Safety instructions Keep children below the age of Installation 8 years old at a safe distance Following installation, ensure from the appliance and power that the back cable. of the dishwasher is not freely accessible (protection Before you switch ON the against contact due to hot appliance surface).
Page 6
Safety instructions If the dishwasher is installed Do not install the appliance below or above other near heat sources (radiators, domestic appliances, follow heat storage tanks, cookers the information for installation or other appliances which in combination with generate much heat) a dishwasher and install it under in the installation instructions...
Safety instructions In daily use Deactivating the button lock: Hold down the button + for Read and observe the safety information and instructions approx. 4 sec. until the for use on the packaging display goes out. for cleaning and rinsing agents. When the programme ends on the digital display), the Childproof lock (door lock)
Page 8
Safety instructions Keep children away from Warning detergents and rinse aid. Risk of injury! These may cause chemical Knives and other utensils burns in the mouth, throat with sharp points must be and eyes or asphyxiation. placed in the cutlery basket Keep children away from with the points open dishwasher.
Protection of the environment Protection of the Getting to know your environment appliance P r o t e c t io n o f th e e n v i ro n m e n t G e t tin g to k n o w y o u r a p p l ia n c e Both the packaging of new appliances Diagrams of the control panel and the old appliances themselves...
Water softening system/Special salt To change the setting: Water softening 1. Press programme button 3. system/Special salt Each time the button is pressed, the set value increases by one level; W a t e r s o f te n i n g s y s te m /S p e c i a l s a l t when the value of : has been To ensure good washing results,...
Rinse aid Using special salt Switching off salt refill indicator/water softening Always refill with special salt system immediately before switching on the S w i t c h i n g o f f w a t e r s o f t e n i n g s y s t e m appliance.
Rinse aid 1. Open the dispenser 1b by pressing Setting amount of rinse aid and lifting the plate on the cover. The amount of rinse aid dispensed can be set from : to : . This is the factory setting : Do not change the amount of rinse aid unless streaks (select lower setting) or water stains (select higher setting) are...
Utensils Loading the dishwasher Utensils U te n s ils 1. Remove large food remnants. It is not necessary to prerinse utensils Not suitable under running water. 2. Place the utensils so that Cutlery and utensils made of wood. – they are secure and cannot tip Delicate decorative glasses, craft over.
Utensils Unloading the dishwasher Pans Bottom basket 1Z To prevent water from dripping off the upper basket onto the utensils in the lower basket, it is recommended to empty the appliance from the bottom Hot utensils are sensitive to shock! Therefore, when the programme ends, leave the utensils to cool down in the dishwasher until they can be handled.
Utensils Chopstick basket* F olding spikes * C h o p s t i c k b a s k e t F o l d i n g s p i k e s *depending on the model * depending on model Chopsticks up to a length of 24 cm can The spikes can be folded down to be placed in the chopstick basket.
Detergent Height of utensils Adding detergent If required, the top utensils basket 1* 1. If the detergent dispenser 1j is still closed, press the lock 9" to open can be taken out in order to create more space in the bottom basket for taller the detergent dispenser.
Detergent Notes If the utensils are only lightly soiled, You will obtain optimum rinsing slightly less than the indicated amount and drying results by using solo of detergent is usually adequate. detergents and applying salt and rinse aid separately. Suitable detergents and care products If programmes are short, tablets can be purchased online may not have full cleaning effect...
Overview of programmes Overview of programmes O v e r v i e w o f p r o g r a m m e s The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
Additional options § Programme selection Half load * H a l f l o a d You can select a suitable programme If you have only a few items to wash according to the type of utensils and (e.g. glasses, cups, plates), you can degree of soiling.
Operating the appliance Remaining running time Operating display the appliance When the programme is selected, the O p e r a t in g th e a p p l ia n c e remaining running time of the Programme data programme is indicated on the digital display h.
Operating the appliance Automatic switch off after end To change the setting: 1. Press programme button 3. of programme or interior light* A u t o m a t i c s w i t c h o f f / i n t e r i o r l i g h t Each time the button is pressed, the set value increases by one level;...
Operating the appliance T erminating the programme Intensive drying T e r m i n a t i n g t h e p r o g r a m m e (Reset) The final rinse uses a higher temperature which improves the drying 1.
