Table of Contents
Advertisement
Quick Links
Introduction to the NEC MultiSync LCD
E - 1
2110
Introduction to the NEC MultiSync LCD
2110
Congratulations on your purchase of the NEC MultiSync LCD
true
2110
colour monitor!
NuCycle Plastic
A special silicone compound for PC resin, being extremely flame-
retardant, safe and environmentally friendly.
Wide Viewing Angle Technology
Allows the user to be able to see the monitor from any angle(170 degrees)
from any orientation – Portrait or Landscape. Provides full 170˚ viewing
angles either up, down, left or right.
Analog Advantage
Capable of displaying unlimited colours in a continuous spectrum,
providing a truer representation of colour. The monitor's high contrast
LCD enhances colour vibrancy and improves focus with no geometric
distortion.
Wider Compatibility
Because the MultiSync LCD monitor is analog through and through, it
does not require special analog to digital display or interface cards but
can accept RGB input directly.
Reduced Footprint
Provides the ideal solution for environments requiring superior image
quality but with size and weight limitations. The monitor's small footprint
and low weight allow it to be moved or transported easily from one
location to another.
Colour Control system
Allows you to adjust the colours on your screen and customize the colour
accuracy of your monitor to a variety of standards.
78134811.PM5
11
99.12.24, 2:19 PM
Advertisement
Table of Contents
Related Manuals for NEC colour monitor
Summary of Contents for NEC colour monitor
- Page 1 Introduction to the NEC MultiSync LCD E - 1 2110 Introduction to the NEC MultiSync LCD 2110 Congratulations on your purchase of the NEC MultiSync LCD true 2110 colour monitor! NuCycle Plastic A special silicone compound for PC resin, being extremely flame- retardant, safe and environmentally friendly.
- Page 2 E - 2 Introduction to the NEC MultiSync LCD 2110 OSM (On-Screen Manager) Controls Allow you to quickly and easily adjust all elements of your screen image via simple to use on-sreen menus. ErgoDesign Features Enhance human ergonomics to improve the working environment, protect the health of the user and save money.
- Page 3 Introduction to the NEC MultiSync LCD E - 3 2110 FullScan Capability Allows you to use the entire screen area in most resolutions, significantly expanding image size. VESA Standard Mounting Interface Allows users to connect their MultiSync monitor to any VESA standard third party mounting arm or bracket.
-
Page 4: Contents Of Package
– AC Adapter. (Type A2440S01) – Video Signal Cable – 15 pin VGA to BNC. – User’s manual. – NEC LCD Setup Software, Pivot Software and other helpful files. Remember to save the original box and packing materials to transport or ship the monitor. -
Page 5: Recommended Use
• Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any cleaning solution, glass cleaner or tissue paper. 78134811.PM5 colour monitor: 2110 99.12.24, 2:19 PM E - 5... - Page 6 E - 6 • For optimum performance, allow 20 minutes for warm-up. • Avoid displaying fixed patterns on the monitor for long periods of the time to avoid image persistence (after-image effects.) • Avoid applying pressure to the LCD monitor surface. •...
- Page 7 Recommended Use • Handle with care when transporting. Save packaging for transporting. • This LCD monitor is designed for use with a flexible arm, therefore it is delivered without stand. Please use the attached screws (4pcs) when installing. To fulfil the safety requirements the monitor must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor.
- Page 8 E - 8 Installation Connection to your Personal Computer The MultiSync LCD true colour monitor complements PC compatible 2110 computers. Your system has one of two configurations: – the video controller is built into the computer. – the video controller is in the form of a display card (sometimes referred to as graphics card, video adapter or graphics board).
- Page 9 Installation (Figure C.1). Place the 15-pin VGA to BNC Cable under clip A (Figure D.1A). Then place the 15-pin VGA to BNC cable under Clip B (FigureD.1B). 5. Connect the D-SUB cable to D-SUB connector on the back of the monitor (Figure C.2). 6.
- Page 10 For a full description of these OSM controls, refer to the Controls section of this User’s Manual. 10. Refer to User’s Manual in the NEC LCD Setup Software CD case for installation and operation of this software. NOTE: If you have any problems, please refer to the Troubleshooting section of this User’s Manual.
-
Page 11: Raise And Lower Monitor Screen
Installation G(/SYNC) HS/CS Figure C.1 Power Button Figure F.1 Figure D.1A Figure L.1 Figure J.1A Raise and Lower Monitor Screen The monitor may be raised or lowered in either Portrait or Landscape mode. To raise or lower screen, place hands on each side of the monitor and lift or lower to the desired height (Figure RL.1). -
Page 12: Tilt And Swivel
E - 12 Installation Tilt and Swivel Grasp both sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1). Figure RL.1 Figure R.1 Figure TS.1 78134811.PM5 99.12.24, 2:19 PM... -
Page 13: Remove Monitor Stand For Mounting
Installation Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1. Disconnect all cables. 2. Place hands on each side of the monitor and lift up to the highest position (Figure RL.1). 3. Place monitor face down on a non-abrasive surface (Place the screen on a 55mm platform so that the stand is parallel with the surface.) (Figure S.1). -
Page 14: Osm Controls
E - 14 Controls BNC/D-SUB:Allows you to change between the BNC and D-SUB signal inputs. OSM Controls The OSM controls on the front of the monitor provide the following functions: To access OSM press any of the control buttons ( , , , ) or the PROCEED or EXIT button. - Page 15 Controls Brightness/Contrast Controls BRIGHTNESS Adjusts the overall image and background screen brightness. CONTRAST Adjusts the image brightness in relation to the background. AUTO ADJUST CONTRAST Adjusts the image displayed for non-standard video inputs. Auto Adjust Automatically adjusts the Image Position, H. Size and Fine settings.
- Page 16 E - 16 Image Adjust Controls H. SIZE Adjusts the horizontal size by increasing or decreasing this setting. FINE Improves focus, clarity and image stability by increasing or decreasing this setting. Automatically adjusts the H. Size and Fine settings. Colour Control System Five colour presets select the desired colour setting.
- Page 17 Controls Information Indicates the current display resolution, frequency setting and type of Sync signal of the monitor. NOTE: If the highlighted, then Sync Type is switched between Separate Sync and Sync On Green. OSM LOCK OUT The OSM LOCK OUT control completely locks out access to all OSM control functions.
-
Page 18: Multisync Lcd
E - 18 Multisync LCD 2110 Display 54.1 cm (21.3 inch) viewable image size; 1600 x 1200 native resolution (Pixel Count); active matrix; thin film transistor (TFT); liquid crystal display (LCD); 0.27 mm dot pitch; 180 cd/m 250:1 contrast ratio, typical Input Signal Video Sync... - Page 19 ** NEC cites recommended resolutions at 60 Hz for optimal display performance. *** Active display area is dependent upon the signal timing. Technical specifications are subject to change without notice.
-
Page 20: Troubleshooting/Support
”ghost” of that image remains, the monitor should be turned off for one hour to erase the image. NOTE: As with all personal display devices, NEC recommends using a screen saver at regular intervals whenever the screen is idle. - Page 21 Troubleshooting/Support Problem Image is unstable, unfocused or swimming is apparent LED on monitor is not lit (no green or amber colour can be - Make certain the computer is not in a power-saving seen) Display image has a Select “TYPE” in the OSM Information menu green cast to it Display image is not - Use the OSM Image Adjust controls to increase or sized properly...