Advertisement
Quick Links
HONEYWELL EXCEL 5000 OPEN SYSTEM
GENERAL
The T7560A,B Digital Wall Modules (DWM) display and
provide space temperature, setpoint, Occupied/Unoccupied
override, and fan mode/speed selection for the Honeywell
Excel 10 W7750, W7751H (see also Table 5,) W7752,
W7753, W7754, W7761, W7762, W7763, and Excel 800,
600, 500, 100, 50, 20 Controllers, as applicable. A software
module ModAL is available to adapt the wall module to the
respective Excel 20, 50, 100, 500, 600, 800 controller. See
T7560A,B,C Installation Instructions (product literature no.:
EN1B-0146GE51) for details.
Using the three buttons, the user can change room
temperature setpoint, fan mode/speed, initiate/cancel bypass,
and change configuration information such as the DWM's
engineering units.
The T7560C Digital Wall Module (see inset above) has no
user interface (e.g. LCD, buttons, or setpoint dial) and issues
only temperature and humidity values.
These wall modules are not compatible with Honeywell
W7751A,C,E,G (VAV1) and W7752D1 (FCU1) Controllers.
® U.S. Registered Trademark
Copyright © 2009 Honeywell Inc. • All Rights Reserved
For latest prices and delivery to your door visit MyTub Ltd - 0845 303 8383 - www.mytub.co.uk - info@mytub.co.uk
T7560A,B,C Digital Wall Module
FEATURES
•
Fully compatible with all current Excel 10 and Excel
20 to 800 controllers.
•
Low power consumption.
•
Integral 20kΩ NTC sensor.
•
Separate mounting base for easy installation.
•
Tamper-resistant locking cover.
•
IP30 housing.
•
T7560A and B, only:
LCD display continuously shows current space
-
temperature, occupied/unoccupied/standby mode,
fan status/mode, humidity, as configured.
Push-button interface for full navigation and
-
change control of wall module functions.
Single-touch occupied/unoccupied override.
-
Setpoint dial for setpoint adjustment.
-
Fan Speed/Mode commandable from buttons.
-
Selectable °F/°C temperature display.
-
Selectable setpoint type, absolute or relative.
-
SPECIFICATION DATA
EN0B-0237GE51 R0509
Advertisement
Related Manuals for Honeywell T7560A
Summary of Contents for Honeywell T7560A
- Page 1 GENERAL Selectable °F/°C temperature display. Selectable setpoint type, absolute or relative. The T7560A,B Digital Wall Modules (DWM) display and provide space temperature, setpoint, Occupied/Unoccupied override, and fan mode/speed selection for the Honeywell Excel 10 W7750, W7751H (see also Table 5,) W7752, W7753, W7754, W7761, W7762, W7763, and Excel 800, 600, 500, 100, 50, 20 Controllers, as applicable.
-
Page 2: Specifications
The DWM is furnished with a 20kΩ NTC temperature sensor that follows a specific temperature-resistance curve. See Fig. runs at speed 1 1. Honeywell controllers used with the DWM employ an runs at speed 2 algorithm providing readings close to the actual temperature. - Page 3 T7560A,B,C DIGITAL WALL MODULES Field Wiring • 16 to 22 AWG (1.5 to 0.34 mm ) depending on application. • 18 AWG (1.0 mm ) min. for 24 Vac power wiring. • Max. length of wire from a device to a wall module is 164 ft (50 m).
- Page 4 After the new setpoint has been set, the display returns to normal AUTO The T7560A and T7560B feature three buttons, a setpoint mode after approx. 5 sec. dial, and the LCD display (see Fig. 2). This section describes the functions of these elements. Table 5 shows the functions Set Fan Speed available with the different Excel 10 Controllers.
-
Page 5: Humidity Display
Override mode display for Excel 10 LED signaling (Excel moon, and snowflake symbols. The following LCD behaviors 10 set to LED_OVERRIDE) are possible, depending on configuration. See T7560A,B,C Installation Instructions (product literature no.: EN1B- Off Conditions, No Override, Overr. 0146GE51) for configuration options: Occupancy, Overr. - Page 6 Order quantity: set of 5 pieces Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Rolle, Z.A. La Pièce 16, Switzerland by its Authorized Representative: Automation and Control Solutions Honeywell GmbH Böblinger Strasse 17...