Cleaning and maintenance Never use a steam cleaner to clean your Cleaning and dishwasher. The manufacturer is not liable for any consequential damage. maintenance Regularly wipe the front of the appliance C le a n i n g a n d m a i n t e n a n c e and fascia with a damp cloth;...
Cleaning and maintenance Filters Spray arms The filters 1B keep large foreign Limescale and contaminants in the objects in the rinsing water away from rinsing water may block nozzles and bearings on the spray arms 12 and the pump. These foreign objects may occasionally block the filters.
Fault, what to do? In this case: Fault, what to do? 1. First disconnect the appliance from F a u l t, w h a t to d o ? the power supply. Experience has shown that you can 2. Remove the filters 1B. rectify most faults which occur in daily 3.
Fault, what to do? Fault table Fault Cause Remedial action “Check water supply” Supply hose kinked. Install supply hose without kinks. display P lights up. Tap turned off. Turn on the tap. Tap jammed or calcified. Turn on the tap. Flow rate must be min.
Page 27
Fault, what to do? Fault Cause Remedial action A different error code is A technical fault has probably Switch off appliances with the ON/OFF switch (. After a short time restart indicated on the digital occurred. display. the appliance. to : If the problem recurs, turn off the tap and pull out the mains plug.
Page 28
Fault, what to do? Fault Cause Remedial action Utensils not dry. No or too little rinse aid in Refill rinse aid. the dispenser. Programme selected without Select programme with drying (see drying. Overview of programmes, Programme sequence). Water collecting in depressions Arrange utensils in a sloping position, on the utensils and cutlery.
Page 29
Fault, what to do? Fault Cause Remedial action Food remnants Utensils placed too closely Arrange utensils with adequate clearance on the utensils. together, utensils basket between them ensuring that the spray jets overfilled. can reach the surface of the utensils. Prevent contact points.
Page 30
Fault, what to do? Fault Cause Remedial action Washable or water-soluble Detergent substances are Change detergent brand. coatings in the container deposited. These coatings cannot Clean appliance mechanically. or on the door. usually be removed with chemicals (appliance cleaner, ...). If there is a “white coating”...
Page 31
Fault, what to do? Fault Cause Remedial action Coloured (yellow, orange, Film formation consisting Check function of the water softening brown), easily removable of ingredients from food system (refill with salt) or, if using combined deposits inside remnants and substances from detergents (tablets), activate water the appliance (mainly the tap water (limescale), “soapy”...
Page 32
Fault, what to do? Fault Cause Remedial action Rust spots on the cutlery. Cutlery not adequately rust- Use corrosion-resistant cutlery. resistant. Knife blades are frequently more severely affected. Cutlery will also rust if rusting Do not wash rusting parts. parts are rinsed at the same time (pan handles, damaged utensil baskets, etc.).
Page 33
Fault, what to do? Fault Cause Remedial action Appliance stops Door not closed properly. Close the door. in the programme Top basket presses against inner Check whether rear panel is being pressed or programme is door and prevents door from in, e.g.
Customer service Customer service Installation and connection C u s to m e r s e r v i c e If you are unable to rectify the fault, In s ta l la t io n a n d c o n n e c t io n please contact your customer service.
Installation and connection Delivery Installation Your dishwasher has been checked The required installation dimensions can thoroughly in the factory to ensure that it be found in the installation instructions. is in working order. This may cause Level the appliance. Ensure that the small water stains.
Installation and connection Drinking water connection Warm water connection * W a r m w a t e r c o n n e c t i o n 1. Fasten the drinking water connection * depending on model to the tap according The dishwasher can be connected to the installation instructions using to cold or hot water up to max.
Installation and connection Electrical connection Removing the appliance Connect the appliance to an Also observe alternating current only, ranging from the sequence of worksteps here. 220 V to 240 V and 50 Hz or 60 Hz 1. Disconnect the appliance from via a correctly installed socket with the power supply.
Installation and connection Transportation Protection against frost P r o t e c t i o n a g a i n s t f r o s t ( E m p t y i n g t h e a p p l i a n c e ) Empty the dishwasher and secure loose If the appliance is in a room where there parts.
Page 40
*9000970308* 9000970308 en (9712) 550MA...