hit counter script
Kenwood NX-1300DE3 User Manual
  1. Manuals
  2. Brands
  3. Kenwood Manuals
  4. Transceiver
  5. NX-1300DE3
  6. User manual

Kenwood NX-1300DE3 User Manual

Hide thumbs Also See for NX-1300DE3:
Table of Contents

Advertisement

Quick Links

NX-1000 series
USER MANUAL
B5A-3233-00/03_K_EN

Advertisement

Table of Contents
loading

Related Manuals for Kenwood NX-1300DE3

Summary of Contents for Kenwood NX-1300DE3

  • Page 1 NX-1000 series USER MANUAL B5A-3233-00/03_K_EN...

  • Page 2: Table Of Contents

    CONTENTS MODELS COVERED BY THIS MANUAL ............5 NOTIFICATION OF IP67 WATER-RESISTANT MODEL (Full Button Model) ..................6 PREPARATION ....................7 INSTALLING THE ANTENNA ................. 7 INSTALLING THE BELT CLIP ................ 7 INSTALLING/ REMOVING THE BATTERY PACK .......... 8 INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE JACKS ..9 INSTALLING THE SPEAKER/ MICROPHONE OR HEADSET ......
  • Page 3 LCD Model ....................66 Non-LCD Model .................... 67 SCAN......................68 TEMPORARY CHANNEL LOCKOUT ............68 PRIORITY SCAN ..................68 SCAN REVERT .................... 69 DTMF (DUAL TONE MULTI FREQUENCY) CALLS ........70 MAKING A DTMF CALL ................70 Manual Dialing .................... 70 Keypad Auto PTT ..................
  • Page 4 STATUS MESSAGE ..................77 Transmitting ....................77 Receiving ....................77 SHORT MESSAGES ..................78 GPS REPORT ....................78 VOICE OPERATED TRANSMISSION (VOX) ..........79 VOX Type ....................79 VOX Operation ................... 79 Semi-VOX Operation .................. 80 VOX Gain Level ..................80 BACKGROUND OPERATIONS ..............

  • Page 5: Models Covered By This Manual

    MODELS COVERED BY THIS MANUAL The models listed below are covered by this manual: NXDN/ Analog Transceiver NX-1200NV : VHF TRANSCEIVER NX-1200N : VHF TRANSCEIVER NX-1300NU : UHF TRANSCEIVER NX-1300N : UHF TRANSCEIVER DMR/ Analog Transceiver NX-1200DV : VHF TRANSCEIVER NX-1200D : VHF TRANSCEIVER NX-1300DU : UHF TRANSCEIVER NX-1300D : UHF TRANSCEIVER...

  • Page 6: Notification Of Ip67 Water-Resistant Model

    NOTIFICATION OF IP67 WATER-RESISTANT MODEL (Full Button Model) Water Resistance and Maintenance IP67 Water-Resistant Model transceiver conforms to the following standards. IP67: The IP standard is the protection level specified by the international standard IEC 60529. The first numeral indicates the “dust-resistant level” and the second numeral indicates the “water-resistant”...

  • Page 7: Preparation

    PREPARATION INSTALLING THE ANTENNA Screw the antenna into the connector on the top of the Antenna transceiver by holding the antenna at its base and turning it clockwise until secure. INSTALLING THE BELT CLIP If necessary, attach the belt clip using the two Belt clip supplied M3 x 8 mm binding screws.

  • Page 8: Installing/ Removing The Battery Pack

    INSTALLING/ REMOVING THE BATTERY PACK The battery pack is not charged at the factory; charge it before use. Align the battery pack with the back of the transceiver, then press the battery pack and transceiver firmly together until the release latch on the base of the transceiver locks.

  • Page 9: Installing The Cap Over The Speaker/ Microphone Jacks

    INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE JACKS Note: ◆ For the speaker/ microphone jack, waterproof performance is guaranteed by securing the supplied cap. Waterproof performance will not be guaranteed by connecting an optional speaker/ microphone, etc. ◆ Use the Phillips #1 screwdriver. If you are not using an optional speaker/ microphone or headset, install the cap over the speaker/ microphone jacks.

