Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear safety
instructions
footwear
1. SAFETY
WARNING! ALWAYS USE LOAD RATED STANDS TO SUPPORT LIFTED LOADS
‰
▲
DANGER! Use the jack for lifting and lowering only.
▲
DANGER! DO NOT place any part of the body beneath the lifted load unless the load is fully supported by rated stands.
▲
DANGER! DO NOT place any part of the body beneath the load during lifting or lowering.
DO NOT exceed the rated capacity of the jack, load or maximum stroke.
8
DO NOT adjust the overload valve, modify or use the jack for any purpose other than for which it is designed (lifting and lowering
8
mechanical devices).
DO NOT leave elevated loads unattended, unless safe from others in a garage or workshop.
8
DO NOT modify the jack.
8
Ensure the jacking area is solid and level. Increase the jacking area with a solid flat plate (steel) if jacking on tarmacadum or grass.
9
Keep others away from the work area.
9
Ensure the jacking area is clutter free and that there is adequate lighting.
9
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
‰
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator.
2. INTRODUCTION
Fitted with safety overload valve and manufactured in the EU. All steel, one-piece base, reservoir and pump cylinder design gives added
strength. Fully serviceable ram piston with extension screw. All models supplied with 90° rotating pump and telescopic pump handle. Model
No's PBJ20, PBJ30 and PBJ50 have moulded carry handles incorporating storage for the pump handle. Service kits readily available.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PBJ20 . . . . . . . . . . . PBJ30 . . . . . . . . . . PBJ50
Capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20tonne . . . . . . . . . . 30tonne . . . . . . . . . 50tonne
Hydraulic Lift: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150mm . . . . . . . . . . .150mm . . . . . . . . . . 140mm
Maximum Height: (Leadscrew extended). . . . . . . . . . . .459mm . . . . . . . . . . .467mm . . . . . . . . . . 400mm
Minimum Height: (Leadscrew retracted) . . . . . . . . . . . .234mm . . . . . . . . . . .242mm . . . . . . . . . . 260mm
Screw Extension: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75mm . . . . . . . . . . . .75mm . . . . . . . . . . . . . . *0
Nett Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.89kg . . . . . . . . . . 15.37kg . . . . . . . . . 26.77kg
PBJ20
© Jack Sealey Limited
PREMIER BOTTLE JACK
20TONNE, 30TONNE & 50TONNE
MODEL NO:
Beware crushing
Jack Saddle
hands
axis in line
(no offset load)
PBJ30
Original Language Version
PBJ20, PBJ30 & PBJ50
Use wheel
Use axle stands
chocks
PBJ20, PBJ30, PBJ50 | Issue 3 (H,F) 17/01/19
*
Note: no leadscrew on Model PBJ50
PBJ50
Advertisement
Related Manuals for Sealey PBJ20
Summary of Contents for Sealey PBJ20
- Page 1 PBJ20, PBJ30 & PBJ50 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Visually check the jack before each use for mechanical integrity, cracked welds, worn parts etc... If any damage is found, remove the jack from service. 5.7. Keep the piston rod clean and free of corrosion, clean exposed rod with a clean oiled cloth. Original Language Version PBJ20, PBJ30, PBJ50 | Issue 3 (H,F) 17/01/19 © Jack Sealey Limited...
- Page 3 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...