Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for AEG PERFEKT GLIDE 30-1
Summary of Contents for AEG PERFEKT GLIDE 30-1
- Page 1 PERFEKT GLIDE 30-1 30” Built-in Telescopic Range Hood...
- Page 2 • Top vent for exterior ventilation ELECTRICAL REQUIREMENTS • 115 Volt, 60Hz, 15AMP • AEG Range Hoods are supplied with a Canadian cord and plug • 5/16 Electrical cord located 6 ” (160mm) from the top right corner of the unit at the rear Specifications are subject to change without notice V1.5...
-
Page 3: Range Hood Dimensions
Specifications PERFEKT GLIDE 30-1 FRONT PANEL - DUCTED ” 13/16 ” 42mm 758mm RANGE HOOD DIMENSIONS 13/16 D: 11” x W: 29 ” D: 280mm x W: 758mm Specifications are subject to change without notice V1.5... -
Page 4: Specifications
Specifications PERFEKT GLIDE 30-1 CABINET BOX DESIGN 30” 762mm Shelf Supports Range hood 9/16 ” 166mm ” 210mm FRONT VIEW SIDE VIEW Specifications are subject to change without notice V1.5... -
Page 5: Front Panel Installation
Specifications PERFEKT GLIDE 30-1 FRONT PANEL INSTALLATION 9/16 ” 166mm NOTE: Removing the front stainless steel trim • 1. Pull the glide forward • 2. Remove the 4 screws holding the glide to the panel • 3. Install the matching front panel using the 4 screws... - Page 6 Specifications PERFEKT GLIDE 30-1 ” 42mm NOTE: Cabinet Door Panel Height • Ensure that the cabinet door panel is lengthened to accommodate the smaller sized Range Hood Front Panel Specifications are subject to change without notice V1.5...
-
Page 7: Damper Installation
Specifications PERFEKT GLIDE 30-1 DAMPER INSTALLATION 120mm 271.5mm ” 11/16 ” 139.7mm 168.5mm ” ” 281.5mm 100mm 1/16 15/16 ” ” SECURING THE DAMPER • Drill (1/8”) at the points located • Secure the damper to the motor housing using the screws supplied... - Page 8 Specifications PERFEKT GLIDE 30-1 DAMPER INSTALLATION (SHELF CUT-OUT) • Shelf with less than 1” of shelf extension MUST HAVE a support brace in place 175mm ” 221.5mm 220mm 11/16 ” ” 100mm 15/16 ” DAMPER CUT-OUT • W: 220mm x D:175mm...
- Page 9 Specifications PERFEKT GLIDE 30-1 DAMPER INSTALLATION (SHELF CUT-OUT) • Shelf with 1” or more extension does not require a support brace. 175mm ” 221.5mm 220mm 11/16 ” ” 100mm 15/16 ” DAMPER CUT-OUT • W: 220mm x D:175mm 11/16 W: 8 ”...
-
Page 10: Alternate Installation
ALTERNATE INSTALLATION PERFEKT GLIDE 30-1 (REC) REMOVE THE FILTER • To remove the filter press on the tab to release the filter • While depressed, pull the filter towards you to remove it from the filter housing. Specifications are subject to change without notice... - Page 11 ALTERNATE INSTALLATION PERFEKT GLIDE 30-1 (REC) LOCATE PRE-DRILLES HOLES • While depressed, pull the filter towards you to remove it from the filter housing. • Locate the pre-drilled pilot holes in the cavity of the Glide Range hood Specifications are subject to change without notice...
- Page 12 ALTERNATE INSTALLATION PERFEKT GLIDE 30-1 (REC) Cut-out for exhaust (Glide 24-1 Models Only) SECURING THE GLIDE RANGE HOOD • Use #10 ¾” (19mm) wood screws • Screw the Glide Range hood to the support shelf in the cabinet Specifications are subject to change without notice...
- Page 13 Specifications PERFEKT GLIDE 30-1 RECOMMENDED CABINET MINIMUM CLEARANCE (GAS COOKING SURFACE) 30” (762mm) Specifications are subject to change without notice V1.5...
- Page 14 Specifications PERFEKT GLIDE 30-1 RECOMMENDED CABINET MINIMUM CLEARANCE (ELECTRIC / INDUCTION COOKING SURFACE) 30” (762mm) 24” (610mm) Specifications are subject to change without notice V1.5...
- Page 15 AEG Appliances are designed and manufactured to the highest standards. Each appliance is covered by a comprehensive 2-year parts and labour warranty. Refer to product warranty policy for complete terms and conditions. FOR PARTS AND SERVICE Euro-Parts & Service 39822 Belgrave Road, Belgrave, ON. N0G 1E0 1 800 678 8352 (Canada) •...