  • Page 10: Orientation

    ORIENTATION Buttons and Controls Antenna Speaker Microphone Display Battery pack Keypad Standard Button Model Basic Button Model Full Button Model a Selector Rotate to change the operating channel or zone. b Status indicator Lights during a specified mode, based on dealer programming. (Red, Purple, Blue, Light Blue, Green, Yellow, White) c Power switch/ Volume control Turn clockwise to switch ON the transceiver.

  • Page 11: Display

    Display Indicator Description Displays the signal strength. The Monitor or Squelch Off function is activated. Blinks when an incoming call matches your Optional Signaling. The Talk Around function is activated. Scan, Priority Scan, or Site Roaming is in progress. Blinks when the scan is paused.

  • Page 12: Basic Operations

    BASIC OPERATIONS SWITCHING POWER ON/ OFF Turn the Power switch/ Volume control clockwise to switch the transceiver power • The Power on text appears if the Power on text has been set. Turn the Power switch/ Volume control counterclockwise to switch the transceiver power OFF.

  • Page 13: Transmitting

    TRANSMITTING Select the desired zone and channel. Press the button programmed as [Monitor] or [Squelch Off] to check whether or not the channel is free. • If the channel is busy, wait until it becomes free. Press the PTT switch and speak to the microphone. Release the PTT switch to receive.

  • Page 14: Making Individual Calls (Nxdn/ Dmr)

    Making Individual Calls (NXDN/ DMR) You can select a Unit ID/ name from the list to make a call to those parties on a channel. Press the button programmed as [Individual], [Individual + Short Message] or [Individual + Status] to enter Individual Call Mode. Alternatively, press the button programmed as [Menu] to enter Individual •...

  • Page 15: Receiving Group Calls (Nxdn/ Dmr)

    Receiving Group Calls (NXDN/ DMR) When you receive a group call on a channel and the received group ID matches the ID set up on your transceiver, you can hear the caller’s voice. Receiving Individual Calls (NXDN/ DMR) When you receive an individual call on a channel, a ringing tone will sound and the display will show the caller’s ID.

  • Page 16: Accessible Functions

    ACCESSIBLE FUNCTIONS FUNCTION MODE Your transceiver operations vary according to the functions that your dealer has programmed to the transceiver buttons and selector. Refer to “FUNCTIONS LIST” {p. 18} for the available programmable functions. MENU MODE (LCD Model) Many functions on this transceiver are selected or configured through the Menu instead of physical controls.
  • Page 17 Press the [ S ] button to view the function list for the selected category. Press [ <B ] and [ C> ] to select a function item. Press the [ A ] button to return to the category list. •...

  • Page 18: Functions List

    FUNCTIONS LIST PF Button : Functions that can be programmed to the transceiver buttons Menu : Functions that can be accessed using the transceiver Menu Non-LCD : Non-LCD Model Analog : Channels set up for Analog NXDN : Channels set up for NXDN DMR : Channels set up for DMR ✔...
  • Page 19 Non- Menu Function Menu Analog NXDN Display Button Clear – ✔ ✔ ✔ ✔ ✔ CW Message – ✔ ✔ ✔ Direct Channel – ✔ ✔ ✔ ✔ ✔ 1 ~ 5 DR 1 SEL Direct Channel 1 ~ DR 5 ✔...
  • Page 20 Non- Menu Function Menu Analog NXDN Display Button Low Transmit ✔ ✔ ✔ ✔ ✔ ✔ Power Maintenance MAINT ✔ ✔ ✔ ✔ ✔ Manual Site Hunt M SITE H ✔ ✔ ✔ ✔ Medium Transmit ✔ ✔ ✔ ✔ Power Menu –...
  • Page 21 Non- Menu Function Menu Analog NXDN Display Button Scan SCAN ✔ ✔ ✔ ✔ ✔ ✔ Scan Delete/Add SCN D/A ✔ ✔ ✔ ✔ ✔ ✔ Scrambler/ SCRENC ✔ ✔ ✔ ✔ ✔ ✔ Encryption Scrambler/ SCRENC ✔ ✔ ✔ ✔...
  • Page 22 Non- Menu Function Menu Analog NXDN Display Button Zone Down – ✔ ✔ ✔ ✔ ✔ (Continuous) Zone Select * – ✔ ✔ ✔ ✔ Zone Up/Down * – ✔ ✔ ✔ Zone Up – ✔ ✔ ✔ ✔ ✔ Zone Up –...

