Page 1
LCD-TV Chassis : G3F26CCN G3F32CCN Model : LA26B350F1 LA32B350F1 SERVICE Manual TFT-LCD TV Contents 1. Precautions 2. Product specifications 3. Disassembly and Reassembly 4. Troubleshooting 5. Exploded View & Part List 6. Wiring Diagram LA26B350F1/LA32B350F1 Refer to the service manual in the GSPN (see the rear cover) for the more information.
Page 4
3. Disassembly and Reassembly 3. Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the LA32B350F1 LCD TV. WARNING: This LCD TV contains electrostatically sensitive devices. Use caution when handling these components. 3-1. Disassembly and Reassembly Cautions: 1.
Page 5
3. Disassembly and Reassembly Description Picture Description Screws 2. Lift up rear cover and remove the stand. 3. Remove Screw from the stand BRKT and top BRKT. Lift up the stand BRKT and top.
Page 6
3. Disassembly and Reassembly Description Picture Description Screws 4. Disonnect cable from the boards. 5. Lift up the LCD panel. Reassembly procedures are in the reverse order of disassembly procedures. ※...
Page 7
5. Exploded View & Part List 5. Exploded View & Part List 5-1. LA26B350F1 Exploded View M0013 M0146 M0014 M0215 M0115 M0107 T0003 T0920 M0027 T0175...
1. Precautions 1. Precautions 1-1. Safety Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1-1. Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
1. Precautions 1-2. Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1. Precautions 1-4. Installation Precautions For safety reasons, more than a people are required for carrying the product. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock. Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal temperature may cause fire.
2. Product specifications 2. Product specifications 2-1. Feature & Specifications Model LA26B350F1 Feature RF, 1-HDMI, 1-HDMI/DVI, 1-Component, 1-AV, D-sub � Brightness : 450cd/m � Contrast Ratio : 3000:1 � Response time : 8ms � Dynamic contrast, PVA, TN � PIP(in HDMI 1, 2, 3, Component 1, PC Mode and Sub picture is available only in TV analog mode) �...
Page 31
2. Product specifications Model LA32B350F1 Feature RF, 1-HDMI, 1-HDMI/DVI, 1-Component, 1-AV, D-sub � Brightness : 450cd/m � Contrast Ratio : 3000:1 � Response time : 8ms � Dynamic contrast, Super-PVA � PIP(in HDMI 1, 2, 3, Component 1, PC Mode and Sub picture is available only in TV analog mode) �...
Page 32
2. Product specifications CHANNEL FREQUENCY TABLE OUTPUT FREQUENCY : ANALOG fv:45.75MHz, fs:41.25MHz DIGITAL Fc:44MHz TUNING STEP SIZE : FIRST PLL 250KHz SECOND PLL 62.5KHz OSD CH NO CH NO CH NO CH NO Air-DTV Air-NTSC BAND Cable STD BAND Cable HRC Cable IRC 72.
Page 33
2. Product specifications OSD CH NO CH NO CH NO CH NO Air-DTV Air-NTSC BAND Cable STD BAND Cable HRC Cable IRC 499.25 ULTRA 498.00 499.25 505.25 ULTRA 504.00 505.25 511.25 ULTRA 510.00 511.25 517.25 ULTRA 516.00 517.25 523.25 ULTRA 522.00 523.25 529.25...
2. Product specifi cations 2-2. Specifi cation Comparison to Old Models Model B350(LA26/32B350F1) Coral (LA26/32A450C1) Design Display Type LCD TV LCD TV Built-in Tuner Resolution 1366 x 768 1366 x 768 LCD Panel TFT LCD Panel 50Hz TFT LCD Panel 50Hz Screen Size 26”/32”...
Page 35
Remark Remote Control & Batteries BN59-00880A (AAA x 2) Power Cord 3903-000172 Cover-Bottom BN63-05618B Samsung Electronics Service center Owner’s Instructions BN68-02101H Warranty Card / Registration Card / Safety Guide Manual AA68-03184A (Not available in all locations) Stand Screw x 4 6002-001294 BN90-02198A(26”)
4. Troubleshooting 4. Troubleshooting 4-1. Troubleshooting Check the various cable connections first. • Check to see if there is a burnt or damaged cable. • Check to see if there is a disconnected or loose cable connection. • Check to see if the cables are connected according to the connection diagram. Check the power input to the Main Board.
Page 37
4. Troubleshooting 4-1-1. No Power The LEDs on the front panel do not work when connecting the power cord. The SMPS relay does not work when connecting the power cord. Symptom The units appears to be dead. The IP relay or the LEDs on the front panel does not work when connecting the power cord if the cables are improperly connected or the Main Board or SMPS is not functioning.
Page 38
Does the digital data appear at the output of LVDS Cable? Change a main PCB ass’y Check a LVDS cable? Replace a lcd panel? Please, Call to Samsung Co. LTD. Caution Make sure to disconnect the power before working on the IP board.
Page 40
4. Troubleshooting 4-1-3. No Video (HDMI - Digital Signal) Symptom Audio is normal but no picture is displayed on the screen. Check the HDMI source Major Check the M-star checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Power Indicator is off.
Page 41
4. Troubleshooting WAVEFORMS Digital Output Data Signal of HDMI(Data)
Page 42
Does the Signal appear at c6025 Change a main PCB ass’y. of IC6003? Check the LVDS cable? Replace the LCD panel? Please, Call to Samsung Co. LTD. Caution Make sure to disconnect the power before working on the IP board.
