Advertisement
Quick Links
Download this manual
See also:
Manual
LOGO!
Installation, Connection, Technical specifications
CSM 230
Order number: 6GK7177-1FA10-0AA0
A5E03733191-04
1
1
1
2
L1 N
X10
DC 115...210V
0.02...0.01A
AC 100...240V
~
0.02...0.01A
s
1
3
X1:P4
AC/DC
P1
P2 P3 P4
230V
LOGO! CSM230
6GK7177-1FA10-0AA0
X1:P1 TO X1:P4 FOR LAN ONLY
P2
P1
P3
X1:P1
X1:P2
X1:P3
1
52,4
71,5
Status of LEDs
RJ-45 jacks for connections via Ethernet (10/100 Mbps)
1
LED
Status
Meaning
Three screw terminals:
2
AC/DC
Off
Power is not connected or the connected
L1
Conductor
230V
power is too low.
N
Neutral Conductor
AC/DC
On
Power is connected.
Functional grounding
230V
P1 - P4
Off
No connection via Ethernet (link down).
LED for the power supply (AC/DC 230V) and
LEDs for the Ethernet communication status (P1 - P4)
P1 - P4
On
The connection via Ethernet is established (link up).
P1 - P4
Flashing
LOGO! receives / sends data via Ethernet.
© Siemens AG 2012
Wall mounting
Mounting slides
Hole pattern for wall mounting
Release 06/2012
Product information
All dimensions in mm
Hole for screw Ø 4 mm
Prior to wall-mounting, the mounting slides on the back
Tightening torque 0.8 ... 1.2 Nm
of the device are pushed open.
DIN rail mount
RJ-45 jacks with MDI-X assignment
1
L- N
X1:P4
AC/DC
P1
P2 P3 P4
230V
Pin 8 - n. c.
X1:P1
X1:P2
X1:P3
Pin 7 - n. c.
Pin 6 - TD -
Pin 5 - n. c.
Pin 4 - n. c.
Pin 3 - TD +
2
Pin 2 - RD -
Pin 1 - RD +
1. Fit the LOGO! onto the DIN rail.
2. Press down the lower part until the device locks in place.
The mounting slide on the back must snap into place.
Technical specifications
Ethernet interface
Communications connector
4 x RJ‑45 jacks with MDI‑X assignment 10/100 Mbps
36.0
(half / full duplex), autopolarity, autonegotiation
Network cable
A standard Ethernet cable can be connected to the Ethernet interface.
However, to minimize electromagnetic interference, Siemens
recommends a shielded Ethernet cable with a twisted pair
(category 5) with a shielded RJ-45 connector at both ends.
Largest data packet
1518 byte
Smallest data packet
64 byte
Delay resulting from latency
When a frame passes through the CSM 230, it is delayed
by the store and forward function of the switch:
- with a 64 byte frame length by approx. 8 μs (at 100 Mbps).
- with a 1518 byte frame length by approx. 125 μs (at 100 Mbps).
Topology
Star and bus topology
Note that the direct connection of two ports on the switch or
accidental connection over several switches causes an illegal loop.
Such a loop can lead to network overload and network failures.
Insulation of the ports
All ports adhere to 1.5 kV insulation voltage:
- to shield
- between the ports.
Learnable MAC addresses
1024
Aging Time
300 seconds
Electrical specification
Input voltage
AC 100 ... 240 V
DC 115 ... 210 V
Permitted line power frequency
AC 47... 63 Hz
Current consumption (I)
- AC 100 ... 240 V: 0.05 ... 0.03 A
- DC 115 ... 210 V: 0.02 ... 0.012 A
Effective power loss
1.8 W
Connection
Per terminal for L1 and N
Cable cross section: 1 x 2.5 mm
2
or 2 x 1.5 mm
2
Functional grounding
Functional grounding can be established by connecting a cable
from terminal 3, for example to the DIN rail. Such a cable should be
kept as short as possible. Grounding is, however, not necessary for
interference-free operation.