  • Page 23: Functions Overview

    FUNCTIONS OVERVIEW Following is a brief overview of the functions available on the transceiver accessible using the Menu and/or programmable to the transceiver buttons. • For details on functions that are not included in “FUNCTIONS OVERVIEW” and “FUNCTION DESCRIPTIONS” {p. 66}, please consult your dealer. None [Analog/ NXDN/ DMR] No function has been programmed.
  • Page 24 Backlight [Analog/ NXDN/ DMR] Allows you can turn the LCD display backlight on/off. PF Button: Press the programmed button to turn the display backlight On or Off. • If Auto backlight is activated by your dealer, the backlight can be set to activate by button operations or when receiving a call/ message.
  • Page 25 Broadcast [DMR] Allows you to make a Broadcast Group Call. Broadcast Group Call can be used to engage in one-way informative group voice calls by initiating a call to a group. PF Button: Press the programmed button, to switch to Broadcast Call. Menu Mode: Select “BCST”...
  • Page 26 Call 1 ~ 6 [Analog/ NXDN/ DMR] Allows you to send assigned signaling from Call 1 to Call 6. PF Button: Press the programmed button to send a message or initiate a call. Calling Alert [Analog] Allows you to send a calling alert to the other party. Calling alert tones help identify yourself to party members and inform them that you are calling.
  • Page 27 Channel Entry [Analog/ NXDN/ DMR] In Channel Entry Mode, channel can be selected by the same operation as List selection. PF Button: Press the programmed button to enter Channel Entry Mode. Press the [ <B ] and [ C> ] buttons to select your desired channel. Press the [ S ] button to confirm the entry.
  • Page 28 Press the [ S ] button. Press the [ <B ] and [ C> ] buttons to select “2”. Press the [ S ] button. Press the [ <B ] and [ C> ] buttons to select “3”. Press the [ A ] button to delete 1 digit number. Press and hold the [ A ] •...
  • Page 29 Channel Up/ Channel Down [Analog/ NXDN/ DMR] PF Button: Press the programmed button to increase/ decrease the channel number. Channel Up (Continuous)/ Channel Down (Continuous) [Analog/ NXDN/ DMR] PF Button: Hold down the programmed button to continuously increase/ decrease the channel number.
  • Page 30 Direct Channel 1 ~ 5 [Analog/ NXDN/ DMR] Allows you to go directly to Direct Channel 1 ~ 5. PF Button: Press the programmed button to jump to a frequently used zone and channel. • Beep A (1 beep) sounds. Press this button again to return to the formerly selected channel.
  • Page 31 Display Format [Analog/ NXDN/ DMR] Allows you to switch the display between the zone-channel number and the channel name. Zone-channel number Channel name PF Button: Press the programmed button to switch the display between the zone-channel number and the channel name. Menu Mode: Select “DISP FMT”...
  • Page 32 External Microphone Sense [Analog/ NXDN/ DMR] Allow you to set the microphone sensitivity of the external microphone. Menu Mode: Select “EX MIC S” and press the [ S ] button. Press the [ <B ] and [ C> ] buttons to select the microphone sensitivity. •...
  • Page 33 Fixed Volume [Analog/ NXDN/ DMR] Allows you to change the volume level of the tone. PF Button: Press the programmed button to change Low, High, or Off (Tone Off). Menu Mode: 1 Select “FIXED V” and press the [ S ] button. 2 Press the [ <B ] and [ C>...
  • Page 34 Group [Analog/ NXDN/ DMR] Activates Group Call Mode. PF Button: Press the programmed button to enter Group Call Mode (NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200). Menu Mode: Select “GRP MODE” and press the [ S ] button to enter Group Call Mode (NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200).
  • Page 35 Group + Status [Analog/ NXDN/ DMR] Allows you to specify a Group ID to send status messages. PF Button: Press the programmed button to enter Group Call Mode (NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200). Menu Mode: Select “GRP STAT” and press the [ S ] button to enter Group Call Mode (NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200).
