Attention: This service manual is only for service personnel to take reference with. Before servicing please read the following points carefully. Safety precautions 1. Instructions Be sure to switch off the power supply before replacing or welding any components or inserting/plugging in connection wire.
Page 4
would be unable to work and no way to get it repaired. If the connection wires, connections or components fixed by the thermotropic glue need to disengage when service, please soak the thermotropic glue into the alcohol and then pull them out in case of dagmage.
Adjustment Instruction Safety Instructions 1.1 Power supply must be cut off when replacing or welding any component or inserting / pulling out connective lines; 1.2 Anti-electrostatic measures must be carried out during the whole producing processes! Do not touch IC by hands at will; Use anti-electrostatic iron;...
Page 6
3.2 Adjustment flow as Fig. 1: Check if EDID、 HDCP KEY、 FLASH has been written? General assembly and combined adjustment White balance adjustment Input central signal, check TV function (omitted channel, analog parameters control, etc. ), check earphone, speakers output. Check accessory and packing Check AV input, output and relevant functions.
Page 7
Adjustment Instruction 4.1 The unit adjustment 4.1.1 According to the wiring diagram specified by “Product Specification”, connect power/backlight board assembly, data processing assembly, IR/Key board assembly correctly, supply with power, turn on the TV set. Check display. 4.1.2 Factory menu instruction Press key “INPUT”, then press digital keys “2、5、8、0”...
Page 8
4.1.4 ADC calibration for Component channel a) Switch to Component channel; b) Press key “INPUT”, then press digital keys “2、5、8、0” in turn to enter into primary factory menu; c) Move cursor to item “ADC ADJUST” and press key “OK” to enter into the inferior submenu; d) Input Component signal (VG-849 Timing:972(1080i), Pattern:918 100% color bar);...
Page 9
Gain/Offset upward, coordinates of Y will increase, adjust G Gain/Offset downward, coordinates of Y will decrease; Note: Sanyo customer requires that default color temperature is Normal, adjust white balance of color temperature Normal and Cool in Dynamic picture mode; for other customers, please adjust white balance of color temperature Cool in Dynamic picture mode.
Page 10
5.4 D-SUB port Input D-SUB signal from VG-849 with formats listed as Table 3 separately, check picture and sound; if H./V. of picture displays abnormally, enter into main menu Picture->Screen->Auto Adjust to perform auto calibration. Table 3 D-SUB signal formats H.- Freq.
Page 11
Table 5 Video & audio signal formats of digital HDMI Item Unit Parameter Note Deep color:RGB 4:4:4(24 bit/pixel,30 bit/pixel,36 bit/pixel)、 YUV 4:4:4 (24 bit/pixel,30 bit/pixel,36 bit/pixel)、 Video 对于1080p,deep color只支持到30 bit/pixel。 YUV 4:2:2(16 bit)、YUV 4:2:2(20 bit)、YUV 4:2:2(24 bit) Audio sample 32、44.1、48 freqence Audio data...
Software Upgrading Instruction Software Upgrading Instruction as Table 6 Table 6 Software Upgrading Instruction Software SMT before Location Part No. Part model Upgrading method function upgrading Upgrade with ALL100, etc., N103 5272532006 EN25Q32A-100HIP FLASH need write protection, refer to Note1; N105 5272404005 CAT24C04WI-GT3...
Page 13
Fig. 3 Device MX25L64 successful connection If connection is failed, press the first menu “Device” and choose “MX25L64” manually, then press “Connect”; 4) Press “Read”, choose upgrading file, such as “MERGE.bin”; please refer to Fig. 4; Fig. 4 Choosing upgrading file 5)...
Page 14
6) Press “Run” shown as Fig. 4 to perform upgrading in two steps, “Erase” and “Program”; Normal upgrading process: The first step “Erasing…, Flash Status: 03” will last for some time, or erasing is failed if the step passes over immediately; please confirm procedure 2) to perform upgrading again; The second step is “Programming…,Flash Status:00”;...
Working Principle of the Unit 1、 ATV PAL signal flow Receive RF PAL analog signal and sent it to XC5200C (D/A silicon Tuner controlled by main chip MSD309PX through I C bus) to be demodulated, then differential IF signal is send out to main chip MSD309PX analog demodulation to be demodulated to get analog CVBS video signal and SIF sound signal.
Page 16
sent to main chip MSD309PX to be processed by acoustic effect processor and volume controller to get two parts of signals: the analog part of signal is sent to earphone power amplifier MAX9820 to be amplified and then outputted to earphone jack; the digital part of signal I2S is sent to digital audio power amplifier TAS5711 to be processed by D/A convertor and power amplifier, then outputted to drive speakers.
IC Block Diagram 1、 TUNER IC XC5200C The Single-Chip Multi-Standard Tuner XC5200C supports all analog TV formats transmitted worldwide in the 42-1000 MHz band on either cable or terrestrial broadcast channels. It implements on-chip tuning, and channel filtering without external (SAW) filters and has no manually tunable parts. The broadband tuner converts the selected channel into an Intermediate Frequency (IF), which is then sampled by an internal high-resolution analog-to-digital converter (A/D) for further processing.
Page 19
2、 AMP IC TAS5711 The TAS5711 is a 20-W, efficient, digital audio power amplifier for driving stereo bridge-tied speakers. One serial data input allows processing of up to two discrete audio channels and seamless integration to most digital audio processors and MPEG decoders.
Page 20
3、 AUDIO IC MAX9820 The MAX9820 Windows Vista®-compliant stereo headphone amplifier is designed for portable Equipment where board space is at a premium. It features Maxim’s DirectDrive® architecture to produce a ground-referenced output from a single supply, eliminating the large output-coupling capacitors required by conventional single-supply headphone amplifiers.
Troubleshooting Block Diagram 1.Panel doesn’t light up. Supply with power, check if red indicator lights up in STANDBY state? Press key POWER on remote control or unit, check indicator. Check if 5V is supplied Blue to X601-PIN3 ? Check if level of X601-PIN1 on main Check STANDBY...
Page 23
No picture, but backlight is normal: 2. Can control the TV set Press key MENU, by keys on remote can OSD display control or the unit? normally? Do no channel have picture at all? 有 Enter into factory menu to initialize EEPROM, then cut off main power and then turn on the TV set again, check if there is picture?
Page 24
No sound, but picture is normal: 3. No sound Check if level of Check there Check N607-PIN19&25 signal inputted (signal input are all high? N607-PIN15&20&21 circuits) on main &22 ? board. Check +24V on Check if level of Check power voltage power board.
Page 32
PART LIST OF EXPLODED VIEW REF.No. DESCRIPION Front cabinet assembly Front cabinet decorative board IR assembly Light-guided pole Panel pressing block (medium) Speaker assembly Display panel Main board insulated slice (side) Main board assembly Power board assembly Standing pole bracket (right) Standing pole bracket (left) Power board insulated slice Interface baffle (right)
Page 33
PART LIST LED-32XR11F ver. REF.No. PARTS No. DESCRIPION Q'TY REMARK XI6632514010 Front cabinet assembly XI5850447010 Front cabinet decorative board IR assembly XI635KE01403 XI570031901D Light-guided pole Panel pressing block (medium) XI5810078900 XI6170866000 Speaker assembly XI5203328309 Display panel 1 T315HW07 VE Main board insulated slice (side)
Page 34
Appendix: Installing the Stand If the stand is provided, please read these instructions thoroughly before attempting this installation. You must install your TV into the stand in order for it to stand upright on a cabinet or other flat surface. If you intend to mount your TV on a wall or other vertical surface, you must remove the stand column.