Installation; Din Front/Rear-Mount; Fixing The Front Panel - Pioneer Premier DEH-P470MP Installation Manual
Pioneer deh-p470mp: install guide
Hide thumbs
Also See for Premier DEH-P470MP:
- Operation manual (156 pages) ,
- Service manual (82 pages) ,
- Owner's manual (34 pages)
Table of Contents
Advertisement
Available languages
Available languages
Installation
Note:
• Before making a final installation of the unit, tem-
• If installation angle exceeds 60° from horizontal,
porarily connect the wiring to confirm that the con-
the unit might not give its optimum performance.
nections are correct and the system works proper-
(Fig. 3)
ly.
• Use only the parts included with the unit to ensure
proper installation. The use of unauthorized parts
can cause malfunctions.
60°
• Consult with your nearest dealer if installation
requires the drilling of holes or other modifications
of the vehicle.
• Install the unit where it does not get in the driver's
way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.
• The semiconductor laser will be damaged if it
overheats, so don't install the unit anywhere hot —
for instance, near a heater outlet.
DIN Front/Rear-mount
This unit can be properly installed either from "Front" (conventional DIN Front-mount) or
"Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit
chassis). For details, refer to the following illustrated installation methods.
DIN Front-mount
Installation with the rubber bush (Fig. 4)
Holder
After inserting the holder into the dash-
board, then select the appropriate tabs
according to the thickness of the dash-
Dashboard
board material and bend them.
(Install as firmly as possible using the
182
top and bottom tabs. To secure, bend
the tabs 90 degrees.)
53
Rubber bush
Screw
Removing the Unit (Fig. 5) (Fig. 6)
Frame
5
To remove the frame, extend top and bottom
of the frame outwards in order to unlock it.
(When reattaching the frame, point the side
with a groove downwards and attach it.)
• It becomes easy to remove the frame if
the front panel is released.
Fig. 4
Insert the supplied extraction keys
into the unit, as shown in the figure,
until they click into place. Keeping
the keys pressed against the sides of
the unit, pull the unit out.
Fig. 5
DIN Rear-mount
Installation using the screw holes on the side of the unit
1. Remove the frame. (Fig. 7)
Frame
Fig. 6
2. Fastening the unit to the factory radio mounting bracket.
(Fig. 8) (Fig. 9)
Select a position where the screw holes of the bracket and
the screw holes of the head unit become aligned (are fitted),
and tighten the screws at 2 places on each side. Use either
truss screws (5 × 8 mm) or flush surface screws
(5 × 9 mm), depending on the shape of the screw holes in
.
the bracket
10
Fig. 7
Screw
Factory radio mounting bracket
12
Fixing the Front Panel
If you do not operate the removing and attaching the front panel function, use the supplied fixing screws and
holders to fix the front panel to this unit.
1. Attach the holders to both sides of the front panel. (Fig. 10)
To remove the frame, extend top and bot-
tom of the frame outwards in order to
unlock it. (When reattaching the frame,
point the side with a groove downwards
and attach it.)
• It becomes easy to remove the frame if
the front panel is released.
2. Replace the front panel to the unit. (Fig. 11)
Fig. 8
3. Flip the holders into upright positions. (Fig. 12)
Fig. 9
4. Fix the front panel to the unit using fixing screws. (Fig. 13)
11
Dashboard or Console
13
Fig. 10
<ENGLISH>
Holder
Fig. 11
Fig. 12
Fig. 13
Fixing screw
Fig. 14
- Quick Links:
- Connecting the Units
- Installation
Hide quick links:
Advertisement
Table of Contents
