Hitachi WF 14DSL Handling Instructions Manual
Hide thumbs
Also See for WF 14DSL:
- Handling instructions manual (85 pages) ,
- Handling instructions manual (52 pages)
Related Manuals for Hitachi WF 14DSL
Summary of Contents for Hitachi WF 14DSL
- Page 1 Cordless Automatic Screw Driver WF 14DSL • WF 18DSL WF14DSL Read through carefully and understand these instructions before use. Handling instructions...
- Page 2 〈UC18YFSL〉 〈UC18YSL3〉 &...
- Page 3 5 mm...
- Page 4 3 mm 11.5 mm...
- Page 5 Rechargeable battery Screw feed attachment Latch Driver bit No.2 (136L) Battery cover Socket hexagonal hole Terminal Guide sleeve Ventilator Wall Push Screw Pull out Guide to prevent damage to wall Handle 15 mm over Charger Sheet Charging time indicator lamp Protrusion Screw Rubber cover...
-
Page 6: General Power Tool Safety Warnings
c) Prevent unintentional starting. Ensure the GENERAL POWER TOOL SAFETY WARNINGS switch is in the off -position before connecting to power source and/or battery pack, picking WARNING up or carrying the tool. Read all safety warnings and all instructions. Carrying power tools with your fi nger on the switch Failure to follow the warnings and instructions may result in or energising power tools that have the switch on electric shock, fi... -
Page 7: Caution On Lithium-Ion Battery
5) Battery tool use and care 11. One-hand operation is extremely dangerous; hold the a) Recharge only with the charger specifi ed by unit fi rmly with both hands when operating. the manufacturer. 12. Use original bits specifi cally for the automatic A charger that is suitable for one type of battery screwdriver. -
Page 8: Usb Device Connection Precautions
○ Do not store an unused battery in a location exposed to ○ For transportation abroad, you must comply with swarf and dust. international law and the rules and regulations of the ○ Before storing a battery, remove any swarf and dust that destination country. -
Page 9: Specifications
SPECIFICATIONS POWER TOOL Model WF14DSL WF18DSL No-load speed 4200 /min Screw size 4 mm Capacity Screw length 25 – 41 mm Bit shank size 6.35 mm Hex. BSL1430: BSL1440: BSL1450: BSL1830: BSL1840: BSL1850: BSL1860: Rechargeable battery Li-ion 14.4 V Li-ion 14.4 V Li-ion 14.4 V Li-ion 18 V Li-ion 18 V... - Page 10 Table 1-a Indications of the pilot lamp Lights for 0.5 seconds. Does not light Before for 0.5 seconds. (off for 0.5 seconds) Blinks charging Lights continuously While Lights charging Lights for 0.5 seconds. Does not light Charging for 0.5 seconds. (off for 0.5 seconds) Pilot lamp Blinks complete...
-
Page 11: Prior To Operation
30 seconds or so. If this does not cause ○ When not operating the tool, always set the reversing the pilot lamp or charge indicator lamp to blink in red switch lever to the neutral position. (every second), please take the charger to the Hitachi Authorized Service Center. - Page 12 2. Attaching and removing the bit (Fig. 16) ADJUSTING THE SCREW LENGTH AND No bits other than plus driver (Phillips) bits (No. 2, 136 SCREW-IN DEPTH mm long) can be used for screw strip tightening jobs. Attach the bits securely using the following procedure. 1.
-
Page 13: Maintenance And Inspection
7. About Remaining Battery Indicator When replacing the carbon brush with a new one, be When pressing the remaining battery indicator switch, sure to use the Hitachi Carbon Brush Code No. 999054. the remaining battery indicator lamp lights and the 5. Replacing carbon brushes battery remaining power can be checked. - Page 14 8. Service parts list CAUTION Repair, modifi cation and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance.
- Page 16 Hitachi Koki Co., Ltd. Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. C99205911 G Printed in China...