  • Page 36 Home Channel [Analog/ NXDN/ DMR] Allows you to jump to home channel (programmed by your dealer). If activated by your dealer, you can set your own Home Channel by selecting your desired channel using Home Channel Select. PF Button: Press the programmed button to jump to home channel. •...
  • Page 37 Individual [Analog/ NXDN/ DMR] Activates Individual Call Mode. PF Button: Press the programmed button to enter Individual Call Mode (NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200). Menu Mode: Select “IND MODE” and press the [ S ] button to enter Individual Call Mode (NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200).
  • Page 38 Individual + Status [Analog/ NXDN/ DMR] Allows you to specify a Unit ID to send status messages. PF Button: Press the programmed button to enter Individual Call Mode (NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200). Menu Mode: Select “IND STAT” and press the [ S ] button to enter Individual Call Mode (NXDN/ DMR) or Selcall Mode (FleetSync/ MDC-1200).
  • Page 39 Low Transmit Power [Analog/ NXDN/ DMR] Turns Low Transmit Power On or Off. When using a channel programmed with medium or high power, this allows you to change the output power to low. PF Button: Press the programmed button to change the output power to Low. •...
  • Page 40 Maintenance [Analog/ NXDN/ DMR] Allows you to display the signal strength and Bit Error Rate (BER) on the LCD when constructing the system or during maintenance. PF Button: Press the programmed button to enter Maintenance Display Mode. Menu Mode: Select “MAINT” and press the [ S ] button to enter Maintenance Display Mode.
  • Page 41 Manual Site Hunt [DMR] Allows you can manually move the Revert Channel to another Channel without waiting for Site Roaming to resume. PF Button: On the Channel of DMR Site Roaming, press the programmed button, the Manual Site Hunt function operates. •...
  • Page 42 Microphone Sense [Analog/ NXDN/ DMR] Allows you to change the internal microphone sensitivity. Menu Mode: Select “MIC SENS” and press the [ S ] button. Press the [ <B ] and [ C> ] buttons to select the microphone sensitivity. •...
  • Page 43 Microphone Type [NXDN/ DMR] Allows you to configure the type of the external microphone to be connected to the transceiver and enables the optimal conditions of the audio quality. Menu Mode: Select “MIC TYPE” and press the [ S ] button. Press the [ <B ] and [ C>...
  • Page 44 Monitor [Analog/ NXDN/ DMR] Allows you to turn the transceiver signaling off, to listen to all calls that are received on the channel. PF Button: Press the programmed button to change the Monitor On. • Beep A (1 beep) sounds. Press this button again to change the Monitor Off.
  • Page 45 OST List [Analog] Allows you to enter OST List mode. PF Button: Press and hold the programmed button to enter OST List Mode. Menu Mode: Select “OST LIST” and press the [ S ] button to enter OST List Mode. Press the [ <B ] and [ C>...
  • Page 46 Priority-channel Select [Analog/ NXDN/ DMR] A Priority channel must be programmed in order for Priority Scan to function. When using a single Priority channel, the transceiver will automatically change to the Priority channel when a call is received on it, even if a call is being received on a normal channel.
  • Page 47 Radio Check (MDC-1200) [Analog] This function is for MDC-1200 Radio Check. Radio Check is a function for checking whether a transceiver is available for calling, such as whether the transceiver is on or whether it is within the communication range. Menu Mode: Select “RD CHK”...
  • Page 48 Radio Uninhibit (MDC-1200) [Analog] This is for MDC-1200 Radio Uninhibit. Radio Uninhibit is a function for reviving a transceiver which has been stunned. Menu Mode: Select “UNINHIB” and press the [ S ] button to enter Radio Uninhibit Mode. Press the [ <B ] and [ C> ] buttons to select the destination ID from the ID List. Press the PTT switch to send Radio Uninhibit command.
  • Page 49 Remote Control [NXDN/ DMR] Allows you to remotely control a specified transceiver from the transceiver. In the NXDN and DMR systems, it allows you to operate the transceiver directly, send a remote control message and control the target transceiver. Note: ◆...
