Advertisement
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
This product is NOT suitable for primary heating purposes.
1. SAFETY
1.1
ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
1.1.1.
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with
all electrical products. You may obtain an RCD by contacting your local Sealey stockist.
1.1.2.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.3.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.4.
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
DO NOT pull the plug from the socket by the cable.
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any
faulty item is repaired or is replaced immediately by a qualified electrician.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch off the electricity supply and remove
from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt
contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance
plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable.
1.2.
GENERAL SAFETY
DANGER! Risk of carbon monoxide poisoning. Failure to provide proper ventilation could result in serious illness or death.
Check that the heater is in sound condition and good working order. Take immediate action to repair or replace damaged parts.
Use recommended parts only. Unapproved parts may be dangerous and will invalidate the warranty.
Only use clean paraffin, kerosene or diesel (NOT BIO-DIESEL) to fuel your heater, in accordance with instructions contained in
this manual.
WARNING! Only use heater outdoors or in well ventilated areas. Ensure continuous ventilation from outside of the building is
provided to the heater operating area. Allow at least 3ft² opening/100000Btu/hr output.
Keep the front of the heater a minimum of 2.4 metres from any combustible materials (i.e. wooden items, cloth, plastics, paper,
etc).
Only operate on a level and stable surface.
WARNING! DO NOT use the heater near flammable material, liquids, solids, gases or compressed gas cylinders.
DO NOT use the heater in closed rooms, living areas, basements or below ground level.
DO NOT allow untrained persons to operate the heater.
DO NOT operate the heater without the cover.
DO NOT move or handle the heater when hot.
DO NOT leave the heater unattended when in use. Switch the heater off and unplug from the mains before leaving work area.
DO NOT fill the fuel tank whilst the heater is running or still hot.
DO NOT overfill the fuel container. Wipe up any spilt fuel immediately.
DO NOT obstruct the air inlet (rear) and air outlet (front) of the heater.
© Jack Sealey Limited
INSTRUCTIONS FOR:
SPACE WARMER PARAFFIN / KEROSENE /
DIESEL HEATER WITH WHEELS
mODEL NO:
Warning:
Warning:
Hot surface
Automatic
start up
Original Language Version
AB2158.V3
RECOMMENDED
FUSE RATING: 5AMP
AB2158.V3 Issue:3 (1,4,5,6) - 13/07/18
Advertisement
Table of Contents
Related Manuals for Sealey AB2158.V3
Summary of Contents for Sealey AB2158.V3
- Page 1 AB2158.V3 mODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 WARNING! This heater is not suitable for use with Bio-Diesel; use of Bio-Diesel will damage the filter and seals. Damage caused by use of Bio-Diesel will not be covered by warranty. Model AB2158.V3 215000 (63) Shell joining flanges, Rating BTU/hr (kW) both sides, bolted together Paraffin/...
-
Page 3: Operation
5.4. VENTILATION. Minimum recommended opening for fresh air intake, AB2158.V3 = 0.37m². WARNING! Only use the heater in well ventilated areas. Careful consideration must be given to the placing of the heater to provide ... -
Page 4: Maintenance
6.4.1 Remove the fan guard and filter end cover. 6.4.2 Take out the intake filter, wash it using a light detergent and dry thoroughly. 6.4.3 The Output and Lint filters should be replaced every 500 hours or less if the operating conditions demand. fig.8 fig.9 6.5. Fuel filter. The fuel filter (fig.10) should be cleaned twice per season, unless contamination occurs where it will require cleaning immediately. To clean the filter, remove and wash in paraffin. 6.6. Nozzle. The nozzle should be cleaned or replaced at least once per heating season. 6.6.1 To clean dirt from nozzle, Unscrew the four retaining screws and hinge open the top cover of the heater. 6.6.2 Remove the burner head and remove the nozzle (fig.11). 6.6.3 Blow compressed air through the front of the nozzle. For stubborn dirt it is advisable to soak the nozzle in clean paraffin to help loosen any particulate. 6.6.4 Refit nozzle and burner head in reverse order to above. 6.7. Flame-out device. The AB heaters are fitted with a flame-out device (a photocell, see fig.12), which cuts the fuel supply should the flame be inadvertently extinguished, or if the unit overheats. If this happens, switch off the heater and unplug from the mains supply. Check the heater to determine the fault. In particular check that the air intake is not obstructed and that the internal fan is rotating freely. Wait a few minutes and restart the unit. If the problem persists contact your local Sealey Service Agent. 6.8. Fan. Fan blades (fig.13) should be cleaned at least once per heating season, depending on environment. Remove the outer case top shell (fig.3) and clean the fan blades with a damp cloth. Dry fan thoroughly using compressed air. Original Language Version AB2158.V3 Issue:3 (1,4,5,6) - 13/07/18 © Jack Sealey Limited... - Page 5 7.1.2 Disconnect switch wires from the power switch. 7.1.3 Remove fuse from holder as shown. 7.1.4 Replace fuse with one of the same specification. WARNING! DO NOT substitute the fuse with one of a higher or lower current rating as this may result in a fire hazard. 7.1.5 Reconnect switch wires to the power switch. 7.1.6 Replace the side panel. fig.14 Original Language Version AB2158.V3 Issue:3 (1,4,5,6) - 13/07/18 © Jack Sealey Limited...
-
Page 6: Troubleshooting
Contact your local solid waste authority for recycling information. NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Sole UK Distributor, Sealey Group, www.sealey.co.uk 01284 757500 Kempson Way, Suffolk Business Park, W e b Bury St. Edmunds, Suffolk,...