Technical specifications
The product meets the requirements and aims of the following EC directives:
Further technical specifications
EU Directive 2004/108/EC "Electromagnetic Compatibility" (EMC Directive)
Operating temperature
- Emission: EN 55022 Class B: 2010
0 ... 55°C
- Immunity: EN 61000-6-2: 2005
Transport/storage temperature
- 40°C ... +70°C
EU Directive 2006/95/EC "Low Voltage Directive" (LVD)
- Safety: EN 61131-2: 2008
Relative humidity during operation
< 90% (no condensation)
The EC Declaration of Conformity is available for all responsible authorities at:
Dimensions (W x H x D) in mm
72 (4 TE) x 90 x 55 mm
Siemens Aktiengesellschaft
Net weight
155 g
Industry Automation, I IA SC CI
Postfach 4848
Installation
35 mm DIN rail (DIN EN 60715 TH35) or wall mounting
D-90026 Nuernberg
Germany
Degree of protection
IP 20
You will find the EC Declaration of Conformity for this product on the Internet
at the following address:
Approvals
You will find the currently valid approvals on the type plate.
http://support.automation.siemens.com/WW/view/en/10805878
→ Tab "Entry List"
cULus
- UL 508 Listed
Filter settings: Entry type: "Certificates"
- CSA C22.2 Number 142
Certificate Type: "Declaration of Conformity"
C-Tick
AS/NZS 2064 Class A
Search items(s): <name of the module>
You can use the device in the following hazardous locations:
cULus Haz.Loc.
IND. CONT. EQ., E223122, UL 1604, UL 2279-15
Sources of information and other documentation
FM
FM3600 and 3611:
CL. I, Div. 2, Group A, B, C, D, T4
The "SIMATIC NET Industrial Ethernet Network Manual" contains
CL. I, Zone 2, Group IIC, T4, Ta = 55°C
detailed information on the network structure, maximum cable lengths,
cabling technology etc.
Installation
Prior to installation, connecting up and commissioning, read the relevant sections
http://support.automation.siemens.com/WW/view/en/27069465
in the LOGO! manual:
Entry ID: 27069465
http://support.automation.siemens.com/WW/view/en/50074616
You will find additional information on the Siemens LOGO! Web page:
Entry ID: 50074616
When installing and connecting up, keep to the procedures described in the LOGO! manual.
http://www.siemens.com/logo
To fulfill the requirements according radiated emission EN 55022 Class B, the shield of all
connected LAN cables must be grounded.
Sources of information and other documentation
The "SIMATIC NET Industrial Ethernet Networking Manual" contains detailed information
on the network structure, maximum cable lengths, cabling technology etc.
http://support.automation.siemens.com/WW/view/en/27069465
Entry ID: 27069465
You will find additional information on the Siemens LOGO! web page:
http://www.siemens.com/logo
Advertisement
Related Manuals for Siemens LOGO!
Summary of Contents for Siemens LOGO!
- Page 1 X1:P2 X1:P3 Permitted line power frequency AC 47... 63 Hz http://support.automation.siemens.com/WW/view/en/50074616 You will find additional information on the Siemens LOGO! Web page: Entry ID: 50074616 Current consumption (I) - AC 100 ... 240 V: 0.05 ... 0.03 A 52,4 When installing and connecting up, keep to the procedures described in the LOGO! manual.
- Page 2 Important notes Wichtige Hinweise Avvertenze importanti Indicaciones importantes Remarques importantes 重要事项 Hinweis Remarque Nota Nota Notice Stellen Sie sicher, dass Sie bei der Verdrahtung Ihrer LOGO! alle geltenden und Accertarsi sempre che il cablaggio di LOGO! sia conforme alle regole e alle norme Vigile siempre que el cableado del LOGO! cumpla todas las reglas y normas vigentes.