  • Page 50 Menu Mode: Select “RMT CTRL” and press the [ S ] button to enter Remote Control Mode. Press the [ <B ] and [ C> ] buttons to select Unit ID List. Press the [ S ] button to enter Remote Control Message Selection. Press the [ <B ] and [ C>...
  • Page 51 RX Auto Gain Control [NXDN/ DMR] Allows you to set the transceiver to automatically adjust the volume of the receiving sound to a specific level for easy listening. Menu Mode: Select “RX AGC” and press the [ S ] button. Press the [ <B ] and [ C>...
  • Page 52 Scan Delete/Add [Analog/ NXDN/ DMR] Allows you to include or omit each channel in the scan sequence. Select your desired channel. PF Button: Press the programmed button to change the Scan Delete/Add status of the channel. Menu Mode: Select “SCN D/A” and press the [ S ] button to activate/ deactivate the Scan of the channel.
  • Page 53 Scrambler/Encryption [Analog/ NXDN/ DMR] Enables or disables Scrambler (analog) or Encryption (NXDN/ DMR) function. • Voice Scrambler is the function to scramble the audio signal so that the contents of communications can be prevented from being intercepted. • Encryption is the function that enhances secrecy in communications on the digital channels by encrypting voice data.
  • Page 54 Scrambler/Encryption Code [Analog/ NXDN/ DMR] Allows you to change the Scrambler Code/ Encryption Key used in the transmission. PF Button: Press and hold the programmed button to enter Scrambler/ Encryption Code Mode. Menu Mode: Select “SCRENC C” and press the [ S ] button to enter Scrambler/Encryption Code Mode.
  • Page 55 Send the GPS Data [Analog/ NXDN/ DMR] Allows you to send your positioning data to the base station when a GPS speaker/ microphone has been installed. • When the power is turned ON and/or the reception condition of the GPS satellite is poor, positioning may take longer to complete.
  • Page 56 Speaker Type [NXDN/ DMR] Allows you to configure the type of the external speaker and speaker/ microphone to be connected to the transceiver and enables the optimal conditions of the audio quality. Menu Mode: Select “SPK TYPE” and press the [ S ] button. Press the [ <B ] and [ C>...
  • Page 57 Squelch Level [Analog] Allows you to adjust the transceiver squelch level. PF Button: Press the programmed button to enter Squelch Level Adjustment Mode. Menu Mode: Select “SQL LVL” and press the [ S ] button enter Squelch Level Adjustment Mode. Press the [ <B ] and [ C>...
  • Page 58 Stack [Analog/ NXDN/ DMR] Allows you to check the records of received calls and messages received. • 　The “ ” indicator lights up when all stacked data is already read. • 　 When there is unread data, The “ ” indicator blinks. PF Button: Press the programmed button to enter Stack Mode.
  • Page 59 Press the [ <B ] and [ C> ] buttons to select the List. Each time press the [ S ] button to change display type (Message → Caller • ID → Channel No.→ Message→ ). Press the [A] button, delete confirmation is displayed, press the [S] button •...
  • Page 60 Surveillance [Analog/ NXDN/ DMR] Allows you to disable the alert tone, backlight and LED functions. The Surveillance function is used when the change of the transceiver status needs to be kept unnoticed, such as while on　a Public Safety operation. PF Button: Press the programmed button to activate the Surveillance Mode.
  • Page 61 TX Audio Equalizer [NXDN/ DMR] Allows you to set the transmission audio characteristic (Flat, High boost, or Low boost). Menu Mode: Select “TX EQ” and press the [ S ] button. Press the [ <B ] and [ C> ] buttons to select the audio characteristic. Press the [ S ] button to confirm and exit mode.
  • Page 62 [Analog/ NXDN/ DMR] Allows you to adjust the VOX Gain level. PF Button: Press the programmed button to enter VOX Gain Level Adjustment Mode. Menu Mode: Select “VOX LVL” and press the [ S ] button to enter VOX Gain Level Adjustment Mode.
  • Page 63 Zone Delete/Add [Analog/ NXDN/ DMR] Allows you to include or omit each Zone in the Multi-Zone scan sequence. Select your desired zone. PF Button: Press the programmed button to switch the Zone Delete/Add status of the channel. Menu Mode: Select “ZONE D/A” and press the [ S ] button to switch the Zone Delete/Add status of the channel.

