Miele F 1801 SF Operating And Installation Instructions
Hide thumbs
Also See for F 1801 SF:
- Operating and installation instructions (72 pages) ,
- Operating and installation manual (72 pages) ,
- Installation instructions manual (24 pages)
Related Manuals for Miele F 1801 SF
Summary of Contents for Miele F 1801 SF
- Page 1 Operating and Installation Instructions Freezer F 1801 SF F 1811 SF F 1901 SF F 1911 SF en - US, CA To prevent accidents and machine damage read these instructions before installation or use. M.-Nr. 07 360 800...
-
Page 2: Installation Instructions
Installation instructions To prevent accidents and machine damage read these instructions before installation or use. -
Page 3: Caring For The Environment
Caring for the environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing Old appliances contain materials that materials are biodegradable and can be recycled. Please contact your recyclable. Please recycle. local recycling center about the possibility of recycling these materials. -
Page 4: Installation Site
Installation Installation site Have the appliance installed by a The appliance should be installed in a qualified technician, according to dry, well-ventilated room. the enclosed installation instructions. Do not install the appliance: The manufacturer is not liable for - outdoors damage to property due to an - in an environment with dripping incorrect installation or water... - Page 5 See "Niche dimensions". If in doubt, contact Miele. The side walls of the installation cavity Furniture/fixtures must be plumb. The new appliance will be mounted...
-
Page 6: Installation Options
"Merging Kit". The "Merging Kit" can be obtained from The door hinge cannot be Miele. exchanged. Contact Miele or your dealer for Single column specific information about which The appliance can be installed at any combinations will work with your preferred location in the kitchen. -
Page 7: Side Panels
Installation . . . with partition The "Merging Kit" can be obtained The minimum thickness of the partition from Miele. " (16 mm). If there is a partition between the Side panels adjacent appliances, then each If one side of the appliance is visible, a appliance is to be individually installed side panel must be used. - Page 8 Dimensions Niche dimensions F 18X1 SF 30 1/2" (774.6 mm) 30" (762 mm) F 19X1 SF 36 1/2" (927 mm) 36" (915 mm)
-
Page 9: Door Dimensions (Open 115°)
Dimensions 1. Power supply 2. Water connection F 18X1 SF 15" (381 mm) F 19X1 SF 18" (458 mm) Door dimensions (open 115°) F 18X1 SF " (829 mm) " (363 mm) F 19X1 SF " (982 mm) " (428 mm) -
Page 10: Installing The Appliance
Installing the appliance Before you begin Tools needed for installation – Cutter with adjustable blade Read these instructions completely and carefully. – Cordless screwdriver T 20 Have the appliance installed by a – Torx screwdriver T 20 qualified technician, according to the enclosed installation instructions. -
Page 11: Check The Installation Niche
Installing the appliance Check the installation niche Before installation To ensure a safe, trouble-free Caution - the appliance is very installation and the best possible heavy. Use caution when unpacking cosmetic result, check to be sure and opening the door, danger of that the installation space complies tipping. -
Page 12: Remotevision Module Installation
Installing the appliance ^ Loosen the bracket that holds the appliance to the pallet. ^ Unscrew the screws a on the cover b and pull off the sticker c. Caution! The appliance is no ^ Remove the cover b. longer secured and may be unstable. -
Page 13: Preparing The Installation Niche
In that case, repeat the process. If that does not correct the Keep the appliance door closed problem, contact Miele. until it is securely fastened in the niche. Tipping hazard. If the installation niche is deeper than the appliance, a solid wooden beam a ^ Pull the antenna d straight out. - Page 14 Installing the appliance Anti-tip brackets The anti-tip brackets help keep the appliance safely secured to the installation niche to prevent tipping. Two anti-tip brackets are recommended for each appliance or appliance combination (side-by-side). ^ Drill pilot holes: – " (3 mm) for 5 x 60 mm wood screws –...
- Page 15 Installing the appliance Securing an alternative anti-tip – The beam must cover the appliance by at least 2" (50.8 mm). device ^ Mark the installation height (lower If the anti-tip brackets cannot be attached securely, an alternative edge of the beam) on the rear wall of anti-tip device can be used.
-
Page 16: Sliding The Appliance Into The Installation Niche
Installing the appliance Sliding the appliance into the In the case of side-by-side installation niche installations, a separate outlet must be used for each appliance. ^ To prevent the power cord from becoming caught: Tie a piece of string to the middle of the power cord and feed it forward under the appliance. -
Page 17: Aligning The Appliance
Installing the appliance Aligning the appliance A mark is located on the appliance base and is used as a standard gauge ^ Align the appliance with the for height adjustment. When adjusting surrounding cabinets. the height, align this mark at 1 "... -
Page 18: Attaching The Appliance To The Installation Niche
Installing the appliance Attaching the appliance to the Note: installation niche – Do not twist or jam the appliance inside the niche. When unscrewing the height-adjustable feet, proceed gradually, alternating between left and right. – The adjustment of the rear feet is aided if the appliance is lifted at the rear (tipped forward slightly). -
Page 19: Attaching The Toe-Kick Panel
Installing the appliance Attaching the toe-kick panel The maximum height of the toe-kick panel is 4" from the top of the floor. Do not cover the ventilation slits in the base panel. Risk of damage to the appliance. ^ If required, cut the toe-kick panel to the required length and height. - Page 20 Installing the appliance Mounting the air separator The air separator keeps the supply and exhaust air separate. This prevents warm exhaust air from flowing into the machine, optimizing the energy performance of the unit. ^ Position the air separator in the center of the appliance door.
- Page 21 Plumbing All plumbing work should be carried out by a suitably qualified and competent person, in accordance with all applicable local and national regulations. The manufacturer is not liable for damage to property due to an incorrect installation or water connection.
- Page 22 Plumbing Preparing the water connection The connection to the household water supply must be installed before the appliance is installed. ^ Turn off the main water valve to prevent damage caused by leaking water. ^ Attach the connecting pipe to the shut-off valve, according to the instructions supplied by the manufacturer of the ice cube maker...
-
Page 23: Connecting The Water Supply
Plumbing ^ Push the union nut and seal onto the Connecting the water supply water pipe. When connecting the water pipe to ^ Push the end of the water pipe into the solenoid valve of the appliance, the appliance connection and screw follow the instructions supplied by on the union nut, 3. -
Page 24: Electrical Connection
If there are any questions regarding the electrical connection of this appliance to the power supply, please consult a licensed electrician or call the Miele Technical Service. U1-800-999-1360 V1-800-565-6435... - Page 25 Alteration rights reserved / 3408 M.-Nr. 07 360 800 / 01 For the most updated manual see the Miele web site.