Advertisement
Quick Links
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear protective
instruction
gloves
manual
1. safety
Familiarise yourself with the applications, limitations and hazards of the press.
9
maintain the press in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Keep the press clean for best and safest performance.
9
locate the press in an adequate working area for its function, keep area clean and tidy and free from unrelated materials and ensure
9
there is adequate lighting.
ensure the workpiece is correctly secured before operating the press.
9
ensure that all fittings are tight before each use.
9
WarninG! Always wear approved eye or face protection when operating the press. A full range of personal safety equipment is available
‰
from your Sealey stockist.
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain long hair.
9
Keep hands and body clear of the table when operating the press.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
9
do not operate the press if any parts are missing as this may cause failure and/or possible personal injury.
8
do not use the press for a task it is not designed to perform.
8
do not make any modifications to the press.
8
do not exceed the rated capacity of the press.
8
do not apply off-centre loads.
8
do not allow the workpiece or the arbor plates to fall from the table.
8
do not get the press wet or use in damp or wet locations or areas where there is condensation.
8
do not operate the press when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
do not climb upon the press.
8
do not use the press to compress a spring or any other item that could disengage and cause a potential hazard including personal
8
injury.
do not stand directly in front of a loaded press and never leave a loaded press unattended.
8
do not allow untrained persons to operate the press.
8
WarninG: do not top up hydraulic unit with brake fluid, or any other fluid other than a good quality hydraulic oil (sealey part
‰
number: hJo500mls/hJo5ls) as this may cause serious damage to the hydraulic unit and will invalidate the warranty.
When not in use, release pressure from the hydraulic unit and clean the press. Stand or store the arbor plates in a safe location.
9
2.
introduction
i
economy model is suitable for the serious enthusiast or occasional professional use. made from a high quality steel with a
powder coated finish to help corrosion resistance.
▲
danGer! This model is purpose designed to withstand greater loads than the hydraulic units can develop. For safety reasons, always
ensure the workpiece and press tools are secured on the table and will not flex or suddenly "give way" causing danger to operator or the
component.
3.
specification
i
Capacity .......................................................................10tonne
Ram stroke ....................................................................138mm
max height - ram to table ...............................................435mm
min height - ram to table ..................................................70mm
Table aperture .................................................................82mm
Table depth ....................................................................165mm
Table width ....................................................................418mm
overall height ..............................................................1305mm
Weight ...............................................................................42kg
© Jack Sealey limited
hydraulic press 10 tonne economy
floor type
model no:
Wear eye
Wear protective
protection
clothing
Original Language Version
yK10ecf
Wear safety
Warning:
footwear
Crushing of
hands
YK10eCF
Issue 2 02/08/18
Advertisement
Related Manuals for Sealey YK10ECF
Summary of Contents for Sealey YK10ECF
- Page 1 WarninG: do not top up hydraulic unit with brake fluid, or any other fluid other than a good quality hydraulic oil (sealey part ‰...
-
Page 2: Operating Instructions
6. maintenance note: maintenance and repair must only be carried out by qualified person. Contact your Sealey stockist for details. 6.1. When the press is not in use, the hydraulic unit ram must be fully retracted to minimise corrosion. Remove the handle to inactivate the press. - Page 3 Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. sealey Group, Kempson Way, suffolk business park, bury st edmunds, suffolk. ip32 7ar 01284 757500 01284 703534 sales@sealey.co.uk...