  • Page 64: Keypad Operation

    KEYPAD OPERATION The keypad operating method can be selected according to the purpose. Even pressing the [ 0 ] ~ [ 9 ], [ ], [ # ] button, and None button-entry Error Tone will sound and no operation will be performed.
  • Page 65 This function allows you to send DTMF by pressing Keypad without PTT switch. • If DTMF Manual Dialing is Enabled, the DTMF Code is sent by pressing the [ 0 ] ~ [ 9 ], [ ], [ # ] button. Keypad Auto PTT Press the [ 0 ] ~ [ 9 ], [ ], [ # ] button, send the DTMF...

  • Page 66: Function Descriptions

    FUNCTION DESCRIPTIONS For details on functions that are not included in “FUNCTIONS OVERVIEW” {p. 23} and “FUNCTION DESCRIPTIONS”, please consult your dealer. TRANSCEIVER PASSWORD LCD Model If the transceiver is password protected, “PASSWORD” will appear on the display when the power is turned on. To unlock the transceiver, enter the correct password.
  • Page 67 Non-LCD Model If your transceiver is password protected, the LED will light blue when you turn the transceiver ON. Enter the password (up to 6 digits) using the following procedure. Set the Selector to position “1”. Press the Side 1 or Side 2 button to enter the first digit. The Side 1 button increases the digit value and the Side 2 button •...
  • Page 68 SCAN Scan is useful for monitoring signals on the transceiver channels. While scanning, the transceiver checks for a signal on each channel and only stops on a channel if a signal is present. To begin scanning, press the button programmed as [Scan]. •...
  • Page 69 SCAN REVERT The Scan Revert channel is the channel selected when you press the PTT switch to transmit during scan. Your dealer can program one of the following Scan Revert channels: Selected: The last channel selected is assigned as the new revert channel. •...
  • Page 70 DTMF (DUAL TONE MULTI FREQUENCY) CALLS Note: ◆ Manual Dialing and Keypad Auto PTT are available only on full button model. MAKING A DTMF CALL Manual Dialing Press and hold the PTT switch. Enter the desired digits using the keypad. •...
  • Page 71 EMERGENCY CALLS If your transceiver has been programmed with the Emergency function, you can make emergency calls. Press and hold the button programmed as [Emergency]. • Depending on the delay time programmed into your transceiver, the length of time you must hold the Emergency button will vary. •...
  • Page 72 SCRAMBLER (ANALOG)/ ENCRYPTION (NXDN/ DMR) Note: ◆ The following types of encryption are available depending on the protocol used. NXDN : Bit scrambling (built-in encryption function) DMR : Bit scrambling (built-in encryption function) and Enhanced Encryption ◆ The Enhanced Encryption is a software option. Ask your dealer for details concerning the Enhanced Encryption settings.
  • Page 73 SELECTING THE ENCRYPTION KEY Press the button programmed as [Scrambler/Encryption Code] to enter Scrambler/Encryption Code Mode. Alternatively, press the button programmed as [Menu] to enter Scrambler/ • Encryption Code Mode using the Menu Mode. 2 Select the new Encryption key using the [ <B ] and [ C> ] buttons. •...
  • Page 74 SIGNALING QUIET TALK (QT)/ DIGITAL QUIET TALK (DQT) [ANALOG] Your dealer may have programmed QT or DQT signaling on your transceiver channels. A QT tone/ DQT code is a sub-audible tone/ code which allows you to ignore (not hear) calls from other parties who are using the same channel. When a channel is set up with a QT tone or DQT code, squelch will only open when a call containing a matching tone or code is received.
