Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Hot surfaces
instructions
This product is only suitable for well insulated areas or occasional use.
1.
SAFETY
1.1.
ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
9
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products.
Electrical safety information. It is important that the following information is read and understood:
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
9
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or is replaced immediately by a
8
qualified electrician.
If the cable or plug is damaged during use, switch off the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
If an extension reel is used it should be as short as possible and fully unwound before connection. A reel with an RCD fitted is preferred
since any appliance plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be
absolutely sure that the capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we
recommend the use of 2.5mm² section cable.
1.2.
GENERAL SAFETY
WARNING! Disconnect the heater from the mains power supply before carrying out any servicing or maintenance.
‰
Maintain the heater in good order and clean condition for best and safest performance. Replace or repair damaged parts.
9
Locate heater in a suitable work area and keep area clean, tidy and free from unrelated materials. Ensure there is adequate lighting
9
and keep the immediate area in front of the outlet grille clear.
WARNING! In order to avoid overheating, do not cover the heater.
‰
Allow the unit to cool before storage. When not in use, disconnect from the mains power supply and store in a safe, cool, dry, childproof area.
9
Only use the heater standing in the upright position on a level surface.
9
DO NOT use the heater where there are flammable liquids, solids or gases such as petrol, solvents, aerosols etc, or where heat
8
sensitive materials may be stored.
DO NOT place the heater near items that may be damaged by heat, allow at least 2m clearance in front of the heater.
8
DO NOT allow the heater to get wet as this may cause an electric shock, causing damage to the heater and possible personal injury.
8
The appliance shall be disconnected from its power source during service and when replacing parts and, if that the removal of the
9
plug is foreseen, it shall be clearly indicated that the removal of the plug has to be such that an operator can check from any of
the points to which they have access that the plug remains removed.
The heater must not be located immediately below a socket outlet."
8
DO NOT let power lead hang over an edge (i.e. table), or touch a hot surface, lie in the beam of heat, or run under a carpet.
8
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to
9
avoid a hazard.
DO NOT use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
8
DO NOT operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT insert or allow objects to enter any openings of heater as this may cause an electric shock, fire or damage to heater.
8
DO NOT use heater if the power cord, plug or the heater is damaged, or if the heater has become wet.
8
DO NOT use the heater for any purpose other than for which it is designed.
8
DO NOT use a timer or other remote device to operate the heater.
8
DO NOT allow children to touch or to operate the heater.
8
DO NOT site the heater below an electrical socket outlet.
8
DO NOT use the heater without the grille fitted.
8
DO NOT use the heater out of doors. These heaters are designed for indoor use only.
8
DO NOT cover heater when in use, and DO NOT obstruct the air inlet and outlet grilles.
8
© Jack Sealey Limited
Original Language Version
INDUSTRIAL FAN HEATER WITH DUCTING
MODEL NO'S:
DEH10001.V2
Do not cover
DEH2001.V2, DEH3001.V2, DEH5001.V2, DEH10001.V2
DEH2001.V2, DEH3001.V2, DEH5001.V2 &
Issue 3 (1,F)
07/11/23
Advertisement
Related Manuals for Sealey DEH2001.V2
Summary of Contents for Sealey DEH2001.V2
- Page 1 MODEL NO’S: DEH10001.V2 Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
-
Page 2: Specification
Connect the fan heater to the mains (see section 4 for DEH10001). 5.3. Set the thermostat knob to the MAX and let the heater operate at full power. DEH2001.V2, DEH3001.V2, DEH5001.V2, DEH10001.V2 Issue 3 (1,F) 07/11/23 © Jack Sealey Limited... -
Page 3: Maintenance
Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 sales@sealey.co.uk... - Page 4 Room temperature control, with open window detection With distance control option With adaptive start control With working time limitation With black bulb sensor Contact details: Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk, IP32 7AR. www.sealey.co.uk ERP Table 2...
- Page 5 Room temperature control, with open window detection With distance control option With adaptive start control With working time limitation With black bulb sensor Contact details: Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk, IP32 7AR. www.sealey.co.uk ERP Table 2...
- Page 6 Room temperature control, with open window detection With distance control option With adaptive start control With working time limitation With black bulb sensor Contact details: Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk, IP32 7AR. www.sealey.co.uk ERP Table 2...
- Page 7 Room temperature control, with open window detection With distance control option With adaptive start control With working time limitation With black bulb sensor Contact details: Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk, IP32 7AR. www.sealey.co.uk ERP Table 2...