M3.0*6.0L3pcs) Twist force: 4.0+/-0.5kgf.cm (M3.0*4.0L 3pcs) Twist force: 4.0+/-0.5kgf.cm (M3.0*6.0L 2pcs) Twist force: 4.0+/-0.5kgf.cm (M4.0*6.0L 1pcs) Twist force: 3.5+/-0.5kgf.cm (#3.0*6.0L 2pcs) Twist force: 3.5+/-0.5kgf.cm (M3.0*6.0L 8pcs) CONFIDENTIAL – DO NOT COPY Page 18 / 20 File No. SG-0000946...
- Page 23 Twist force: 3.5+/-0.5kgf.cm (#3.0*6.0L 8pcs) Twist force: 3.5+/-0.5kgf.cm (M4.0*8.0L 2pcs) CONFIDENTIAL – DO NOT COPY Page 19 / 20 File No. SG-0000946...
- Page 24 4. Trouble Shooting Problem Possible Solution Power LED is not ON Press the button to check if the monitor is turned on. Check if the power cord is properly connected to the monitor and the power outlet. Check the Power Indicator function in the OSD menu. Select “ON“...