  • Page 75 OPTIONAL SIGNALING Your dealer may also program several types of optional signaling for your transceiver channels. 2-tone Signaling [Analog] 2-tone Signaling opens the squelch only when your transceiver receives a call containing a matching 2-tone signal. DTMF Signaling [Analog] DTMF Signaling opens the squelch only when the transceiver receives a call containing a matching DTMF code.
  • Page 76 FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION FleetSync is an Alphanumeric 2-way Paging Function, and is a protocol owned by JVCKENWOOD Corporation. FleetSync enables a variety of paging functions on your transceiver, some of which depend on dealer programming. Note: ◆ This function is available only in analog operation. SELCALL (SELECTIVE CALLING) A Selcall is a voice call to a station or group of stations.
  • Page 77 Identification Codes An ID code is a combination of a 3-digit Fleet number and a 4-digit ID number. Each transceiver has its own ID. • Enter a Fleet number (100 ~ 349) to make a fleet call. • Enter an ID number (1000 ~ 4999) to make an individual call in your fleet. •...
  • Page 78 SHORT MESSAGES This transceiver can receive short data messages which contain a maximum of 48 characters. GPS REPORT GPS data can be manually transmitted by pressing the button programmed as [Send the GPS Data], or by accessing the Menu. If set up by your dealer, GPS data may be automatically transmitted at a preset time interval.
  • Page 79 VOICE OPERATED TRANSMISSION (VOX) VOX (VOX/ Semi-VOX) operation allows you to transmit hands-free. This feature can be activated or deactivated by your dealer. To operate VOX, you must use an optional headset. VOX Type VOX: When the voice level to the microphone is higher than the reference level (VOX Gain Level), the transceiver automatically starts transmission.
  • Page 80 Semi-VOX Operation Connect a headset to the transceiver. • The VOX function does not activate when a headset is not connected to the accessory terminal of the transceiver. Press the button programmed as [VOX Function]. Alternatively, you can press the button programmed as [Menu] to enter •...
  • Page 81 BACKGROUND OPERATIONS TIME-OUT TIMER (TOT) The Time-out Timer is used to prevent any caller from using a channel for an extended period of time. If you continuously transmit for a period of time that exceeds the programmed time, the transceiver will stop transmitting and an alert tone will sound. To stop the tone, release the PTT switch.
  • Page 82 VOICE ANNOUNCEMENT An audio voice will be announced as below by dealer setting. • When changing the zone and/or channel, the new zone and channel number are announced. • When changing the function setting, the new setting is announced. - Scrambler/Encryption - VOX Function - Home Channel - Button Lock...
  • Page 83 BUSY CHANNEL LOCKOUT (BCL) If BCL is set up by your dealer, you will be unable to transmit on the channel if it is already in use. Under these circumstances, use a different channel or wait until the channel becomes free. However, if BCL Override has also been programmed, you can transmit over the current signal: Press and hold the PTT switch.
  • Page 84 © 2022...

This manual is also suitable for:

Nx-1200nvNx-1200nNx-1300nuNx-1300nNx-1200dvNx-1200d ... Show all

Table of Contents