Page 44
Diagnostics Does the signal appear at C6018, Check a connection harness. C6021 of IC6003? Check a LVDS cable ? Replcelcd panel? Please, Call to Samsung Co. LTD. Caution Make sure to disconnect the power before working on the IP board.
Page 45
4. Troubleshooting WAVEFORMS CVBS Output Signal 4-10...
Page 46
4. Troubleshooting 4-1-6. No Sound Symptom Audio is normal but no picture is displayed on the screen. Check the RF Source Major Check the M-star checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Connect a sound cable.
Page 47
4. Troubleshooting WAVEFORMS The Signal are Inputed to IC1201 The Signal are Inputed to IC1202 4-12...
4. Troubleshooting 4-2. Alignments and Adjustments 4-2-1. General Alignment Instuction Usually, a color LCD-TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync. Use the specified test equipment or its equivalent. Correct impedance matching is essential.
Page 49
4. Troubleshooting 4-3. Factory Mode Adjustments 4-3-1 Entering Factory Mode To enter ‘Service Mode’ Press the remote -control keys in this sequence : - If you do not have Factory remote - control INFO MENU MUTE Power on - If you have Factory remote - control PICTURE ON DISPLAY FACTORY...
Page 52
4. Troubleshooting Control EDID EDID Protect On/Off EDID Type L13_1920_1080 P12_1024_768, P13_1024_768, P12_1366_768, P13_1366_768, P12_1920_1080, P13_1920_1080, L12_1366_768, L13_1366_768, L12_1920_1080, L13_1920_1080 EDID Write(0x4D,0) L13_1920_1080 P12_1024_768, P13_1024_768, SUCCESS P12_1366_768, P13_1366_768, P12_1920_1080, P13_1920_1080, L12_1366_768, L13_1366_768, L12_1920_1080, L13_1920_1080 Video Mute Time 0~99 Sub Option Inch 32”...
Page 53
4. Troubleshooting Hotel Option Hotel Option Hotel Mode On/Off Shop Option Shop Option Shop Mode On/Off Sound Detection Threshold OPTION RANGE SOUND Pilot Threshold M2S Thr High 0~255 M2S Thr Low 0~255 S2M Thr High 0~255 S2M Thr Low 0~255 Carrier1 Threshold Amp On Thr High 0~255...
Page 54
4. Troubleshooting MST69A84HQ VDEC SYNC_LVL 0~255 HPLL_MD HPLL_SPD1 0~63 HPLL_SPD2 0~255 CBCRLP_MD YC_DLY IFCOMP 0~63 SAT_ADJ 0~255 YSEPFLT NOISE_LVL 0~255 Film Det Speed NT 0~255 IPC/MJC Film Det Speed PAL 0~255 Motion Hist Motion History Red Sat 0~30 Color Space Red Hue 0~127 Green Sat...
Page 56
4. Troubleshooting EPA Standard Std Contr 0~100 EPA Standard Std Bright 0~100 Std Sharp 0~100 Std Color 0~100 Std Tint 0~100 Std Backlight 0~10 Adjust Adjust Dynamic Dimming On/Off Dynamic CE Dynamic CE On/Off B Slope On/Off LNA Plus RF Db 0 Level 0~255 RF Db 1 Level...
Page 57
4. Troubleshooting YC_Delay PAL BG YC Delay PAL DK PAL I SECAM BG SECAM DK SECAM L NTSC 358 NTSC 443 AV PAL AV SECAM AV NT358 AV NT443 AV PAL60 Sharpness Sharpness H1 Gain 0~63 H2 Gain 0~63 H3Gain 0~63...
Page 58
4. Troubleshooting Skin X 0~11 Skin Y 0~11 B Slope 0~255 DLC ML 0~255 DLC_MH 0~255 DLC_H 0~255 Skin_SAT 0~15 Skin_Hue 0~127 M_Skin_Hue M_Skin_X 0~11 M_Skin_Y 0~11 Mid_color_level 0~255 M_Mid_color_level 0~255 EEPROM Reset EEPROM Reset EEPROM Reset NVR All Clear On/Off Defect Log ...
Page 59
4. Troubleshooting 4-4. White Balance - Calibration 4-4-1 White Balance -Calibration 1. Calibration AV Calibration Comp Calibration PC Calibration HDMI Calibration 4-4-2 Service Adjustment - You must perform Calibration in the Lattice Pattern before adjusting the White Balance. Color Calibration ...
Page 60
4. Troubleshooting Method of Color Calibration (AV) 1) Apply the NTSC Lattice (N0. 3) pattern signal to the AV IN 1 port 2) Press the Source key to switch to “AV1” mode 3) Enter Service mode 4) Select the “Calibration” menu 5) Select the “AV Calibration”...
4. Troubleshooting 4-4-3 White Balance - Adjustment (low light) (hight light) Sub Bright Sub Contrast 5. W/B R offset R gain G offset G gain B offset B gain (W/B adjustment Condition refer next page) 4-5. HOW TO UPGRADE 4-5-1 Software Upgrade (MSTAR ISP Tool) MSTAR ISP TOOL ...
6. Wiring Diagram 6-3. Connector Functions Connector Functions CN1001 <-> SMPS Supply dimming power from SMPS to Main Board. * defective symptom : abnormal Picture CN2001 <-> Speaker Connection Main Board and Speaker. * defective symptom : No picture CN4007 <-> Function & IR Connection Main Board and Function &...