Advertisement
Available languages
Available languages
Before Operating Your Dryer
Read your dryer Owner's Guide. It has important
safety and warranty information. It also has many
suggestions for best drying results.
To reduce the risk of fire, electric shock
or injury to persons, read the IMPORTANT SAFETY
INSTRUCTIONS in your dryer Owner's Guide before
operating this appliance.
Operating Steps
Read "Drying Procedures" in your Owner's Guide. It
explains these operating steps in detail.
1. Prepare items for drying.
2. Check that lint filter is clean and in place.
3. Load the dryer. If desired, add a dryer fabric
softener sheet. Close the door.
4. Select the appropriate cycle and settings for
each load.
• Turn the Cycle Selector knob to select the cycle.
The estimated drying time will be displayed.
• A suitable drying temperature, dryness level and
options will automatically be indicated for each
cycle. See the "Dryer Setting Chart" for more
details.
• To change the temperature and dryness level,
press Temperature or Dryness until the desired
selections are made.
• To select or delete an option, press Options; then,
while the indicator is blinking, press Select. The
indicator will light when the option has been
selected. it will no longer be lighted when the option
has been deleted.
• If a temperature, dryness level or option is not
available for a cycle, it will not light.
DRYER OPERATING INSTRUCTIONS
• Adjustments to the cycle will be remembered
each time that cycle is selected in the future.
• To return to factory settings, press Start/Pause
and Select at the same time and hold until the
signal sounds.
5. Press Start/Pause to begin the cycle.
• To pause the cycle press Start/Pause. To
resume the cycle, press Start/Pause again.
• To stop or change the cycle, press Cancel.
6. A signal will sound at the end of the cycle and
periodically during Extended Tumble when the
Signal option is selected. When the cycle
ends, remove items immediately and hang or fold.
7. Clean the lint screen after every load.
Cycle Selection
Turn the Cycle Selector knob to the desired cycle. For
best results, follow the fabric care label instructions on
items to be dried. If the selection is changed after the
cycle starts, the indicator lights will blink, the signal
will beep and "ERR" will be displayed. To change the
selection after the cycle has begun, press Cancel
before making another choice. Just turning the knob
to another selection will not change the cycle. The
signal will beep and the status lights will flash, but the
original cycle will continue.
Auto Dry
Auto Dry cycles take the guesswork out of drying time.
Loads dried using the Towels, Heavy Duty, Normal, Perm
Press, and Delicates cycles will dry automatically at
the selected temperature to the desired dryness level.
The dryer uses sensing bars to sense the moisture
level of the load as it tumbles through heated air. Auto
Dry cycles save time and energy and protect fabrics.
The estimated drying time will be displayed for about
5 minutes. Then the display will change to "Ad" to
indicate drying time is automatically being determined
by the sensors. When the load has reached the
selected dryness level, it will continue to tumble,
unheated, during a Cool Down period. This helps reduce
wrinkling and makes items easier to handle during
unloading. The estimated Cool Down time will be
displayed. "dn" is displayed when the cycle is done.
Drying time varies depending on size and dampness of
load and fabric type. If the load is too small or almost
dry, the sensing bars may not detect enough moisture
to continue the cycle and the cycle may end after a few
minutes. Select a Timed Dry setting to dry such loads.
Room temperature and humidity, type of installation and
electrical voltage or gas pressure can also affect drying
time.
Towels
Select this Auto Dry cycle for towel loads.
Heavy Duty
Select this Auto Dry cycle for sturdy work clothes.
Normal
Select this Auto Dry cycle for cotton items.
Perm Press
Select this Auto Dry cycle for cottons and blends with
a no-iron finish.
Delicates
Select this Auto Dry cycle for knits and delicate items.
PN 134598200 (0512)
Advertisement
Table of Contents
Related Manuals for Frigidaire AEQ6000CES0
Summary of Contents for Frigidaire AEQ6000CES0
-
Page 1: Before Operating Your Dryer
1. Prepare items for drying. 2. Check that lint filter is clean and in place. 3. Load the dryer. If desired, add a dryer fabric softener sheet. Close the door. 4. Select the appropriate cycle and settings for each load. -
Page 2: Dryer Features
Touch Up Select Touch Up to help remove wrinkles from clean dry items that may have been left in the dryer, have been stored in crowded closets or drawers or unpacked from luggage following a trip. The load will tumble for 15 minutes at low heat. -
Page 3: Error Code Chart
If the dryer stops, the status lights flash, the signal beeps and a code is displayed, an error has occured. Press CANCEL. Consult the Error Code Chart below or the "Avoid Service Checklist" in the Owner's Guide for the possible cause and solution. Make necessary corrections, then select a cycle and press START. If the dryer stops, the status lights flash again, the beeping continues and the code reappears, please contact service for assistance. - Page 4 CONSIGNES D’UTILISATION DE SECHEUSE Avant de faire fonctionner votre sécheuse Lisez votre Guide du propriétaire de sécheuse. Il contient des informations importantes relatives à la sécurité et à la garantie. Il comprend aussi de nombreuses suggestions pour obtenir des résultats de séchage optimums.
- Page 5 Sélection de cycle (suite) Retouche Sélectionnez Retouche (Touch Up) pour retirer le froissement d’articles secs propres qui ont pu être laissés dans la sécheuse, entreposés dans des garde- robes ou tiroirs surchargés ou retirés des bagages après un voyage. La charge bascule durant 15 minutes à faible chaleur.
- Page 6 Si la sécheuse s’arrête, la lumière d’état clignote, le signal sonore retentit et un code s’affiche : une erreur s’est produite. Appuyez sur Annuler. Pour éviter de recourir à des appels d’entretien, consultez le Tableau de code d’erreur ci-dessous ou la Liste de vérification dans le Guide du propriétaire afin d’identifier la cause et la solution possibles. Faites les corrections nécessaires, sélectionnez ensuite un cycle et appuyez sur Démarrer.