hit counter script
Download
Share
Print this page
Cisco Nexus 7000 Installing Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Switch
  5. Nexus 7000 Series
  6. Installing manual

Cisco Nexus 7000 Installing Manual

Switch chassis
Hide thumbs Also See for Nexus 7000:

Advertisement

Quick Links

Download this manual
Installing the Switch Chassis
This chapter includes the following topics:
•
•
•
•
•
•
•

Installing a Rack or Cabinet

Before you install the switch, you must install a standard four-post, 19-inch EIA data center rack (or a cabinet
that contains such a rack)
Bolt the rack to the concrete subfloor before moving the chassis onto it.
Note
Stability hazard. The rack stabilizing mechanism must be in place, or the rack must be bolted to the floor before
you slide the unit out for servicing. Failure to stabilize the rack can cause the rack to tip over.

Step 2

If the rack has bonded construction, connect it to the earth ground. This action enables you to easily ground the switch
and its components and to ground your electrostatic discharge (ESD) wrist strap to prevent damaging discharges when
you handle ungrounded components before installing them.
Step 3
If you need access to the source power at the rack, include either AC power receptacles or a DC power interface unit
(PIU) with the amperage required by the switch that you are installing. .
If you are using DC power, be sure that the DC power supply is grounded and that there is direct access to the facility
DC power or indirect access though a power interface unit (PIU). You must connect the DC power supply to the earth
ground before you connect it to the facility DC power.
Note
Take care when connecting units to the supply circuit so that wiring is not overloaded.
Cabinet and Rack
Requirements.
Installing the Switch Chassis
1

Advertisement

loading

Related Manuals for Cisco Nexus 7000

Summary of Contents for Cisco Nexus 7000

  • Page 1: Table Of Contents

    Installing the Switch Chassis This chapter includes the following topics: • Installing a Rack or Cabinet, on page 1 • Unpacking and Inspecting a New Switch, on page 2 • Installing the Chassis in a Two-Post Rack, on page 3 •...

  • Page 2: Unpacking And Inspecting A New Switch

    Installing the Switch Chassis Unpacking and Inspecting a New Switch If you are using the combined power mode or power-supply redundancy, you need only one power source. If Note you are using input-source redundancy or full redundancy, you need two power sources. Unpacking and Inspecting a New Switch Before you install a new chassis, you need to unpack and inspect it to be sure that you have all the items that you ordered and verify that the switch was not damaged during shipment.

  • Page 3: Installing The Chassis In A Two-Post Rack

    Installing the Switch Chassis Installing the Chassis in a Two-Post Rack • Air filter kit — Optional • Air filter (1) for the front door • Cable-management frame brush filters (2) • M3 x 12 mm flat-head Phillips screws (4) •...
  • Page 4 Installing the Switch Chassis Installing the Chassis in a Two-Post Rack Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: •...
  • Page 5 Installing the Switch Chassis Installing the Chassis in a Two-Post Rack Figure 1: Moving a Chassis onto a Rack or Cabinet Total of four M3 screws (for brackets on both sides). Total of eight M4 screws (for brackets on both sides). Step 4 Push the chassis all the way onto the rack so that the vertical mounting brackets on the chassis come in contact with the vertical mounting rails on the rack.
  • Page 6 Installing the Switch Chassis Installing the Chassis in a Two-Post Rack Figure 2: Attaching the Chassis to the Rack Vertical mounting rails on the rack Install a total of eight screws (user preference from the accessory kit) at the front to secure the chassis. Step 6 If you removed the fan tray before moving the chassis, reinstall each one in the chassis as follows: a) Holding each of the two handles on the fan tray with your two hands, align the fan tray to an open fan tray slot.

  • Page 7: Installing The Chassis On A Four-Post Rack Or Cabinet

    Installing the Switch Chassis Installing the Chassis on a Four-Post Rack or Cabinet The alignment bracket on top of the power supply should align to a track at the top of the slot and a bar at Note the bottom of the power supply should be guided by a track at the bottom of the slot. d) Slide the power supply all the way into the slot until its release handle clicks and the module stops.
  • Page 8 Installing the Switch Chassis Installing the Chassis on a Four-Post Rack or Cabinet • To remove a power supply, follow these steps: 1. Slide the handle in the middle of the ejector lever towards the end of the lever and rotate the lever away from the power supply.
  • Page 9 Installing the Switch Chassis Installing the Chassis on a Four-Post Rack or Cabinet Step 5 Use six screws (user preference from the accessory kit) at the front and four M3 screws at the back of the slide to secure the system chassis to the four-post rack Figure 4: Attaching the Chassis to the Rack Install six screws (user preference from the accessory Install 2 sliders to the C-shape bracket on each side...

  • Page 10: Grounding A Switch Chassis

    Installing the Switch Chassis Grounding a Switch Chassis d) Slide the power supply all the way into the slot until it stops. e) Slide the handle in the middle of the ejector lever toward the end of the lever and rotate the lever to the front of the power supply.

  • Page 11: Installing Cable Management Frames Onto The Chassis

    Installing the Switch Chassis Installing Cable Management Frames onto the Chassis • Crimping tool to crimp the grounding wire to the grounding lug. • Wire-stripping tool to remove the insulation from the grounding wire. Step 1 Use a wire-stripping tool to remove approximately 0.75 inch (19 mm) of the covering from the end of the grounding wire.
  • Page 12 Installing the Switch Chassis Installing Cable Management Frames onto the Chassis Step 1 Attach the two cable management frames to the chassis as follows: a) Position one of the cable management side frame assemblies on the vertical mounting bracket attached to one side of the front of the chassis.

  • Page 13: Attaching The Front Door To The Chassis

    Installing the Switch Chassis Attaching the Front Door to the Chassis Figure 7: Attaching the Top Hood to the Chassis and Cable Management Assemblies Side filter assembly Four M3 screws to secure the side filter to the cable management assembly. b) Attach the side filter assembly to the cable management assembly.
  • Page 14 Installing the Switch Chassis Attaching the Front Door to the Chassis • Number 1 manual Phillips torque screwdriver Step 1 Install the air filter to the front door as follows: a) Attach the air filter to the front door by aligning the plastic guides on the air filter with the slot holes on the front door.
  • Page 15 Installing the Switch Chassis Attaching the Front Door to the Chassis We recommend that you change the air filter every 3 months. However, examine the air filter once a month Note (or more often in dusty environments) and replace it if it appears to be excessively dirty or damaged. To comply with Telecordia GR-63-Core standard air filter requirements for NEBS deployments, the air filter must be replaced, not cleaned.
  • Page 16 Installing the Switch Chassis Attaching the Front Door to the Chassis Installing the Switch Chassis...

This manual is also suitable for:

Nexus 7702